Challenger EU Tillage 2550 Five-Section Chisel Plough Operator’s Manual 9971457CHA

Description

Challenger EU Tillage 2550 Five-Section Chisel Plough Operator’s Manual 9971457CHA – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Challenger EU Tillage 2550 Five-Section Chisel Plough Operator’s Manual 9971457CHA – PDF DOWNLOAD

A word to the operator :

It is your responsibility to read and understand the safety section in this manual and the manual for all attachments before operating this machine. Remember you are the key to safety. Good safety practices not only protect you, but also the people around you. Study the content in this manual and make the content a working part of your safety program.

• Keep in mind that this safety section is written only for this type of machine. Practice all other usual and customary safe working precautions, and above all remember – safety is your responsibility. You can prevent serious injury or death. This safety section is intended to point out some of the basic safety situations that may be encountered during the normal operation and maintenance of your machine.
• This section also suggests possible ways of dealing with these situations. This section is not a replacement for other safety practices featured in other sections of this manual. Personal injury or death may result if these precautions are not followed. Learn how to operate the machine and how to use the controls properly.
• Do not let anyone operate the machine without instruction and training. For your personal safety and the personal safety of others, follow all safety precautions and instructions found in the manuals and on safety signs affixed to the machine and all attachments. Use only approved attachments and equipment.

This manual:

• This manual covers general safety practices for this machine. The operator manual must always be kept with the machine. Right-hand and left-hand, as used in this manual, are determined by facing the direction the machine will travel when in use.
• The photos, illustrations, and data used in this manual were current at the time of printing, but due to possible in-line production changes, your machine can vary slightly in detail. The manufacturer reserves the right to redesign and change the machine as necessary without notification.

TABLE OF CONTENTS:

Challenger EU Tillage 2550 Five-Section Chisel Plough Operator’s Manual 9971457CHA – PDF DOWNLOAD

