Case IH AXIAL FLOW 5130 6130 7130 Combines Operators Manual – PDF DOWNLOAD

Description

Case IH AXIAL FLOW 5130 6130 7130 Combines Operators Manual

DESCRIPTION:

• This manual contains information concerning the adjustment and maintenance of your new equipment. You have purchased a dependable machine, but only by proper care and operation can you expect to receive the performance and long service built into this equipment. Please have all operators read this manual carefully and keep it available for ready reference. Your CASE IH
• AGRICULTURE dealer will instruct you in the general operation of your new equipment. (Refer to the ‘Delivery Report’ at the back of this manual.) Your dealer’s staff of factory-trained service technicians will be glad to answer any questions that may arise regarding the operation of your machine. Your CASE IH AGRICULTURE dealer carries a complete line of genuine CASE IH AGRICULTURE service parts. These parts are manufactured and carefully inspected to insure high quality and accurate fitting of any necessary replacement parts.
• Be prepared to give your dealer the model and product identification number of your new equipment when ordering parts. Locate these numbers now and record them below. Refer to the ‘General Information’ section of this manual for the location of the model and product identification numbers of your machine.

IMAGES:

CASE IH AXIAL FLOW 5130 6130 7130 COMBINES OPERATORS MANUAL – PDF DOWNLOAD:

TABLE OF CONTENTS:

