Claas LEXION 580 – 510 Soybean cutterbar 4.50 M – 9.00 M Operator’s Manual – PDF DOWNLOAD

Description

Claas LEXION 580 – 510 Soybean cutterbar 4.50 M – 9.00 M Operator’s Manual – PDF DOWNLOAD

DESCRIPTION:

Claas LEXION 580 – 510 Soybean cutterbar 4.50 M – 9.00 M Operator’s Manual – PDF DOWNLOAD

INTRODUCTION

This manual is valid for the CLAAS Soybean Cutterbar for Lexion 580 – 510. It is intended primarily for the machine operator and provides information concerning the use, adjustment and operation of the cutterbar. For commissioning the Soybean Cutterbar, see the combine harvester operating instructions The advice on care and servicing should be followed in order to obtain maximum performance and long service from the Soybean Cutterbar. In addition, regular inspections of the machine should be carried out by your CLAAS specialist workshop. Neglect in maintenance or service, and incorrect use will result in poor machine efficiency and loss of time. This manual is only valid in conjunction with the combine harvester’s operating instructions

General information
SPECIAL CARE

• In order to prevent accidents, the instructions contained in this manual should be carefully read and observed by all persons involved with the operation, maintenance, and inspection of this machine.
• Especially the section “Safety rules” should be read and observed. The use of spare parts, accessories and ancillary equipment, which are not originally manufactured by CLAAS, can change the specified design of this CLAAS machine or detract from its functional performance, with a possible adverse effect on the active and/or passive operational safety of the
• machine and its occupational safety standards (accident prevention). CLAAS is in no way liable for any damage or personal injury caused through the use of parts other than original CLAAS parts, accessories, and ancillary equipment. Technical specifications, dimensions, and weights are non-binding.CLAAS reserves the right to make changes subsequently as
• technical developments continue. Liability for errors or omissions not accepted. “Front”, “rear”, “right” and “left” always refer to the direction of travel.

TABLE OF CONTENTS:

Claas LEXION 580 – 510 Soybean cutterbar 4.50 M – 9.00 M Operator’s Manual – PDF DOWNLOAD

TABLE OF CONTENTS
1 Introduction
Introduction 111
2 Table of contents
Table of contents 211
3 General information
Special care 311
Identification plate 321
4 Safety rules
Safety rules 411
Cylinder safety lock 421
Feeder housing 421
Reel 421
Safety decals with pictorials 431
5 Prior to operation
Carry out before initial operation 511
Removing the transport fixtures 511
Adjusting the cutterbar flotation springs 511
Fitting the right-hand cutterbar cylinder 511
Fitting a third cutterbar cylinder 511
Coupling section for machines with CLAAS Contour
(without transverse control) 521
Fitting the coupling section 521
6 Operation – Cutterbar
Mounting the cutterbar 611
Adjusting the hydraulic cylinder for
transverse control of the cutterbar 611
Connecting the universal drive shaft 612
Fitting the quick-release coupling 613
Unmounting the cutterbar 613
Adjusting the cutterbar 621
Cutterbar skids 621
Reel 621
Reel tines 622
Horizontal reel adjustment 623
Knife 623
Standard knife system 624
Standard knife system settings 625
SG3/S and SG3 knife systems 626
SG3/S and SG3 knife system adjustment 626
Intake auger 627
Adjusting the clearance to the bottom plate 627
Adjusting the feed finger control 627
Changing the inclination of the cutter bar 628
Crop dividers 6210
Adjusting the divider points 6210
Basic crop divider setting 6211
Replacing the divider points 6212
Fitting the insert for long divider points 6213
Conversion from soybeans to grain 631
Removing the soybean sensor 631
Fitting the sensor bands 632
Changing over the sensors and adjustment 632
Adjusting the sensor actuating levers to the end stops 633
Arresting the cutter bar 634
Conversion from grain to soybean 641
Changing over the sensors and adjustment 641
Adjusting the sensor actuating levers to the end stops 642
Fitting the soybean sensor 643
Unlocking the outer runner of the control arm 643
Remove stop bolts for cutter beam 644
7 Maintenance
Maintenance and lubricant table 711
Maintenance schedule 711
Lubricants chart 712
Knife drive gearbox 721
Checking the oil level / oil change 721
Adjusting the drive support 722
Adjusting the spring cylinder 722
Drive belts / drive chains 731
Removing the knife drive belt (40) 731
Fitting the knife drive belt (40) 732
Tensioning the intake auger drive chain (41) 732
Tensioning the reel drive 732
Inductive sensor for reel drive 733
8 Lubrication chart
Lubricants and notes 811
9 Index
Index 911
IMAGES PREVIEW OF THE MANUAL:

CLAAS LEXION 580 – 510 SOYBEAN CUTTERBAR 4.50 M – 9.00 M OPERATOR’S MANUAL – PDF DOWNLOAD:

PLEASE NOTE:

• This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
• The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
• Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer

S.M