Claas Domintor 58/ 58 S Domintor 48 Spezial Operator’s Manual – PDF DOWNLOAD

Description

Claas Domintor 58/ 58 S Domintor 48 Spezial Operator’s Manual – PDF DOWNLOAD

DESCRIPTION:

Claas Domintor 58/ 58 S Domintor 48 Spezial Operator’s Manual – PDF DOWNLOAD

INTRODUCTION

• This book is intended to give the machine driver information on setting, using and servicing the CLAAS range of DOMINATOR 58 S / SPEZIAL and DOMINATOR 48 S / SPEZIAL combines. Texts and pictures apply, in general, to all combine models covered by this book, and the information given applies equally, except where reference is made to a particular model in captions to the pictures or in the main text.
• Operation and maintenance of important ancillary equipment is also covered by this manual. Please read the instructions which apply to the appropriate ancillary equipment on your combine. Provided you follow the advice on the care and servicing of your machine you will be rewarded with reliable and long service from your Combine Harvester.
• We recommend that you allow your authorized CLAAS Dealer to carry out the regular maintenance. Omissions of parts of the maintenance schedule or incorrect operation lead to a drop in performance and cost valuable time. By correct servicing and operation you can make full use of our sound experience and of the latest technical knowledge in
• Combine Harvesting with which your combine has been designed and thereby insure reliability of your Combine Harvester. This Operator’s Manual can be ordered from your CLAAS Dealer as well as the manuals listed below:

General information
ROAD TRAFFIC REGULATIONS

• In addition to the driving licence, the operator must always carry the copy of the vehicle type approval registration issued by the Kraftfahrt-Bundesamt (the Federal Motor Vehicle Executive). A warning triangle and, on machines over 4 t permissible total weight, at least one wheel chock must always be carried on the combine.
• When driving on public roads with the combine, comply with all the requirements stated under letter C in the copy of the vehicle type approval registration (§ 18 Section 5 StVZO) issued by the Kraftfahrt-Bundesamt (the Federal Motor Vehicle Executive). On machines with exceptional width (width over the tyres), a vehicle type approval registration for individual
• vehicles (single expert opinion) and a special approval in accordance with § 70, Section 1, clauses 1 and 2 of the StVZO must be carried instead of the machine’s General Operating Permit. Furthermore, all the requirements stated in the vehicle type approval registration for individual vehicles and in the special approval must be observed. The issue of a special approval
• differs from country to country. The excess width must be marked in accordance with the regulations for the marking of road vehicles with excess width (two marker boards at the front and back, protective bar, two amber flashing warning beacons). If any part(s) of the combine is/are subsequently modified whose condition is/are prescribed or the operation of
• which (after being modified) could represent a hazard to other road users, then the vehicle type approval registration shall no longer be valid and application must be made for a new vehicle type approval registration. In this case the machine must be presented to the motor vehicle safety inspection authority responsible (TÜV) in order to obtain an expert opinion
• certificate (§ 19 section 2 StVZO). If you are in any doubt as to whether this situation applies in your case, please contact us as manufacturers. If a transport vehicle for front end attachments is towed behind the combine then the cable for the lighting system must be connected and the good condition of the lighting system assured. If the combine is equipped with a
• maize picker head or a folding cutterbar, the regulations and requirements of the machine’s General Operating Permit must be observed, in particular the requirements concerning ballast weights and tyres
  TABLE OF CONTENTS:

