Case WX145 WX165 & WX185 Tier 3 Wheeled Hydraulic Excavators Operator’s Manual 87590052 – PDF DOWNLOAD

Description

Case WX145 WX165 & WX185 Tier 3 Wheeled Hydraulic Excavators Operator’s Manual 87590052 – PDF DOWNLOAD

DESCRIPTION:

Case WX145 WX165 & WX185 Tier 3 Wheeled Hydraulic Excavators Operator’s Manual 87590052 – PDF DOWNLOAD

FOREWORD :

The current Operator’s Manual is the user’s guide for correct run-in, use and maintenance of the machine. Carefully read this Operator’s Manual and store it in the cab for quick location and reference. Instructions concerning safety, operation and maintenance have been developed to permit safe service and operation of this machine.

• In the event of queries or suggestions relevant to your machine do not hesitate to address to your Dealer. Dealers have qualified and trained personnel at disposal as well as Original Spares, means and equipment suitable to carry out all necessary maintenance.
• Do not use this machine for any applications or purposes other than those described in this Manual. If you use this machine for duties involving the use of attachments, accessories, or special tools, consult your Dealer to make sure that the adaptations or modifications carried out are in conformity with the machine’s technical specifications and with current regulations on safety. Any modifications or adaptations which are not approved by the Manufacturer may invalidate the machine’s original conformity with safety requirements.

TABLE OF CONTENTS:

Case WX145 WX165 & WX185 Tier 3 Wheeled Hydraulic Excavators Operator’s Manual 87590052 – PDF DOWNLOAD

1 – INTRODUCTION, SAFETY, PLATES AND DECALS
2 – CONTROLS AND INSTRUMENTS
3 – OPERATING THE MACHINE
4 – SUPPLIES AND SERVICE CHART
5 – TROUBLESHOOTING
6 – STORAGE
7 – ACCESSORIES
8 – DATA AND TECHNICAL SPECIFICATIONS
9 – ALPHABETICAL INDEX

