Cat Bucyrus 2810 Drum Miner Operator’s & Maintenance Manual BI000234 – PDF DOWNLOAD (Section 1 Only)

Description

Cat Bucyrus 2810 Drum Miner Operator’s & Maintenance Manual BI000234 – PDF DOWNLOAD

FILE DETAILS:

Cat Bucyrus 2810 Drum Miner Operator’s & Maintenance Manual BI000234 – PDF DOWNLOAD

Language : English
Pages : 117
Downloadable : Yes
File Type : PDF

TABLE OF CONTENTS:

Cat Bucyrus 2810 Drum Miner Operator’s & Maintenance Manual BI000234 – PDF DOWNLOAD

– OPERATING PROCEDURE-RECOMMENDED STEPS TO FOLLOW 1-1
– MOTOR IDENTIFICATION 1-2
– AUXILIARY CONTROLLER ASSEMBLY 1-3
– AUXILIARY CONTROLLER WIRING 1-4
– MANUAL MODE OPERATION 1-5, 1-6
– NOTES AND COMMENTS 1-7
– I S TRAM SWITCH WIRING 1-8
– TRACTION CASE 1-9
– TRACTION CASE WIRING 1-10
– I S TRAM INTERFACE BOX TERMINALS 1-11
– SCHEMATIC – TRAM CIRCUIT MANUAL – RADIO 1-12
I S TRAM VOLTAGE CHECKS 1-13
– TRAM DRIVE VOLTAGE ADJUSTMENT 1-14
– VOLTAGE/REF GRAPHS 1-15
– SETTING TRAM VOLTAGES – CLEAN UP – SUMP 1-16
– TRAM INTERFACE BOX ADJUSTMENT LOCATIONS 1-17
– 6 SCR TRAM DRIVE INSTALLATION – TROUBLESHOOTING 1-18
– 6 SCR DIAGNOSTIC PANEL 1-19
– FIELD INSTALLATION FOR EIMCO TRAM DRIVES 1-20, 1-21
– TROUBLESHOOTING PROCEDURES 1-22
NOTES AND COMMENTS 1-23
– MAIN CONTROLLER CASE ASSEMBLY 1-24
SWING PANEL 1-25
CONTACTOR PANEL 1-26
– NOTES AND COMMENTS 1-27
– CONTACTORS 1-28, 1-29
– CONTACTOR TROUBLESHOOTING 1-30, 1-31
– INSTANTANEOUS OVERLOAD ADJUSTMENT LOCATIONS 1-32
– THERMAL OVERLOAD RELAYS 1-33
– TIMERS 1-3 4
– NOTES AND COMMENTS 1-35
– RADIO BASICS 1-36
– RADIO COMPONENTS 1-37
– RADIO TRANSMITTER OPERATION 1-38, 1-39
– NOTES AND COMMENTS 1-40
– RADIO RECEIVER 1-41
– RADIO RELAY BOX – TERMINAL CONNECTIONS 1-42
– RADIO RELAY BOX SCHEMATIC 1-43
– I S SOLENOID COMPONENTS 1-44
– I S SOLENOID CIRCUIT 1-45
– I S SOLENOID VOLTAGE CHECKS 1-46
– XjP SOLENOID CIRCUIT – WIRING AND VOLTAGE CHECKS 1-47
– SCHEMATICS – POWER, CONTROL 1-48, 1-49
– NOTES AND COMMENTS 1-50
– ELECTRICAL CIRCUIT EXPLANATION – RADIO 1-51 THRU 1-92
– ELECTRICAL CIRCUIT EXPLANATION – MANUAL 1-93 THRU 1-128
– NOTES AND COMMENTS 1-129

DESCRIPTION:

Cat Bucyrus 2810 Drum Miner Operator’s & Maintenance Manual BI000234 – PDF DOWNLOAD

OPERATING PROCEDURE:
1. Make sure that everyone is clear of the machine and that all valves, breakers and switches are
in the neutral or off position.
2. Insure that proper voltage is being supplied o the machine.
3. Insure that water is being supplied to machine.
4. Turn on main circuit breaker (CBl).
5. urn on AUX circuit breaker (CBR).
6. Turn on area lightse
7. Select mode of operation (Manual or radio).
a. Select and turn on control valve for directional water spray.
9. Turn on headlights.
10. Start pump motor.
11. Raise or lower conveyor and cutter boom for adequate clearance and visibility.
12. Put gathering head in float position. For maximum cleanup efficiency, the gathering head
should rest against the mine floor and be free to float.
13. Tram machine to the face until cutterhead just touches face.
14. Position the rear conveyor over the shuttle car by raising and swinging to desired position.
15. Raise the cutter boom to the desired cutting height

IMAGES PREVIEW OF THE MANUAL:

Questions? Email us: [email protected]

PLEASE NOTE:

• This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
• This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
• Require some other service manual or have any queries: please WRITE to us at [email protected]

S.V