CLAAS DISCO 9400 C DUO Conversion to front/rear combination Conversion to towed rear combination Conversion instructions Manual

Description

CLAAS DISCO 9400 C DUO Conversion to front/rear combination Conversion to towed rear combination Conversion instructions Manual

DESCRIPTION:

CLAAS DISCO 9400 C DUO Conversion to front/rear combination Conversion to towed rear combination Conversion instructions Manual

Safety rules
Fitting and conversion work

• The work described in this manual may be carried out only by a qualified specialist workshop with trained skilled staff
• Prior to fitting or converting:

► Read and follow safety instructions in all Operator’s Manuals: Operator’s Manual of the machine or product intended for fitting or installation Operator’s Manual of the product to be fitted or installed

► Observe the safety decals applied to the machine and the product.

► Observe general safety instructions, accident prevention rules and environmental protection regulations.

► Stop and secure the machine and the product.

► Carry out work beneath the raised machine, beneath raised implements or raised components only if these units are securely supported.

► Lower down the machine, front attachment and hydraulically actuated components prior to any work on the hydraulic system. Depressurize the system.

► Relieve the pressure of pre-stressed energy accumulators (springs, accumulators, hydraulic cylinders) and of components pressurized by energy accumulators. After fitting or converting:

► Clean any soiled safety decals. Replace any unidentifiable or missing safety decals

. ► Refit any removed protective guards and other components and set them to their protective position before putting into operation again.

► Check if all bolts are tightly seated.

► Perform a function test. Introduction Safety rules 2793-001 00
TABLE OF CONTENTS:

CLAAS DISCO 9400 C DUO Conversion to front/rear combination Conversion to towed rear combination Conversion instructions Manual

DISCO 9400 C DUO 1
Table of contents 3
Introduction 4
Notes on the manual 4
Validity of the manual 4
Information about these conversion instructions 4
Symbols and notes 5
Identifying warnings 6
Hazard signs 6
Signal word 6
Safety rules 7
Fitting and conversion work 7
Front/rear-mounted combination 8
Check list 8
Checklist for conversion to front/rear combination 8
Work preparation 9
Lowering the load relief 9
Unhitching the front mower from the DISCO 9400 C DUO 9
Unhitching DISCO 9400 C DUO from the tractor10
Removing the covers11
Front mower unit12
Removing the light bar12
Preparing the front mower13
General13
Removing the universal drive shaft13
Converting the swath setting system13
Removing the hydraulic hose lines14
Fitting the hydraulic hose lines14
Installing the universal drive shaft15
Fitting the front mower load relief system15
Rear mowers16
Adapting the overlap16
Relocating mower units16
Adapter20
Removing cylinders20
Removing the upper link21
Removing the adapter22
Hitch24
Removing the universal drive shaft24
Removing the ball splines24
Removing the guards24
Fitting the ball splines25
Hydraulic system26
Turning the pressure gauges26
Removing the connection cables for the front mower27
Converting the connection cables for the tractor29
Fastening the connection cables32
Fitting the panels34
Converting the magnetic holder34
Universal drive shaft36
Installing the universal drive shaft36
Lighting38
Fitting the light bar38
Hitching the machine40
Hitching the front mower to the tractor40
Hitching DISCO 9400 C DUO to the tractor40
Pushed rear-mounted combination41
Check list41
Conversion to towed rear combination41
Work preparation42
Lowering the load relief42
Unhitching the front mower from the tractor42
Unhitching DISCO 9400 C DUO from the tractor42
Removing the covers43
Lighting44
Removing the light bar44
Universal drive shaft47
Removing the universal drive shaft47
Hydraulic system49
Turning the pressure gauges49
Preparing the connection cables for the front mower50
Converting the connection cables for the tractor51
Fitting the connection cables for the front mower54
Converting the magnetic holder55
Hitch57
Removing the ball splines57
Fitting the ball splines58
Installing the universal drive shaft58
Adapter59
Fitting the adapter59
Attaching the guards61
Installing the upper link62
Fitting the cylinders64
Connecting the cylinders65
Fitting the panels65
Rear mowers66
Relocating mower units66
Front mower unit69
Unhooking the elastic rope69
Fitting the light bar69
Preparing the front mower71
General71
Removing the front mower load relief71
Removing the universal drive shaft71
Converting the swath setting system72
Removing the hydraulic hose lines72
Fitting the hydraulic hose lines72
Installing the universal drive shaft73
Hitching the machine74
Hitching DISCO 9400 C DUO to the tractor74
Hitching the front mower to the DISCO 9400 C DUO74
Index76
A76
B76
C76
D76
F76
G77
H77
I77
L77
M77
N77
P77
R77
S78
U78
V78
W78

IMAGES PREVIEW OF THE MANUAL:

CLAAS DISCO 9400 C DUO CONVERSION TO FRONT/REAR COMBINATION CONVERSION TO TOWED REAR COMBINATION CONVERSION INSTRUCTIONS MANUAL:

PLEASE NOTE:

• This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
• Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.

s.m