SECTION 1
INTRODUCTION, SAFETY, PLATES AND DECALS ……………………………………………………………………… 1-1
FOREWORD……………………………………………………………………………………………………………………………. 1-1
SAFETY INSTRUCTIONS…………………………………………………………………………………………………………. 1-2
GENERAL SAFETY INSTRUCTIONS………………………………………………………………………………………. 1-2
DESIGNATED USE ……………………………………………………………………………………………………………….. 1-3
NOISE LEVELS …………………………………………………………………………………………………………………….. 1-4
LEVEL OF VIBRATIONS TRANSMITTED TO THE OPERATOR…………………………………………………. 1-5
BEFORE OPERATING THE MACHINE ……………………………………………………………………………………. 1-6
OPERATING THE MACHINE………………………………………………………………………………………………….. 1-8
TRAVEL……………………………………………………………………………………………………………………………… 1-10
TRAVELLING ON PUBLIC ROADS ……………………………………………………………………………………….. 1-12
JOB SITE OPERATION………………………………………………………………………………………………………… 1-16
PARKING THE MACHINE…………………………………………………………………………………………………….. 1-18
LOADING THE MACHINE ON A TRAILER……………………………………………………………………………… 1-19
MACHINE TRANSPORT ………………………………………………………………………………………………………. 1-20
UNLOADING THE MACHINE FROM A TRAILER…………………………………………………………………….. 1-21
MAINTENANCE AND ADJUSTMENTS…………………………………………………………………………………… 1-22
PREVENTION OF FIRE OR EXPLOSIONS…………………………………………………………………………….. 1-25
PREVENTION OF BURNS……………………………………………………………………………………………………. 1-26
PRECAUTIONS FOR WASTE DISPOSAL………………………………………………………………………………. 1-27
MAIN COMPONENTS …………………………………………………………………………………………………………….. 1-28
PLACING BOOM ATTACHMENT…………………………………………………………………………………………… 1-28
MONOBOOM ATTACHMENT ……………………………………………………………………………………………….. 1-29
COMPONENTS IDENTIFICATION PLATES………………………………………………………………………………. 1-32
MACHINE …………………………………………………………………………………………………………………………… 1-32
ENGINE……………………………………………………………………………………………………………………………… 1-32
CAB …………………………………………………………………………………………………………………………………… 1-33
CE-MARK …………………………………………………………………………………………………………………………… 1-33
PUMP ………………………………………………………………………………………………………………………………… 1-34
AXLES ……………………………………………………………………………………………………………………………….. 1-34
CONTROL VALVE……………………………………………………………………………………………………………….. 1-34
DECALS………………………………………………………………………………………………………………………………… 1-35
NOISE LEVEL DECAL …………………………………………………………………………………………………………. 1-35
POSITION OF DECALS ……………………………………………………………………………………………………….. 1-36
HAND SIGNALS …………………………………………………………………………………………………………………….. 1-43
SECTION 2
CONTROLS AND INSTRUMENTS……………………………………………………………………………………………….. 2-1
SWITCHES AND PUSH-BUTTONS……………………………………………………………………………………………. 2-1
“BUZZER”: ACOUSTIC WARNING SIGNAL……………………………………………………………………………… 2-7
CONTROLS AND PEDALS ……………………………………………………………………………………………………….. 2-8
MULTI-FUNCTION DISPLAY …………………………………………………………………………………………………… 2-11
OPERATING MODE…………………………………………………………………………………………………………….. 2-17
MAIN MENU ……………………………………………………………………………………………………………………….. 2-18
CONDITIONS OF USE…………………………………………………………………………………………………………. 2-19
INDEX
DISPLAY SETTING, MAIN MENU …………………………………………………………………………………………. 2-20
CONTRAST………………………………………………………………………………………………………………………… 2-21
BRIGHTNESS …………………………………………………………………………………………………………………….. 2-22
TIME ………………………………………………………………………………………………………………………………….. 2-23
UNITS ………………………………………………………………………………………………………………………………… 2-26
SYMBOLS ………………………………………………………………………………………………………………………….. 2-28
STARTER SWITCH………………………………………………………………………………………………………………… 2-29
RADIO ………………………………………………………………………………………………………………………………….. 2-31
CAB ……………………………………………………………………………………………………………………………………… 2-32
