Claas TUCANO 450 Type 840 Operator’s Manual – PDF DOWNLOAD

Description

Claas TUCANO 450 Type 840 Operator’s Manual – PDF DOWNLOAD

DESCRIPTION:

Claas TUCANO 450 Type 840 Operator’s Manual – PDF DOWNLOAD

1 Introduction
1.1 General Information
1.1.1 Validity of manual

This manual is only valid for use in conjunction with the corresponding operator’s manual for the associated machine. This manual only contains the information that differs from the user’s manual. The present Manual applies to the following machine / front attachment

3 Safety
3.1 General Information
3.1.1 Intended use

• The CLAAS combine harvester is designed exclusively for professional use in line with the recognised regulations of agricultural practices in agricultural harvesting of grain. The combine harvester is a self-propelled harvesting machine with a fitted front attachment (machine), which is approved by the manufacturer, and is suitable and intended for harvesting
• grain in fields during travel. Grain here refers to cultivated cereal and legume crops such as wheat, rye, barley, oats, rice, rape seed, maize, durra, soya beans and sunflowers. The combine harvester takes the grain from the front attachment and conveys it via a conveying unit to the threshing and separating units. There, the grains are separated from straw and chaff.
• The straw and chaff are deposited on the field using the distribution units behind the combine harvester. The grain is stored temporarily in the combine harvester’s grain tank and then loaded on a transport vehicle by a conveying unit. When the combine harvester is driven on public roads, a front attachment approved by the manufacturer can be fitted on the front,
• depending on the applicable regulations, and driven with the combine harvester, or a trailer approved by the manufacturer that is loaded with the front attachment can be coupled to the trailer hitch and towed. The machine may only be used, maintained and serviced by persons who are familiar with the machine and briefed on the hazards that may arise as a result
• of the machine’s functions. Compliance with the conditions of operation, maintenance and servicing as specified in the operator’s manual and by the manufacturer also constitute essential elements for the intended use. The relevant accident prevention regulations, all other generally recognised regulations on safety and occupational medicine and the road traffic
• regulations must be observed by users and owners at all times. Any use other than this is considered “unintended”, and the manufacturer is not liable for any resulting damage. All liability in this case is borne by the user. For specific details, you may request information on intended use in exceptional situations from CLAAS.

TABLE OF CONTENTS:

Claas TUCANO 450 Type 840 Operator’s Manual – PDF DOWNLOAD

Contents
1 Introduction
11 General Information 8
111 Validity of manual 8
2 Sectional view of machine
21 Attachment parts / machine body 9
211 Access to the workplace and maintenance areas 9
3 Safety
31 General Information 11
311 Intended use 11
312 Reasonable foreseeable misuse 12
313 Decommissioning and disposal 13
32 Safety decals 14
321 Separation 14
322 Crop receptacle / straw receptacle 15
4 Specifications
41 TUCANO 450 – Type 840 17
411 General information 17
412 Engine 17
413 Chassis 18
414 Tyre pressures 19
415 Chassis track width 20
416 Brake 22
417 Steering 22
418 Electric system / Electronics 22
419 Cab / Operator’s platform 22
4110 Intake 23
4111 Threshing mechanism 24
4112 Separation 24
4113 Cleaning unit 25
4114 Grain delivery 25
4115 Grain delivery dimensions 26
4116 Attachment parts / machine body dimensions 27
4117 Attachment parts / machine body weights 29
5 Prior to initial operation
51 General Information 30
511 General warnings Prior to initial operation 30
52 Various components / Machine body 31
521 Opening / closing the rotor drive side panel 31
522 Using rear ladder 32
10 Fieldwork settings
101 General Information 33
1011 General warnings Fieldwork 33
6 00 0290 378 2 – ERG BA TUCANO 450 – 12/09
70155
102 Feeder unit 34
1021 Adjusting the speed of front attachment drive belt (R1) 34
1022 Adjusting the cutting angle of the
V-type feed rake conveyor (optional
equipment) to its basic adjustment 35
12 Fieldwork
121 General Information 37
1211 General warnings Fieldwork 37
122 Feeder unit 38
1221 Adjusting the cutting angle of the V-type feed rake conveyor
(optional equipment) 38
123 Separation 40
1231 Adjusting the rotor speed 40
1232 Observe the straw blockage warning downstream of the separation stage 41
1233 Adjusting the separation performance monitor display 41
124 Crop receptacle / straw receptacle 42
1241 Putting the straw chopper into operation
(swinging the standard spreader to chopping position) 42
1242 Putting the straw chopper out of operation
(swinging the standard spreader to swathing position) 43
125 Sieve charts / threshing charts 45
1251 Threshing chart (TUCANO 450) 45
14 Maintenance
141 General Information 50
1411 General warnings Maintenance 50
142 Maintenance schedule 51
1421 Service intervals 51
143 Lubricants chart 52
1431 Lubricants 52
144 Engine 53
1441 Fill up the machine’s fuel tank 53
1442 Cleaning the additional fuel tank filling screen (accessory) 54
1443 Changing the fuel filter (additional fuel tank, accessory) 54
1444 Changing the fuel filter (CATERPILLAR C-9) 56
1445 Bleeding the fuel system (CATERPILLAR C-9) 57
1446 Checking the diesel engine oil level (CATERPILLAR C-9) 57
1447 Changing the diesel engine oil / oil filter (CATERPILLAR C-9) 58
145 Brake 61
1451 Adjusting the foot brake 61
1452 Checking the wheel chocks / brake shoes 61
1453 Changing the wheel chocks / brake shoes 61
146 Drive belts / drive chains 63
1461 General warnings 63
1462 Drive diagram, left side of TUCANO 450 64
1463 Drive diagram, right side of TUCANO 450 65
1464 Adjusting belt (R20) 66
1465 Adjusting belt (R22) 67
1466 Adjusting belt (R23) 68
00 0290 378 2 – ERG BA TUCANO 450 – 12/09 7
70155
1467 Removing belt (R24) 69
1468 Installing belt (R24) 70
1469 Adjusting belt (R24) 71
14610Adjusting belt (R25) 72
14611Removing belt (R43) 73
14612Installing belt (R43) 74
14613Adjusting belt (R49) 76
14614Removing belt (R50) 77
14615Installing belt (R50) 78
14616Adjusting belt (R50) 78
147 Separation 79
1471 Checking the rotor gearbox oil level 79
1472 Draining the rotor gearbox oil 79
1473 Topping up rotor gearbox oil 80
1474 Cleaning the separation throughput monitor sensor 81
1475 Cleaning the rotor 82
15 Lubrication chart
151 Lubrication points 83
1511 General warnings Lubrication chart 83
1512 Lubricants 83
1513 Greasing cycles 84
1514 Lubrication points – 10 h on the left 85
1515 Lubrication points – 10 h on the right 86
1516 Lubrication points – 50 h on the left 87
1517 Lubrication points – 100 h on the left 88
1518 Lubrication points – 500 h on the left 89
1519 Lubrication points – 500 h on the right 90
IMAGES PREVIEW OF THE MANUAL:

CLAAS TUCANO 450 TYPE 840 OPERATOR’S MANUAL – PDF DOWNLOAD:

PLEASE NOTE:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

S.M