1 GENERAL INFORMATION
Note to the Owner 1-1
Declaration of conformity 1-2
EC Declaration of Conformity 1-3
Intended use 1-5
Manual scope 1-6
Foreword – Ecology and the environment 1-8
Biodiesel fuel – Biodiesel fuels 1-9
Selective catalytic reduction (SCR) system 1-11
Engine tampering 1-17
Airborne noise emission 1-17
Electro-Magnetic Compatibility (EMC) 1-17
Vehicle vibration levels 1-17
Product identification 1-18
Machine orientation 1-19
International symbols 1-20
2 SAFETY INFORMATION
Basic operating safety rules 2-1
Machine safety 2-6
Do Not Operate hang tag 2-7
Safety signs 2-8
SCR Safety signs 2-28
Informational Decals 2-30
Machine safety 2-43
Protective devices 2-44
Fire prevention 2-46
Battery safety 2-47
Maintenance Safety 2-48
Fuel storage 2-48
Wheels and tires 2-49
Before starting the engine 2-50
Operator’s seat 2-50
Unclogging the machine 2-50
3 CONTROLS/INSTRUMENTS
ACCESS TO OPERATOR’S PLATFORM
Operator’s Platform 3-1
Engine, Rear Platform Access 3-5
OPERATOR’S SEAT
Operator seat — Overview 3-7
Seat belt – Overview — Overview 3-9
INSTRUCTOR’S SEAT
Instructional seat — Overview 3-11
FORWARD CONTROLS
Instrument panel — Tier 4a/Euro 5 emissions equipped machine 3-12
Gauges — Tier four emission equipped machine 3-13
Indicator lamp and alarm test 3-15
Warning indicators 3-16
Custom LCD display 3-19
Selective catalytic reduction (SCR) system 3-23
Foot controls 3-26
Steering column 3-27
RIGHT-HAND SIDE CONTROLS
Propulsion control lever 3-30
Right-hand console 3-35
Gear shifting system 3-45
Cab Layout 3-46
Cab Door 3-47
REARWARD CONTROLS
Rear window 3-48
OVERHEAD CONTROLS
Front overhead controls 3-48
Radio or audio system 3-52
Automatic temperature control system 3-53
Interior lamps 3-56
SHIELD
Side Panel operation 3-57
Side Panel adjustment 3-61
Service Lamps 3-62
4 OPERATING INSTRUCTIONS
COMMISSIONING THE UNIT
Before starting the engine 4-1
STARTING THE UNIT
Normal engine starting 4-2
Stopping the engine 4-5
Cold temperature operation 4-6
5 TRANSPORT OPERATIONS
ROAD TRANSPORT
Transport safety 5-1
LIGHTING SYSTEM – Overview 5-2
Preparing for road transport 5-4
PREPARING FOR ROAD TRANSPORT
Preparing for road transport 5-7
Road travel 5-10
Signal plates and lights – adjustment 5-13
Front road lighting – adjustment 5-16
SHIPPING TRANSPORT
Tie downs for shipping 5-17
RECOVERY TRANSPORT
Towing 5-18
Disabled machine – Releasing the parking brake 5-20
6 WORKING OPERATIONS
COMBINE SETUP
Error screen 6-1
Monitor screens 6-3
Hours screen 6-4
Area change 6-5
Grain scan change 6-6
Header sensitivity 6-7
Header type/cutting type 6-8
Combine info 6-11
Set up screens 6-14
CALIBRATIONS
Concave 6-21
Tailings volume 6-22
Header height 6-23
Header tilt 6-26
Upper Sieve 6-29
Lower Sieve 6-31
Reel drive 6-33
Diagnostic menu 6-35
Alarm and Abort screen 6-42
CXCM Error codes 6-43
Alarms 6-43
Connecting a header
Connecting a header 6-46
Remove header 6-50
Adapter adjustment 6-53
COMBINE SETUP
General field operation 6-54
Threshing speed 6-58
AFX Rotor — Overview and initial settings 6-59
ST Rotor — Overview and initial settings 6-65
Header Height Control
Header operating variables 6-71
Return to Cut Mode 6-75
Auto Height mode 6-77
Pressure Float mode 6-78
Header Tilt Control
Manual mode 6-79
Auto tilt mode 6-80
Level mode 6-80
Reel control
Reel speed 6-80
Reel position 6-82
Monitor Operation
Shaft Speed 6-83
Harvest Screen 6-84
Feeder
Feeder Reverser 6-85
Automatic Feeder cutoff 6-85
Rock Trap 6-86
Feeder Cradle adjustment 6-88
Feeding
Two speed gear box – Adjustment 6-90
Feeder chain — Adjustment 6-91
Feeder drum — Adjustment fore/aft 6-93
Ride control — Accumulator 6-95
Automatic Feeder cutoff 6-97
Unloading
Unloading 6-98
Threshing and separation
Threshing and separating overview 6-99
Rotor — Overview 6-100
Rotor — Unplugging 6-102
Concaves
Concaves Overview 6-103
Concaves – Adjustment 6-106
Concave – Removal 6-111
Concave – Installation 6-113
Grates
Grates – Overview 6-114
Grates – Removal 6-115
Grates – Installation 6-116
Cage Transport Vanes 6-118
Threshing, separation and cleaning 6-120
Cleaning system and lower frame
Cleaning system and lower frame – Overview 6-121
Auger bed 6-122
Cleaning fan – Overview 6-123
Sieves
Chaffer sieve — Overview 6-125
Chaffer sieve — Removal 6-128
Chaffer sieve — Installation 6-131
Lower sieve — Overview 6-133
Lower sieve — Removal 6-135
Lower sieve — Installation 6-138
Grain storage/unloading
Grain handling and material distribution 6-140
Clean out doors 6-142
Clean grain elevator drive 6-145
Cross Auger 6-146
Unloader drive chains 6-146
Residue handling
Chaff spreader 6-147
Straw chopper 6-150
Chopper blade – Blade replacement 6-154
Counter knives – Removal 6-155
Losses
Threshing 6-157
Seed loss 6-162
Quick stop 6-164
Threshing and separation – Troubleshooting 6-165
7 MAINTENANCE
GENERAL INFORMATION
Torque charts – Minimum tightening torques for normal assembly 7-1
Grease decal reference – Engine platform 7-5
Grease decal reference – left hand side 7-7
Grease decal reference – right-hand side 7-10
Drive and gear Chain drive – Basic instructions – Lubrication 7-14