1 Safety 7
1 1 lntroduction 9
1 1 1 Safety alert symbol 9
1 1 2 Safety messages 9
1 1 3 lnformational messages 9
1 1 4 Safety signs 9
1 1 5 А word to the operator 1 О
1 1 6 This manual 1 1
1 2 Operation 12
1 2 1 Ргераге for operation 1 2
1 2 2 General information 1 2
1 2 3 Personal protective equipment 1 3
1 2 4 Seat instructions 1 3
1 2 5 Shield and guards 1 4
1 2 6 Exhaust warning 1 4
1 2 7 Flying debris 1 5
1 2 8 Agricultural chemicals 1 5
1 3 Travel on puЫic roads 16
1 4 Maintenance 18
1 4 1 General maintenance information 1 8
1 4 2 Fire prevention and first aid 19
1 4 3 High pressure leaks 20
1 4 4 Tire safety 2 1
1 4 5 Replacement parts 2 1
1 5 Transport locks 22
1 6 Marker lamps 23
1 7 Safety sign location 24
2 lntroduction 31
2 1 lntroduction 33
2 1 1 Units of measurement 33
2 1 2 Replacement parts 33
2 1 3 lntended use 33
2 1 4 Ргорег disposal of waste 33
2 2 Machine identification 35
2 2 1 Serial number plate location 35
2 2 2 Serial number description 35
2 3 Chisel plough 37
2 3 1 Floating hitch 37
2 4 Major components 38
2 5 Operator manual storage 39
3 Operation 41
3 1 Connecting the machine to the tractor 43
3 2 Disconnecting the machine from the tractor 45
3 3 Bleeding air from the hydraulic lift system 46
3 4 Bleeding air from the hydraulic fold system 47
3 5 Preparing the machine for transport 48
3 6 Preparing the machine for field operation 49
Five-Section Chisel Plough
9977457СНА
ТаЬ!е of contents
3 7 Beginning field operation 50
3 7 1 ltems to check after first operation 50
3 8 Leveling the machine 51
3 8 1 Leveling а machine with the floating hitch front to геаг 51
3 8 2 Leveling the wings to the center frame 51
3 9 Adjusting the gauge wheels 53
3 9 1 Adjusting the gauge wheels – hydraulic 53
3 10 Operating depth 54
3 1 0 1 Single point depth control 54
3 11 Spring shanks 55
4 Maintenance 57
4 1 Lubrication points 59
4 1 1 Lubrication and maintenance chart 59
4 1 2 Lubrication fitting locations 60
4 2 Servicing the wheel bearings 61
4 3 Servicing the tandem pivot bearings 62
4 4 Storage 63
4 4 1 Preparing the machine for storage 63
4 4 2 Preventing corrosion of extended hydraulic cylinders 64
4 4 3 Removing the machine from storage 64
5 TrouЬleshooting 65
5 1 TrouЬleshooting 67
6 Specifications 69
6 1 Specifications 71
6 2 Transport dimensions 72
6 3 Minimum tow vehicle weight 73
6 4 Maximum transport speed 74
6 5 Lubrication specifications 75
6 6 Tire air pressure 76
7 AssemЫy 77
7 1 Preparing for assemЫy 79
7 1 1 Service parts 7 9
7 2 AssemЫing the center frame 80
7 2 1 lnstalling the center lift 8 1
7 2 2 lnstalling the center lift hubs and wheels 8 2
7 2 3 lnstalling the center frame mast tubes 8 3
7 2 4 lnstalling the fold anchors 8 4
7 2 5 lnstalling the center frame wing rests 8 5
7 3 AssemЫing the tongue 86
7 3 1 lnstalling the tongue 8 7
7 3 2 lnstalling the utility pole 8 8
7 4 lnstalling the center frame shank extension 89
7 5 lnstalling the center frame shanks 90
7 5 1 lnstalling the 650 lb shanks 90
7 5 2 lnstalling the 1 000 lb shanks 91
7 6 lnstalling the slow moving vehicle (SMV) emЬlem 92
7 7 lnstalling the inner wings 93
7 7 1 Mounting the wing frame hinges 93
7 7 2 lnstalling the inner wing frames 93
Five-Section Chisel Plough
9971457СНА
ТаЬ!е of contents
7 7 3 lnstalling the inner wing frame shank extensions 9 4
7 7 4 lnstalling the front fold bracket 9 6
7 7 5 lnstalling the rear fold bracket 9 7
7 7 6 lnstalling the inner wing frame wing rests 9 8
7 8 lnstalling the inner wing frame shanks 99
7 8 1 lnstalling the 6 50 lb shanks 9 9
7 8 2 lnstalling the 10 0 0 lb shanks 10 0
7 9 lnstalling the inner wing lifts 101
7 9 1 lnstalling the inner wing lift hubs and wheels 10 2
7 1 О lnstalling the inner wing frame mast tubes 103
7 11 lnstalling the outer wings 104
7 11 1 lnstalling the 14 9 to 16 2 m (49 to 53 ft) outer wing frames 10 4
7 11 2 lnstalling the 14 9 to 16 2 m (49 to 53 ft) outer wing frame shank extensions 10 5
7 11 3 lnstalling the 16 8 to 18 m (55 to 59 ft) outer wing frames 10 6
7 11 4 lnstalling the 16 8 to 18 m (55 to 59 ft) outer wing frame shank extensions 10 7
7 11 5 AssemЫing the outer wing latch components 10 8
7 12 lnstalling the outer wing frame shanks 109
7 12 1 lnstalling the 6 50 lb shanks 10 9
7 12 2 lnstalling the 1О ОО lb shanks 11О
7 13 lnstalling the outer wing lifts 111
7 13 1 lnstalling the outer wing lift hubs and wheels 112
7 14 lnstalling the outer wing frame mast tubes 113
7 15 lnstalling the stroke control assemЫy 114
7 15 1 Mounting the stroke control vavle 114
7 15 2 Mounting the front of the stroke control 115
7 15 3 Mounting the rear of the stroke control 116
7 16 lnstalling the hydraulic gauge wheels 117
7 16 1 lnstalling the gauge wheel mount- hydraulic 117
7 16 2 lnstalling the gauge wheel linkage – hydraulic 118
7 16 3 AssemЫing the center frame gauge wheel axle – hydraulic 119
7 16 4 lnstalling the center frame gauge wheel axle- hydraulic 120
7 16 5 AssemЫing the wing frame gauge wheel axle- hydraulic 121
7 16 6 lnstalling the wing frame gauge wheel axle – hydraulic 122
7 16 7 lnstalling the gauge wheel hubs and wheels- hydraulic 123
7 16 8 lnstalling the center frame gauge wheel lift tubes- hydraulic 124
7 16 9 lnstalling the wing frame gauge wheel lift tubes- hydraulic 125
7 17 lnstalling the marker lamps 126
7 17 1 lnstalling the marker lamp harness 127
7 18 lnstalling the rear tow hitch 128
7 19 lnstalling the hydraulics 130
7 19 1 lnstalling the center lift cylinders 130
7 19 2 lnstalling the wing lift cylinders 131
7 19 3 lnstalling the 14 9 to 16 2 m (49 to 53 ft) lift hydraulics 132
7 19 4 lnstalling the 16 8 to 18 m (55 to 59 ft) lift hydraulics 134
7 19 5 lnstalling the center fold cylinders 136
7 19 6 lnstalling the outer fold cylinders 137
7 19 7 lnstalling the fold hydraulics 138
7 20 Shank locations – 30 5 cm (12 in) spacing 140
7 20 1 14 9 m (49 ft) shank locations – 30 5 cm (12 in) spacing 140
7 20 2 15 5 m (51 ft) shank locations – 30 5 cm (12 in) spacing 142
7 20 3 16 2 m (53 ft) shank locations – 30 5 cm (12 in) spacing 144
7 20 4 16 8 m (55 ft) shank locations – 30 5 cm (12 in) spacing 146
7 20 5 17 4 m (57 ft) shank locations – 30 5 cm (12 in) spacing 148
7 20 6 18 0 m (59 ft) shank locations – 30 5 cm (12 in) spacing 150
7 21 Shank locations – 38 1 cm (15 in) spacing 152
Five-Section Chisel Plough
9977457СНА
ТаЬ!е of contents
7 2 1 1 1 4 9 m (4 9 ft) shank locations – 3 8 1 cm (1 5 in) spacing 1 52
7 2 1 2 1 5 5 m (51 ft) shank locations – 3 8 1 cm (1 5 in) spacing 1 54
7 2 1 3 16 2 m (53 ft) shank locations – 3 8 1 cm (1 5 in) spacing 1 56
7 2 1 4 16 8 m (55 ft) shank locations – 3 8 1 cm (1 5 in) spacing 1 58
7 2 1 5 1 7 4 m (57 ft) shank locations – 3 8 1 cm (1 5 in) spacing 160
7 2 1 6 1 8 О m (59 ft) shank locations – 3 8 1 cm (1 5 in) spacing 162
7 22 Checklists 164
7 2 2 1 Pre-delivery checklist 164
7 2 2 2 Delivery checklist 164
8 lndex 165

CHALLENGER EU TILLAGE 2550 FIVE-SECTION CHISEL PLOUGH OPERATOR’S MANUAL 9971457CHA:

PLEASE NOTE:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

S.V