Claas Lexion 460 – 410, Lexion 480 470 Operator’s Manual – PDF DOWNLOAD

Description

Claas Lexion 460 – 410, Lexion 480 470 Operator’s Manual – PDF DOWNLOAD

DESCRIPTION:

Claas Lexion 460 – 410, Lexion 480 470 Operator’s Manual – PDF DOWNLOAD

SAFETY RULES
Important instruction!
1. Prior to road travel, ensure the machine is completely
lowered.
2. When turning, never turn in the direction of
downhill, but always turn uphill.
3. When operating on steep slopes, always operate
sideways or uphill.
4. Be especially careful when working on slopes!
The speed must always match the ground conditions.
The machine must always be operated in the
horizontal position (level).
5. Should a fault occur with the automatic levelling,
then stop the machine immediately.
Switch off the automatics. Level the machine
manually.
6. When working on slopes, the brake pedals must
be locked together.
Never operate the brakes individually.
7. Be especially careful when working in the dark!
8. Take care for high voltage power lines!
9. Be especially careful when using the ladder on the
downhill side. When stepping up or down from the
machine, if it is necessary correct the angle
manually.

TABLE OF CONTENTS:

Claas Lexion 460 – 410, Lexion 480 470 Operator’s Manual – PDF DOWNLOAD

1 Introduction
Introduction 1 1 1
2 Contents
Contents 2 1 1
4 Safety Rules
Safety Rules 4 1 1
Safety decals with pictorials 4 2 1
5 Specifications
CLAAS LEXION 470 Montana 5 1 1
CLAAS LEXION 430 Montana 5 2 1
6 Prior to operation
Slope compensation 6 1 1
Operator’s platform overview 6 1 2
Control console 6 1 3
Slope compensation control box 6 1 4
Monitor 6 1 5
Machine operation 6 1 6
Axle (wheel angle) 6 1 6
Cutterbar 6 1 6
Axle (wheel angle) and cutterbar 6 1 7
Menu 6 1 9
Cutterbar adjustment key pad (yellow) 6 1 9
Axle adjustment key pad (green) 6 1 9
Calibration 6 1 10
Calibrating the inclinometer 6 1 10
Calibrating the wheel rams 6 1 11
Calibrating the cutting angle 6 1 11
Calibrating the cross levelling 6 1 11
Calibrating the trunking (feeder housing) 6 1 12
Setup 6 1 13
System info 6 1 14
Inclinoinfo 6 1 14
Access ladder 6 1 15
Front ladder 6 1 15
Checking the control lights 6 1 16
Driving the combine 6 1 16
Engine speed rotary switch 6 1 16
Gear selection 6 1 17
Manoeuvring 6 1 17
Hydrostatic ground drive 6 1 18
Starting the engine 6 1 19
Stopping 6 1 20
Driving behaviour 6 1 20
Steering 6 1 20
Brakes 6 1 21
Foot brake 6 1 21
Parking brake 6 1 22
Releasing the parking brakes mechanically 6 1 22
Turn gears into «0» (neutral position) 6 1 23
Differential lock 6 1 23
Engaging the differential lock 6 1 23
Disengaging the differential lock 6 1 23
Malfunction, possible cause or remedy 6 1 24
10 Maintenance – basic machine
Maintenance schedules and lubricants charts 10 1 1
Maintenance schedule 10 1 1
Lubricants chart 10 1 2
Gearboxes 10 2 1
Differential and axle support 10 2 2
Checking the oil level 10 2 2
Oil change 10 2 2
Wheel pivots 10 2 3
Checking the oil level 10 2 3
Oil change 10 2 3
Planetary gearbox 10 2 3
Checking the oil level 10 2 3
Oil change 10 2 3
2-speed gearbox 10 2 4
Checking the oil level 10 2 4
Oil change 10 2 4
Rotary frame guide roller adjustment 10 2 4
Adjusting the sensor for the
cutting angle adjustment 10 2 4
Adjusting the sensor for the wheel pivots 10 2 5
11 Maintenance – engine
Important maintenance instructions 11 1 1
Important maintenance instructions
and safety rules 11 1 1
Maintenance schedules and lubricants charts 11 2 1
Maintenance schedule 11 2 1
Lubricants chart 11 2 2
12 Lubrication chart
Lubricants and lubrication instructions 12 1 1

CLAAS LEXION 460 – 410, LEXION 480 470 OPERATOR’S MANUAL – PDF DOWNLOAD:

IMAGES PREVIEW OF THE MANUAL:

PLEASE NOTE:

• This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
• Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.

S.V