Air reservoir 7-16
Battery – Safety rules 7-17
Battery access and service 7-18
Cab power connections 7-21
Fuses and relays location 7-22
MAINTENANCE CHART
Capacities 7-27
Lubrication and oil specifications — Recommended operating temperature range 7-30
Engine oil 7-31
Lubrication schedule
Lubrication schedule 7-32
ENGINE
Checking the engine oil level 7-37
Changing engine oil 7-38
Engine oil filter 7-39
Cooling fan — Drive belt 7-40
Air conditioning compressor drive belt — Removal, installation and adjustment 7-42
Cooling System
Engine cooling system 7-43
Engine coolant replace 7-45
Intercooler 7-46
Stationary air screen 7-47
Fuel system
Overview 7-50
Fuel filter — Replacement 7-51
Additional fuel prefilter with water separator — Drain sediment bowl 7-54
Additional fuel prefilter with water separator — Filter replacement 7-55
Bleed air from the fuel system 7-57
Selective catalytic reduction (SCR) system
Selective catalytic reduction (SCR) system 7-59
DEF/AdBlue® in-line filter 7-60
Engine air filter system
Air filter 7-61
Front axle
Transmission oil 7-65
Change planetary final drives oil 7-67
Hydraulic system
Hydraulic oil reservoir — fluid level make up 7-68
Hydraulic oil reservoir — Change fluid 7-70
Hydraulic filter(s) 7-72
Propulsion system bleeding 7-74
Hydraulic system — Bleeding 7-76
Power Take Off (PTO)
PTO Gearbox 7-77
Feeder and cleaning fan gear case
Feeder and cleaning fan gear case 7-78
Two speed feeder gear case – If equipped 7-80
Feeder
Feeder drive belt belt – tracking 7-81
Feeder drive belt belt – removal 7-83
Feeder drive belt belt – installation 7-85
Feeder jackshaft drive — Removal 7-86
Feeder jackshaft drive — installation and adjustment 7-88
Feeder conveyor chain – removal and installation 7-90
Feeder conveyor chain – adjustment 7-91
Rock trap drive — Removal and installation 7-92
Rock trap drive — Adjustment 7-93
Separator drive
Separator drive belt – removal 7-95
Separator drive belt – installation 7-97
Cleaning fan
Cleaning fan drive — removal 7-100
Cleaning fan drive — installation 7-102
Cleaning fan drive — Adjustment 7-103
Cleaning fan jackshaft belt — Removal 7-104
Cleaning fan jackshaft belt – installation and adjustment 7-107
Rotor
Rotor gearbox oil 7-110
Rotor — Front bearing 7-111
Rotor drive belt – adjustment 7-112
Rotor drive belt — replacement 7-114
Straw chopper
Straw chopper drive 7-118
Straw chopper drive belt – removal, installation and adjustment 7-119
Grain tank filling system
Clean grain elevator drive — belt – removal 7-121
Clean grain elevator drive — belt – installation 7-123
Clean grain elevator drive chain – removal, installation and adjustment 7-125
Clean grain elevator chain – removal and installation 7-126
Clean grain elevator chain – slip clutch adjustment 7-127
Clean grain elevator chain — Adjustment 7-128
Inclined auger 7-129
Unloading
Unloading tube gearbox oil 7-130
Unloading elbow 7-131
Unloading drive chain – removal 7-132
Unloading drive chain – installation and adjustment 7-132
Unloading drive chain – Shear bolt 7-133
Grain tank unloading drive belt – Drive belt removal 7-134
Grain tank unloading drive belt – installation 7-137
Grain tank unloading drive belt – adjust guides 7-139
Tailings
Tailings elevator conveyor drive chain – removal, installation and adjustment 7-142
Tailings elevator conveyor chain – removal and installation 7-143
Tailings elevator conveyor chain – adjustment 7-144
Residue spreader
Straw spreader drive — belt – removal 7-145
Straw spreader drive belt – installation and adjustment 7-148
Straw spreader drive two speed drive pulley belt – adjustment 7-150
Lighting system
Roof lights 7-152
Flood and work lamps Bulb replacement 7-156
Turn signal/Hazard light bulb replacement 7-157
Road lamp – replacement 7-158
Road lamp – adjustment 7-159
Work lamps – Bulb replacement 7-161
Side marker lights – Bulb replacement 7-162
Front turn signal and clearance lights – Bulb replacement 7-163
STORAGE
Preparation for storage 7-164
Removal from storage 7-165
8 TROUBLESHOOTING
FAULT CODE RESOLUTION
Automatic Feeder cutoff 8-1
CXCM Error codes 8-2
A-Post Error Codes 8-6
Electronic engine error codes 8-8
9 SPECIFICATIONS
Overall Dimensions 9-1
General specifications 9-4
Travel speeds – approximate 9-8
Electrical specifications 9-10
Tire pressure 9-11
Front wheel tread settings 9-12
Steering axle 9-17
Rear wheel torque 9-20
Powered rear axle 9-21
Toe-in adjustment 9-22
Tire selection chart 9-23
Tire selection chart 9-27
Maximum header size 9-31
10 ACCESSORIES
Air compressor 10-1
11 FORMS AND DECLARATIONS
Delivery report – Owner Copy 11-1
Delivery report – Dealer Copy 11-3
Service record – 1st 50 Hour, Customer Copy 11-5
Service record – 1st 50 Hour, Dealer Copy 11-7

FILE DETAILS:

Case IH Series Tractor Operators Manual CD
Size: 30.9 MB
Fomat: PDF
Language: English
Brand: Case IH
Type of machine: Tractor
Type of document: Operators Manual

PLEASE NOTE:

⦁ This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
⦁ The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
⦁ Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer