CLAAS CORTO 310 S / 310 N Typ 653 CORTO 270 S / 270 NC / 270 N Typ 649 Assembly instructions and operator’s manual- PDF DOWNLOAD

Description

CLAAS CORTO 310 S / 310 N Typ 653 CORTO 270 S / 270 NC / 270 N Typ 649 Assembly instructions and operator’s manual- PDF DOWNLOAD

DESCRIPTION:

CLAAS CORTO 310 S / 310 N Typ 653 CORTO 270 S / 270 NC / 270 N Typ 649 Assembly instructions and operator’s manual- PDF DOWNLOAD

INTRODUCTION

This operator’s manual provides information concerning the use, setting and operation of the CLAAS drum mower. Follow the advice on correct maintenance and servicing in order to ensure maximum performance and a long service life of your machine. Also ensure that the assembly of your machine and regular inspections are carried out by a specialist workshop. Failure to carry out maintenance work, or incorrect operation will result in poor machine efficiency and loss of valuable time. Make use of the experience and latest knowledge applied in this machine by operating and caring for it properly. Your mower unit will always produce good results

Safety rules

Before putting the machine into operation, read the operator’s manual and and follow the safety precautions!

DESIGNATED USE

• • The CLAAS drum mower is exclusively built for normal use for agricultural work (correct use). The mower unit is suitable and intended for cutting crops growing from the ground in wild or seeded fields.
  • Use in any other way is considered as contrary to the intended use. The manufacturer is not liable for damage resulting from such uses; the user is solely responsible for such risks. Designated use also includes observing the service, maintenance and repair conditions as prescribed by the manufacturer.
  • The CLAAS mower unit may only be used, serviced and repaired by persons who are familiar with and trained in the dangers involved. Observe the applicable accident prevention regulations and other generally acknowledged regulations regarding safety and occupational health, as well as the regulations and standards relevant to motor vehicles and traffic.
  • Modification of the machine without proper authority precludes any manufacturer’s liability for damage resulting from any such modifications

TABLE OF CONTENTS:

CLAAS CORTO 310 S / 310 N Typ 653 CORTO 270 S / 270 NC / 270 N Typ 649 Assembly instructions and operator’s manual- PDF DOWNLOAD

1 Introduction
Introduction 11
Validity 11
2 Contents
3 Preface
Of special importance 31
Type plate 31
4 Safety rules
Designated use 41
Identification of warning and danger signs 41
General safety and accident prevention instructions 41
Attached machines 43
Machines as trailers 43
PTO Operation 43
Hydraulic system 43
Tyres 44
Maintenance 44
Sound pressure level 44
Safety decals with pictorials 45
5 Specifications
CORTO 310 S 51
CORTO 310 N 51
CORTO 270 S 51
CORTO 270 NC 51
CORTO 270 N 51
Calculation of axle loads, minimum
ballasting and total weight 52
Calculation of minimum ballasting at the front 53
Calculation of minimum ballasting at the rear 53
Calculation of the real front axle load 53
Calculation of the real total weight 53
Calculation of the real rear axle load 54
Tyre load carrying capacity 54
Noise level 55
6 Assembly
Assembly CORTO 310 S / 310 N / 270 S / 270 N with swath
discs 61
Assembly CORTO 270 S with conditioner 63
Assembly CORTO 270 NC 65
Installation of cutting blades 66
Installation of pull rope 67
Hydraulic system 67
Initial assembly of machine 68
7 Prior to operation
Check and observe the following
before putting into operation 71
Attachment to the tractor 72
Hitch pins 72
Drive shaft 74
Adapting the PTO shaft length 74
Fitting the PTO drive shaft 74
Attaching the universal drive shaft 75
Wide-angle-synchronism-joint 75
Hydraulics 76
Prop stand 77
Detaching the machine 77
Prior to transport 78
Driving on public roads 79
8 Operation
Operation 81
Working position 81
Safety frame 82
Transport position 83
Cutting height adjustment 84
Overload safeguard 85
Flotation springs 85
Conditioner 86
Swath discs 87
Mowing 87
Recommendation for environmental protection 88
Optional equipment 810
Sliding disc extension for high cut 810
Cranked blades 810
Re-inforced blades 810
Conversion kit for 1000 rpm PTO speed 811
Conversion kit swath discs with cover 812
Hydraulic adapter kit for tractors 812
Universal joint yoke kit 812
High cut adapter kit 812
9 Maintenance
Important Maintenance Instructions 91
Hydraulic system 91
Pretensioned or prestressed energy aumulators 91
Bolts 91
Lubrication 91
Guards 91
Drive Mechanism 92
Tensioning the drive belts 92
Gearbox and gear casing 93
Conditioner gearbox 94
Cutting blades 94
Replacement of cutting blades 95
Knife holders 96
Cutting height adjustment 97
Swath discs 97
Conditioner 98
Installation and removal of the conditioner tines 98
Hydraulics 99
Hydraulic hose connections 99
Hydraulic cylinder with vacuum valve 99
Universal drive shaft 910
Screw connections 910
Connecting elements 911
End of season storage 911
10 Lubrication Chart
Safety rules 101
Lubricants 101
Lubrication 101

IMAGES PREVIEW OF THE MANUAL:

CLAAS CORTO 310 S / 310 N TYP 653 CORTO 270 S / 270 NC / 270 N TYP 649 ASSEMBLY INSTRUCTIONS AND OPERATOR’S MANUAL- PDF DOWNLOAD:

PLEASE NOTE:

• This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
• Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.

s.m