CATTRON Theimeg AT & ATS 816 Series INSTALLATION, OPERATION & MAINTENANCE Manual – PDF DOWNLOAD
FILE DETAILS:
CATTRON Theimeg AT & ATS 816 Series INSTALLATION, OPERATION & MAINTENANCE Manual – PDF DOWNLOAD
Language : English
Pages : 108
Downloadable : Yes
File Type : PDF
IMAGES PREVIEW OF THE MANUAL:
TABLE OF CONTENTS:
CATTRON Theimeg AT & ATS 816 Series INSTALLATION, OPERATION & MAINTENANCE Manual – PDF DOWNLOAD
Front Matter
Important Notices i
List of Technical Abbreviations ii
Safety Summary iii
Warnings iii
Cautions vii
General viii
Section 1 – Functional Description
General 1-1
Operability 1-1
Advanced Control Functions 1-1
AT & ATS 816 Series Receiver/Decoders – Functional description 1-2
Specifications 1-3
System Features 1-4
Safety Considerations 1-5
Standard Safety & Security Features 1-5
Principle of Operation 1-6
Radio Remote Control 1-6
AT & ATS 816 Series PRC Systems – model summary chart 1-7
Section 2 – Installation
Pre-installation checks 2-1
Interface connections 2-1
Introduction 2-1
Safety Interface Unit (ATS 816 Series only) 2-2
The controlled machine 2-4
Control transformer 2-4
Disconnect and outlet 2-5
Page x ã04/2006, CATTRON-THEIMEG™
Section 2 – Installation, continued
Transfer switch 2-5
Relay outputs 2-6
R/C snubbing 2-6
Mainline circuit (operate and reset relays) 2-6
Attenuator 2-8
Installation 2-9
Getting started 2-9
Choosing a mounting location 2-9
Remote antenna location 2-10
Triple diversity antenna 2-11
Direct DC wiring option 2-12
Pre-set frequency selections (ATS 816 Series only) 2-13
Post installation checks 2-14
System status display and LED indicators 2-14
Check-out procedures 2-16
Power-up messages 2-16
Run-time Messages 2-17
ASO Hexadecimal Codes 2-19
Section 3 – Operating Instructions
General 3-1
Section 4 – Maintenance
General 4-1
Preventive maintenance 4-2
Typical additional checks 4-2
Primary power supply 4-2
Fuses 4-2
Fuse holders 4-3
Unit assemblies 4-3
Antenna system 4-3
ã04/2006, CATTRON-THEIMEG™ Page xi
Section 4 – Maintenance, continued
Netting 4-3
Adjustments 4-4
Troubleshooting 4-5
Automatic Safety Override (ASO) 4-9
ASO Circuit test procedure 4-9
Receiver/Decoder repair 4-11
Replacing the EMI/RFI shielded chassis (gold box) 4-11
Relay replacement 4-12
Receiver replacement 4-13
Decoder replacement 4-15
Code Plug replacement 4-17
EPROM replacement 4-20
Section 5 – Parts List and Accessories
Introduction 5-1
AT & ATS 816 Series Receiver/Decoder 5-2
EMI/RFI Shielded Chassis 5-4
Accessories 5-6
Two-step electro-hydraulic brake package 5-6
Transfer Switch 5-7
Appendix ‘A’ – R1014T2 Receiver
Introduction A-1
Additional Safety Feature A-2
Close Start Setup A-2
Range Limit Setup A-7
Range Extender Setup A-10
Scanner Setup A-12
Attenuator Setup A-13
Factory Set & Field Programmable Frequencies A-14
Page xii ã04/2006, CATTRON-THEIMEG™
Appendix ‘B – New R1HN and R2HN Receiver Boards
Frequency Programming Procedure B-1
Index
Addendum
RECOMMENDED SAFETY RULES FOR PORTABLE REMOTE CONTROLLED
(PRC) CRANES
DESCRIPTION:
CATTRON Theimeg AT & ATS 816 Series INSTALLATION, OPERATION & MAINTENANCE Manual – PDF DOWNLOAD
GENERAL:
- The following are general safety precautions that are not related to any specific procedure and
therefore do not appear elsewhere in this manual. These are general safety precautions and instructions
that people must understand and apply during many phases of operation and maintenanc e to ensure
personal safety and health and the protection of your company property.
KEEP AWAY FROM LIVE CIRCUITS. Maintenance personnel must observe all safety requirements
at all times. Do not replace components or make adjustments inside the equipment with the electrical
supply turned on. Under certain conditions, danger may exist even when the power control is in the off
position due to charges retained by capacitors. To avoid injuries, always remove power, discharge and
ground a circuit before touc hing it. Adhere to all lock out/tag out requirements.
DO NOT SERVICE OR ADJUST ALONE. Whenever possible, do not attempt internal service or
adjustment of equipment unless another person capable of rendering aid and resuscitation is present.
FINGER RINGS/JEWELRY. Finger rings have caused many serious injuries. Remove rings, watches
and other metallic objects which may cause shock or burn hazards.
SOLDERING/DE-SOLDERING. Avoid breathing fumes generated by soldering/de-soldering.
Perform all operations in a ventilated area. Eye protection is required.
CLEANING SOLVENTS. Some cleaners and solvents have adverse effects on skin, eyes, respiratory
tract and internal organs. These adverse effects range from discomfort to serious injury and death,
depending on the material and degree of exposure. Observe manufacturers’ warning labels and contact
your immediate supervisor if in any doubt.
S.V 29/03/2025
