CASE 1150B CRAWLER SERVICE REPAIR MANUAL (9-72547) CASE 1150B – PDF Download

Description

CASE 1150B CRAWLER SERVICE REPAIR MANUAL (9-72547) CASE 1150B

CASE 1150B CRAWLER SERVICE REPAIR MANUAL (9-72547) CASE 1150B – PDF DOWNLOAD:

Image Preview:

Description:

CASE 1150B CRAWLER SERVICE REPAIR MANUAL (9-72547) CASE 1150B

Engine Lubrication
When the engine rebuild is complete, fill the engine crankcase with Case HDM oil and install new engine oil filters. NOTE: If Case HDM oil is not used, use only a Series 3 DS or CD Service Classification oil that has the proper viscosity rating for prevailing air temperature. Refer to vehicle Operators Manual.
After the first 20 hours of operation, change the engine oil while the engine is hot and replace the the engine oil filterz’s. DO NOT DRAIN OIL UNTIL THE ENGINE HAS BEEN OPERATED 20 HOURS.
Change the engine oil and filter/s at the recommended intervals thereafter as outlined in the Operator’s Manual.
Run-in Procedure (Agricultural Tractors)
For the first 8 hours of field operation stay one gear lower than normal. For the next 12 hours DO NOT “lug” the engine. Prevent “lugging” by shifting to a lower gear. The engine must not be “lugged” below its Rated Engine RPM during the early hours of life.
Run-In Procedure (Construction Equipment)
For the first 8 hours, operate the engine at full throttle maintaining a normal load. DO NOT baby the engine. but avoid prolonged converter or hydraulic stall. Engine must not be “lugged” below its Rated Engine RPM (Do not exceed 10 seconds of stall).
Run-In Procedure (Power Units)
For the first 1/2 hour, operate engine at 2/3 rated RPM with a light load or no load. For the next (1) hour, run engine at 80 to 90% load at rated RPM (but not over 2000 RPM). Then full load and rated RPM as required in application.

Table of Contents:

CASE 1150B CRAWLER SERVICE REPAIR MANUAL (9-72547) CASE 1150B

10 SERIES-GENERAL
General EngineSpecifications
Detailed EngineSpecifications
Detailed FuelSpecifications
Maintenanceand Lubrication
TorqueChart
20 SERIES-ENGINE
EngineDlagnosis
EngineTune—Up
Cylinder Head Valve Train and Camshaft
Cylinder Block,SIeeves Pistons and Rods
Crankshaft Main Bearing, Flywheel and Oil Seal Replacemei
Lubrication Syslem
Stall Checks, Engine Rem0val and Installation
Air Cleaner
Ether Injector STarting Aid
Cooling System
30 SERIES—FUEL SYSTEM
Fuel System and Filter
Fuel injection Pumps
Fuel injectors
Fuel Tank Lines and Throttle Adjustment
40 SERIES-HYDRAULICS
Diagrams Troubleshooting Maintenance, Adjustments
FlowmeterTests
Exploded ViewsoiHydraulic System
DiversionValveR24819
EquipmentPumpR25852
EquipmentControlValves
Loader,Ripperand DozerCyIinders
50 SERIES – TRACK AND SUSPENSION
TrackSystem
Track System – Idlers (Without Lubricant Fill Plug in Hub)
Track System – Track Frame Removal and installation
SuspensionSystem
GuideLevers
lntertracRollers
60 SERIES-POWER TRAIN
Transmission Oll Flow – Diagrams and Operations
Traubleshooting – Transmission/Torque Converter and
HydraulicSyslem
Diagram Service Transmission Removal, Controls
Transmission ControlVaIve
TorqueConverter
Charging PumpR25586
DriveShails
CrawlerTransrnission
Transmission Final Drives
Transmission Brakes
70 SERIES-BRAKES
Brakes – See Section 6027
Brake Pedals and Linkage,ParkingBrake
80 SERIES—ELECTRICAL ‘
Wiring Diagram
Troubleshooting
Battery
Starter and Staner Solenoid
Alternator
90 SERIES – MOUNTED EQUIPMENT
Loader
Power Tilt Dozer Power Angle-Tilt-Pitch (ATP) Dozer
Field Removal/Installation of ATP Dozer
Blade for Transport- Supplement 1-
WSA Hyster Winch
Ripper

Please Note:

⦁ This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
⦁ Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.