Claas Domintor 58/ 58 S Domintor 48 Spezial Operator’s Manual – PDF DOWNLOAD

CONTENTS
1 Introduction
Introduction 111
2 Contents
Contents 211
3 General information
Road Traffic Regulations 311
Important 321
Identification Plate / Serial Number 331
Identification plate 332
Combine serial number 332
Engine serial number 332
Engine serial number 333
Engine serial number 333
Cutterbar serial number 333
Straw chopper serial number 333
Cab serial number 334
4 Safety rules
Safety Rules 411
Safety lock 414
Fire extinguisher 414
Battery isolating switch 414
Wheel chock (Not for all countries) 415
Straw guide apron 415
Safety Decals With Pictorials 421
5 Specifications
CLAAS DOMINATOR 58 / 48 Spezial 511
Cutterbar 511
Threshing Equipment 511
Straw Walkers 511
Cleaning 512
Returns 512
Grain tank 512
Engines 512
Battery 512
Fuel tank 512
Ground drive 512
Ground speeds 512
Traction wheel drive 512
Steering 512
Tyre sizes and pressures 513
Brakes 513
Torque settings of wheel bolts 513
Weights 513
Combine dimensions 514
Wheel tread 514
Width over tyres 514
Wheel base 514
Ground clearance 514
Turning diameter conforming to DIN 70020 514
Transport position / working position 515
Safety features 516
Sectional View Of Combine 521
Description and function of the combine 522
Cutterbar 522
Threshing parts 523
Straw walkers 523
Cleaning 523
Disawning 523
Basic rules for combining 524
6 Prior to operation
Before Initial Operation 611
Driver’s Platform 621
Cab 622
Cab with ventilating system 623
Cab with ventilating system and air conditioner 623
Cab with ventilating system and heating 625
Problem, cause and / or remedy –
Compressor-type air conditioner 626
Steering column 627
Ignition switch (S) 627
Vehicle information unit 628
Adjusting the steering column 628
Central terminal compartment 628
Hydraulic control unit (lift hydraulic system) 629
Instrument panel 629
Control levers 6210
Swinging the grain tank unloading tube 6210
Cutterbar height indicator 6211
Driver’s seat (standard version) 6211
Driver’s seat (optional equipment) 6212
Platform ladder 6212
Front ladder 6212
Rear ladder 6212
Functions monitor 6213
Work lights 6213
Cab 6214
Sun roof 6214
Driving the Combine 631
Starting the engine 631
Transmission of power 632
Gear selection and clutch 632
Stopping the combine 633
Driving behaviour 633
Steering 633
Brakes 633
Foot brake 633
Handbrake 634
Stopping the engine 634
Towing 635
7 Operation – cutterbar
Attaching the Cutterbar 711
Levelling the cutterbar 713
Cutterbar clutch 714
Adjustment of cutterbar cylinders 715
Adjusting the cutterbar floatation springs 715
Contents
212 BA DOMINATOR 58 / 58 S / 48 Spezial – 298 3670
Contents
Adjustments at the Cutterbar 721
Crop dividers 721
Outer deflector 721
Inner deflector 721
Special crop divider (extra equipment) 722
Grain lifters 722
Knife 722
Removing the knife 723
Installing the knife 723
Adjusting the knife keeps 723
Knife timing 724
Spare knife 724
Cutterbar skids 724
Reel 724
Adjusting the tension of the reel drive chain 725
Adjusting the spring-Ioaded cylinder 725
Mechanical fore and aft reel adjustment 725
Hydraulic fore and aft reel adjustment 726
Variable speed reel drive 727
Main table auger 728
Replacing knife sections in the field 729
Cutterbar trailer 729
8 Operation – basic machine
Feeder Housing 811
Cutterbar reverse drive 811
Treshing Mechanism 821
Stone trap 821
Engaging the threshing mechanism 821
Disengaging the threshing mechanism 822
Concave adjustment 822
Threshing drum 823
Cleaning the threshing parts 823
Drum variable speed pulleys 824
Slow speed threshing drum drive kit (Chain drive) 824
Unslugging the threshing drum 825
Disawning 825
Filler rasp bars 826
Impeller 826
Deflector curtain 827
Straw Walkers and Cleaning 831
Straw walkers 831
Intensive separation system 831
Straw walker risers 832
Cleaning the straw walkers 833
Audible warning signal 833
Preparation floor 834
Pulling out the preparation floor 834
Sieve pan 835
Cleaning fan 835
Fan shutters for combining grass seed and
other special crops 836
Adjusting the frogmouth sieves 837
Lower sieve 837
Changing the lower sieve 837
Dynamic sidehill levelling (3-D cleaning system) 838
Returns 839
Combine performance monitor 839
Adjusting the sensor sensitivity (Sieve pan sensor) 8311
Adjusting the sensor sensitivity (Straw walker sensor) 8311
Grain Delivery 841
Augers and auger troughs 841
Elevators 841
Grain tank 842
Unloading the tank 842
Hydraulic swing of grain tank unloading tube 843
Swinging the grain tank unloading tube in or out 843
Engaging the grain tank unloading augers 843
Disengaging the grain tank unloading augers 843