ENTRY AND EXIT……………………………………………………………………………………………………………….. 2-32
DOOR OPENING ………………………………………………………………………………………………………………… 2-32
DOOR CLOSING…………………………………………………………………………………………………………………. 2-33
SIDE WINDOW……………………………………………………………………………………………………………………. 2-33
FRONT WINDOW………………………………………………………………………………………………………………… 2-34
EMERGENCY EXIT……………………………………………………………………………………………………………… 2-35
WINDSCREEN WIPER AND WASHER………………………………………………………………………………….. 2-35
FLOODLAMPS ……………………………………………………………………………………………………………………. 2-36
DOCUMENTS STORAGE BOX, FIRST-AID KIT, WARNING TRIANGLE AND
FIRE-EXTINGUISHER …………………………………………………………………………………………………………. 2-37
SUNBLIND………………………………………………………………………………………………………………………….. 2-37
CAB LIGHTING …………………………………………………………………………………………………………………… 2-38
AUXILIARY SOCKET …………………………………………………………………………………………………………… 2-38
STEERING COLUMN…………………………………………………………………………………………………………… 2-39
VENTILATION, HEATING AND AIR CONDITIONING (OPTIONAL)………………………………………………. 2-40
VENTILATION (air from outside) ……………………………………………………………………………………………. 2-40
HEATING……………………………………………………………………………………………………………………………. 2-42
AIR CONDITIONING (OPTIONAL)…………………………………………………………………………………………. 2-43
SERVICE AND PARKING BRAKES………………………………………………………………………………………….. 2-45
SERVICE BRAKE………………………………………………………………………………………………………………… 2-45
PARKING BRAKE ……………………………………………………………………………………………………………….. 2-46
OPERATOR’S SEAT ………………………………………………………………………………………………………………. 2-47
OPERATOR’S SEAT WITH PNEUMATIC SUSPENSION …………………………………………………………. 2-47
SEAT BELT …………………………………………………………………………………………………………………………… 2-52
SECTION 3
OPERATING THE MACHINE……………………………………………………………………………………………………….. 3-1
GENERAL INSTRUCTIONS………………………………………………………………………………………………………. 3-1
BEFORE OPERATING THE MACHINE ……………………………………………………………………………………. 3-1
OPERATING THE MACHINE………………………………………………………………………………………………….. 3-1
RUNNING-IN PERIOD …………………………………………………………………………………………………………… 3-2
AFTER DAILY OPERATION – PARKING………………………………………………………………………………….. 3-3
START-UP………………………………………………………………………………………………………………………………. 3-4
START-UP IMMOBILIZER ……………………………………………………………………………………………………… 3-4
START-UP……………………………………………………………………………………………………………………………. 3-9
ASSISTED STARTING (JUMP-STARTING) ……………………………………………………………………………. 3-11
ENGINE SHUT OFF …………………………………………………………………………………………………………….. 3-13
TRAVEL………………………………………………………………………………………………………………………………… 3-14
BEFORE STARTING THE TRAVEL……………………………………………………………………………………….. 3-14
BASIC POSITION………………………………………………………………………………………………………………… 3-14
INDEX
BASIC SETTING …………………………………………………………………………………………………………………. 3-16
TRAVEL……………………………………………………………………………………………………………………………… 3-18
GEARBOX – GEAR CHANGE ……………………………………………………………………………………………….. 3-21
TRAVEL WITH LOAD APPLIED TO CRANING HOOK……………………………………………………………… 3-23
FLOATING AXLE BLOCKING AND UNBLOCKING………………………………………………………………….. 3-24
WORKING OPERATION …………………………………………………………………………………………………………. 3-25
SAFETY INSTRUCTIONS…………………………………………………………………………………………………….. 3-25
BEFORE BEGINNING THE WORK………………………………………………………………………………………… 3-26
HOLDING AND RELEASING THE UPPER STRUCTURE SLEW ………………………………………………. 3-31
POWER BOOST FUNCTION – POWER BOOST……………………………………………………………………… 3-37
LEVELLING MODE ……………………………………………………………………………………………………………… 3-39
HYDRAULIC DAMPING ……………………………………………………………………………………………………….. 3-41
STABILIZATION OF THE MACHINE………………………………………………………………………………………. 3-43
WORKING WITH STANDARD BUCKET OR CLAMSHELL……………………………………………………….. 3-46
WORKING STAGES…………………………………………………………………………………………………………….. 3-48
OPERATING THE MACHINE WITH COLD WEATHER……………………………………………………………….. 3-51
COLD START – PREHEATING………………………………………………………………………………………………. 3-52
OPERATING THE MACHINE WITH HOT WEATHER …………………………………………………………………. 3-54
MACHINE RECOVERY AND TOWING……………………………………………………………………………………… 3-55
SECURE THE MACHINE ……………………………………………………………………………………………………… 3-56
WORKING ATTACHMENT………………………………………………………………………………………………………. 3-59
PLACING BOOM ATTACHMENT…………………………………………………………………………………………… 3-60
WORKING ATTACHMENT WITH OFF-SET BOOM …………………………………………………………………. 3-63
BUCKET …………………………………………………………………………………………………………………………….. 3-64
BUCKET DISASSEMBLY AND ASSEMBLY……………………………………………………………………………. 3-66
BUCKETS TEETH – CHANGE……………………………………………………………………………………………….. 3-67
SECTION 4
SUPPLIES AND SERVICE CHART………………………………………………………………………………………………. 4-1
SUPPLIES AND SERVICE CHART…………………………………………………………………………………………….. 4-1
FUEL……………………………………………………………………………………………………………………………………. 4-2
HYDRAULIC OIL …………………………………………………………………………………………………………………… 4-3
SAFETY INSTRUCTIONS…………………………………………………………………………………………………………. 4-5
WORKING HOURS / INTERVALS ……………………………………………………………………………………………… 4-6
MAINTENANCE INTERVALS CHART ………………………………………………………………………………………… 4-7
CHECKS BEFORE START-UP AND BEFORE EACH WORKING SHIFT (10 HOURS) …………………… 4-10
MACHINE GENERAL INSPECTION ………………………………………………………………………………………. 4-10
SERVICE BRAKE………………………………………………………………………………………………………………… 4-11
PARKING BRAKE ……………………………………………………………………………………………………………….. 4-11
UPPER STRUCTURE HOLDING BRAKE……………………………………………………………………………….. 4-12
LIGHTS………………………………………………………………………………………………………………………………. 4-12
CONTROLS AND LAMPS OPERATION…………………………………………………………………………………. 4-12
ENGINE OIL – LEVEL…………………………………………………………………………………………………………… 4-13
HYDRAULIC OIL TANK – LEVEL …………………………………………………………………………………………… 4-13
FUEL TANK – LEVEL……………………………………………………………………………………………………………. 4-15
COOLING SYSTEM LIQUID – LEVEL …………………………………………………………………………………….. 4-17
SCREEN WASHER LIQUID – LEVEL……………………………………………………………………………………… 4-19
WORKING ATTACHMENT – GREASING………………………………………………………………………………… 4-20
OFF-SET BOOM – GREASING ……………………………………………………………………………………………… 4-21
INDEX
TYRES – PRESSURE CHECK ………………………………………………………………………………………………. 4-22
TYRES – NUTS TIGHTENING……………………………………………………………………………………………….. 4-24
WEEKLY SERVICE (50 HOURS)……………………………………………………………………………………………… 4-25
CAB AIR FILTER – CLEANING ……………………………………………………………………………………………… 4-25
AIR FILTER – CLEANING……………………………………………………………………………………………………… 4-26
AIR INTAKE LINE – CHECK………………………………………………………………………………………………….. 4-28
MULTI-COOLER – CLEANING………………………………………………………………………………………………. 4-28
FUEL SYSTEM – AIR BLEEDING AND WATER DRAINING ……………………………………………………… 4-29
FUEL FILTER/S – WATER DRAINING ……………………………………………………………………………………. 4-32
SLEWING GEARBOX – OIL LEVEL ……………………………………………………………………………………….. 4-33
BATTERIES – LEVEL – CHARGE CHECK AND CLAMPS TIGHTENING…………………………………….. 4-34
SLEWING BEARING CUPS AND AXLE FLOATING PINS – GREASING…………………………………….. 4-37
QUICK COUPLER – GREASING……………………………………………………………………………………………. 4-38
MONTHLY SERVICE (250 HOURS) …………………………………………………………………………………………. 4-39
ENGINE OIL FILTER – CHANGE …………………………………………………………………………………………… 4-39
FUEL FILTER/S – CHANGE ………………………………………………………………………………………………….. 4-40