Safety feature 844
Safety feature adjustment 844
Clean-out door on grain tank discharge tube 845
Shear bolt – grain tank unloading system 845
Straw Chopper 851
Before using the straw chopper, check 851
Putting the straw chopper into operation 852
Adjusting the length of cut 853
Putting the straw chopper out of operation and changing over to
windrowing straw 854
Changing the sieve while straw chopper is fitted 855
Moving the chopper back to front position 856
Deactivating the speed-loss monitor 856
Hitching the cutterbar trailer 856
Sieve and Threshing Chart 861
Sieve chart 861
Threshing chart 862
Problem, Cause and / or Remedy – Basic Machine 871
Threshing equipment 873
Straw walkers 874
Cleaning 875
Dynamic sidehill levelling 3-D cleaning unit 875
Returns 876
Elevators 876
Grain tank 876
9 Maintenance – basic machine, cutterbar
Important Maintenance Instructions 911
Maintenance Schedules and Lubricants Charts 921
Maintenance Schedules 921
Lubricants Chart 923
Hydraulic System / Chassis 931
Lift hydraulic system 931
Tensioning the pump drive V-belt 931
Checking the oil level 931
Changing the hydraulic oil 931
Cleaning the screen filter 932
Replacing the paper filter cartridge 932
Bleeding the reel cylinders 933
Adjusting the ground drive clutch 933
Setting the bypass valve 934
Footbrakes / brake fluid 934
Transmissions 941
Change-speed transmission 941
Final drives 941
Adjusting the gear shift control 941
Drive Belts and Chains 951
Changing the variable speed belts 951
Threshing drum variable speed belt 951
298 3670 – BA DOMINATOR 58 / 58 S / 48 Spezial 213
Contents
Ground drive belt 952
Fan variable speed belt 953
Adjusting the ground drive belt 955
Adjusting the threshing mechanism drive 957
Adjusting the cutterbar drive 958
Adjusting the V-belt clutch of unloading auger drive 959
Diagram of sieve pan drive belt 9510
Straw walker drive 9511
Tensioning the auger drive belt 9511
Intensive separation system drive 9511
Elevator Chains 961
Adjusting the tension of elevator chains 961
Clean grain elevator 961
Returns elevator 961
Feeder Housing 971
Greasing the feeder housing coupling forks 971
Tensioning the feed rake feeder chains 971
Cab / Compressor-type Air
Conditioner 981
Cab 981
Cleaning the filters 981
Compressor-type air conditioner 981
Tensioning the compressor drive V-belt 981
Compressor-type air conditioner system
preventive maintenance during prolonged shut-down 982
Cleaning the evaporator 982
Cleaning the condenser 983
Checking the refrigerant level 983
Replacing the filter receiver drier 984
Required quantity of refrigerant R 134 a 984
Maintenance work before the harvest 985
Fire extinguisher 985
Speeds 991
Speed of straw walker crankshaft 991
Functions monitor 991
Straw Chopper 9101
Changing the free-swinging knive 9101
Adjusting the spring-loaded cylinder at the
intermediate drive 9102
Winter Storage Instructions for Combines 9111
10 Maintenance – Engine
Important Maintenance Instructions 1011
Maintenance Schedule and Lubricants Chart 1021
Maintenance chart 1021
Lubricants chart 1022
Maintenance – Engine 1031
Engine overview 1031
Fuel system 1032
Fuel tank 1032
Fuel pre-filter 1033
Water separator / fuel pre-filter
(extra equipment – replaces fuel pre-filter) 1033
Fuel filter 1034
Bleeding the fuel system 1035
Checking the engine oil level 1035
Engine oil change 1035
Draining oil 1036
Oil filter 1036
Filling in engine oil 1037
Tensioning the V-belts 1037
Tensioning the alternator / fan drive belt 1037
Cooling System 1041
Water drain plugs on the engine block 1041
Water drain plugs on the engine block 1042
Radiator 1042
Coolant 1043
Filling the cooling system with coolant 1043
Overpressure 1043
Coolant temperature 1044
Warning signal 1044
Radiator chaff screen 1044
Cleaning rotor 1044
Cleaning the radiator 1045
Dry-type Air Cleaner 1051
Warning device 1051
Cleaning the air cleaner intake screen 1051
Cleaning the air cleaner 1051
Cleaning the dry-type air cleaner 1052
Removing the main filter cartridge 1052
Installing the main filter cartridge 1053
Safety cartridge 1053
Electrical System 1061
Battery 1061
Alternator 1062
Engine Problems, Cause and / or Remedy 1071
Engine Winter Storage 1081
Engine preservation 1081
Operating the engine again 1081
11 Lubrication chart
12 Index
Index 1211
IMAGES PREVIEW OF THE MANUAL:

CLAAS DOMINTOR 58/ 58 S DOMINTOR 48 SPEZIAL OPERATOR’S MANUAL – PDF DOWNLOAD:

PLEASE NOTE:

• This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
• The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
• Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer

S.M