HYDRAULIC OIL RETURN FILTER – CHANGE ………………………………………………………………………. 4-41
STEERING AXLE – OIL LEVEL ……………………………………………………………………………………………… 4-42
TRAVEL GEARBOXES – OIL LEVEL ……………………………………………………………………………………… 4-43
RIGID AXLE AND GEARBOX – OIL LEVEL…………………………………………………………………………….. 4-44
AIR CONDITIONING SYSTEM ……………………………………………………………………………………………… 4-45
BLADE AND STABILIZERS JOINTS, CARDAN SHAFT, STEERING TRUNNION PINS –
GREASING…………………………………………………………………………………………………………………………. 4-46
FLOATING AXLE LOCKING CYLINDERS CONTACT FACES – LUBRICATION ………………………….. 4-47
SERVICE EVERY 12 MONTHS (500 HOURS)…………………………………………………………………………… 4-48
ENGINE REVOLUTIONS SENSOR – CLEANING ……………………………………………………………………. 4-48
DRIVE BELTS – CHECK……………………………………………………………………………………………………….. 4-49
ENGINE OIL – CHANGE……………………………………………………………………………………………………….. 4-50
SLEWING BEARING – SCREW TIGHTENING CHECK…………………………………………………………….. 4-51
SLEWING BEARING TEETH – GREASING …………………………………………………………………………….. 4-52
SLEWING GEARBOX – SCREWS TIGHTENING CHECK…………………………………………………………. 4-52
SERVICE AFTER 1000 HOURS ………………………………………………………………………………………………. 4-53
CAB AIR FILTER – CHANGE ………………………………………………………………………………………………… 4-53
WINDSCREEN BLADES – CHANGE ……………………………………………………………………………………… 4-53
ENGINE BRACKETS – SCREWS TIGHTENING CHECK………………………………………………………….. 4-54
ENGINE BELT TENSIONER – CHECK …………………………………………………………………………………… 4-54
AIR FILTER – REPLACEMENT OF MAIN FILTER ELEMENT AND OF
SAFETY ELEMENT……………………………………………………………………………………………………………… 4-55
HYDRAULIC SYSTEM BLEEDING VALVE – CHANGE…………………………………………………………….. 4-56
STEERING AXLE – OIL CHANGE………………………………………………………………………………………….. 4-56
RIGID AXLE AND GEARBOX – OIL CHANGE…………………………………………………………………………. 4-58
SERVICE BRAKE – PLATES CHECK …………………………………………………………………………………….. 4-60
PILOT CONTROL FILTER – CHANGE……………………………………………………………………………………. 4-61
AIR CONDITIONING SYSTEM – CLEANING AND OPERATION CHECK –
COMPRESSOR BELT CHANGE …………………………………………………………………………………………… 4-61
SERVICE AFTER 3000 HOURS ………………………………………………………………………………………………. 4-65
HYDRAULIC OIL TANK – CLEANING AND OIL CHANGE ………………………………………………………… 4-65
HYDRAULIC SYSTEM – AIR BLEEDING………………………………………………………………………………… 4-67
ENGINE – CHECK AND ADJUSTMENT OF VALVES CLEARANCE ………………………………………….. 4-67
COOLING SYSTEM LIQUID – CHANGE…………………………………………………………………………………. 4-68
FUEL TANK – CLEANING …………………………………………………………………………………………………….. 4-69
INDEX
SLEWING GEARBOX – OIL CHANGE……………………………………………………………………………………. 4-70
SERVICE WHEN NECESSARY……………………………………………………………………………………………….. 4-71
MACHINE – CLEANING………………………………………………………………………………………………………… 4-71
WINDSCREEN WIPER – CHECK AND CLEANING………………………………………………………………….. 4-73
DRIVE BELT – CHANGE ………………………………………………………………………………………………………. 4-73
INJECTORS – REPLACEMENT …………………………………………………………………………………………….. 4-74
HYDRAULIC SYSTEM AND TANK – PRESSURE RELEASE…………………………………………………….. 4-74
TYRES – CHANGE ………………………………………………………………………………………………………………. 4-76
SERVICE BRAKE – AIR BLEEDING……………………………………………………………………………………….. 4-78
STEERING ADJUSTMENT …………………………………………………………………………………………………… 4-78
AXLE FLOATING LOCKING CYLINDERS – AIR BLEEDING……………………………………………………… 4-79
FUSES – REPLACEMENT…………………………………………………………………………………………………….. 4-80
BULBS – REPLACEMENT…………………………………………………………………………………………………….. 4-83
BATTERIES – REPLACEMENT……………………………………………………………………………………………… 4-87
BUCKETS TEETH – CHANGE……………………………………………………………………………………………….. 4-88
CLAMSHELL – WEAR CHECK………………………………………………………………………………………………. 4-89
SECTION 5
TROUBLESHOOTING ………………………………………………………………………………………………………………… 5-1
ERRORS INDICATION ON THE DISPLAY……………………………………………………………………………….. 5-2
ENGINE ………………………………………………………………………………………………………………………………….. 5-3
STEERING SYSTEM………………………………………………………………………………………………………………… 5-6
BRAKES SYSTEM……………………………………………………………………………………………………………………. 5-7
SERVICE BRAKE………………………………………………………………………………………………………………….. 5-7
PARKING BRAKE …………………………………………………………………………………………………………………. 5-7
HYDRAULIC SYSTEM ……………………………………………………………………………………………………………… 5-8
TRAVEL………………………………………………………………………………………………………………………………… 5-10
SLEWING ……………………………………………………………………………………………………………………………… 5-11
FLOATING AXLE BLOCKING………………………………………………………………………………………………….. 5-12
STABILIZERS………………………………………………………………………………………………………………………… 5-13
HYDRAULIC HAMMER …………………………………………………………………………………………………………… 5-15
CLAMSHELL BUCKET……………………………………………………………………………………………………………. 5-16
AXLES ………………………………………………………………………………………………………………………………….. 5-17
CENTRALIZED LUBRICATION PUMP ……………………………………………………………………………………… 5-19
HEATING/AIR CONDITIONING SYSTEM………………………………………………………………………………….. 5-21
SYSTEM…………………………………………………………………………………………………………………………….. 5-21
COOLING SYSTEM …………………………………………………………………………………………………………….. 5-22
BLOWER ……………………………………………………………………………………………………………………………. 5-23
SECTION 6
STORAGE …………………………………………………………………………………………………………………………………. 6-1
MACHINE STORAGE…………………………………………………………………………………………………………….. 6-1
ENGINE STORAGE ………………………………………………………………………………………………………………. 6-1
BATTERIES STORAGE …………………………………………………………………………………………………………. 6-2
RECOMMISSIONING THE MACHINE AFTER PROLONGED STORAGE…………………………………….. 6-2
DECOMMISSIONING OF THE MACHINE ………………………………………………………………………………… 6-3
INDEX
SECTION 7
ATTACHMENTS…………………………………………………………………………………………………………………………. 7-1
HYDRAULIC HAMMER…………………………………………………………………………………………………………….. 7-1
HYDRAULIC HAMMER SELECTION……………………………………………………………………………………….. 7-1
SAFETY INSTRUCTIONS………………………………………………………………………………………………………. 7-1
USE OF HYDRAULIC HAMMER……………………………………………………………………………………………… 7-3
HYDRAULIC SHEARS ……………………………………………………………………………………………………………… 7-8
SELECTING THE HYDRAULIC SHEARS…………………………………………………………………………………. 7-8
SAFETY INSTRUCTIONS………………………………………………………………………………………………………. 7-8
USE OF HYDRAULIC SHEARS…………………………………………………………………………………………….. 7-10
HYDRAULIC QUICK COUPLER ………………………………………………………………………………………………. 7-15
SAFETY INSTRUCTIONS…………………………………………………………………………………………………….. 7-15
QUICK ASSEMBLY AND DISASSEMBLY………………………………………………………………………………. 7-17
HANDLING OF LOADS………………………………………………………………………………………………………… 7-19
CLAMSHELL BUCKET……………………………………………………………………………………………………………. 7-20
SAFETY INSTRUCTIONS…………………………………………………………………………………………………….. 7-20
CLAMSHELL BUCKET ASSEMBLY ………………………………………………………………………………………. 7-20
CLAMSHELL BUCKET DISASSEMBLY …………………………………………………………………………………. 7-22
PARAMETERS SETTING …………………………………………………………………………………………………….. 7-23
SWITCHING OVER FROM STANDARD TO CLAMSHELL BUCKET………………………………………….. 7-23
ROTARY CUTTER …………………………………………………………………………………………………………………. 7-25
SAFETY INSTRUCTIONS…………………………………………………………………………………………………….. 7-25
USE OF THE ROTARY CUTTER…………………………………………………………………………………………… 7-26
CRANING HOOK……………………………………………………………………………………………………………………. 7-30
SAFETY INSTRUCTIONS…………………………………………………………………………………………………….. 7-30
USE OF THE CRANING HOOK…………………………………………………………………………………………….. 7-30
OVERLOAD WARNING SYSTEM…………………………………………………………………………………………….. 7-31
BREAK PROTECTION VALVES ………………………………………………………………………………………………. 7-33
REAR FLOODLAMPS …………………………………………………………………………………………………………….. 7-34
ROTARY LIGHT …………………………………………………………………………………………………………………….. 7-35
SINGLE LIGHT……………………………………………………………………………………………………………………. 7-35
DOUBLE LIGHT ………………………………………………………………………………………………………………….. 7-35
SWITCHING ON AND OFF …………………………………………………………………………………………………… 7-35
FUEL TRANSFER PUMP………………………………………………………………………………………………………… 7-36
CAB PROTECTIONS………………………………………………………………………………………………………………. 7-38
BLADE PROTECTION…………………………………………………………………………………………………………….. 7-38
TRANSPORT BRACKET FOR CLAMSHELL……………………………………………………………………………… 7-38
CENTRALIZED LUBRICATION………………………………………………………………………………………………… 7-39
SAFETY INSTRUCTIONS…………………………………………………………………………………………………….. 7-39
OPERATION……………………………………………………………………………………………………………………….. 7-39
MANUAL FILLING PUMP……………………………………………………………………………………………………… 7-42
MOTORIZED FILLING PUMP ……………………………………………………………………………………………….. 7-43
SECTION 8
DATA AND TECHNICAL SPECIFICATIONS …………………………………………………………………………………. 8-1
DIMENSIONS – OPERATING WEIGHTS…………………………………………………………………………………….. 8-1
WX 145 MODELS………………………………………………………………………………………………………………….. 8-1
INDEX
WX 165 MODELS………………………………………………………………………………………………………………….. 8-4
WX 185 MODELS………………………………………………………………………………………………………………….. 8-7
DIGGING PERFORMANCE ………………………………………………………………………………………………………. 8-9
WX 145 MODELS………………………………………………………………………………………………………………….. 8-9
WX 165 MODELS………………………………………………………………………………………………………………… 8-14
WX 185 MODELS………………………………………………………………………………………………………………… 8-19
LIFTING CAPACITIES…………………………………………………………………………………………………………….. 8-23
HYDRAULIC SYSTEM ……………………………………………………………………………………………………………. 8-24
PUMPS………………………………………………………………………………………………………………………………. 8-24
CYLINDERS (ø for stroke)…………………………………………………………………………………………………….. 8-24
SLEWING ……………………………………………………………………………………………………………………………… 8-24
TRAVEL………………………………………………………………………………………………………………………………… 8-24
TYRES……………………………………………………………………………………………………………………………….. 8-25
BRAKES ……………………………………………………………………………………………………………………………….. 8-25
STEERING…………………………………………………………………………………………………………………………….. 8-25
POWER STEERING…………………………………………………………………………………………………………….. 8-25
ELECTRICAL SYSTEM…………………………………………………………………………………………………………… 8-26
BUCKETS……………………………………………………………………………………………………………………………… 8-26
BUCKETS – WX 145…………………………………………………………………………………………………………….. 8-26
BUCKETS – WX 165…………………………………………………………………………………………………………….. 8-26
BUCKETS – WX 185…………………………………………………………………………………………………………….. 8-26
TIGHTENING TORQUES………………………………………………………………………………………………………… 8-27
CENTRALIZED LUBRICATION PUMP (OPTIONAL)…………………………………………………………………… 8-27
FUEL SYSTEM………………………………………………………………………………………………………………………. 8-27
ENGINE ………………………………………………………………………………………………………………………………… 8-28
SECTION 9
ALPHABETICAL INDEX……………………………………………………………………………………………………………… 9-1

IMAGES PREVIEW OF THE MANUAL:

CASE WX145 WX165 & WX185 TIER 3 WHEELED HYDRAULIC EXCAVATORS OPERATOR’S MANUAL 87590052 – PDF DOWNLOAD:

PLEASE NOTE:

• This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
• This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
• Require some other service manual or have any queries: please WRITE to us at [email protected]

S.V