CLAAS VARIANT 260 – VARIANT 260 RC VARIANT 280 – VARIANT 280 RC Bonded belt Fitting Instruction Manual_DE_EN_FR

Description

CLAAS VARIANT 260 – VARIANT 260 RC VARIANT 280 – VARIANT 280 RC Bonded belt Fitting Instruction Manual_DE_EN_FR

DESCRIPTION:

CLAAS VARIANT 260 – VARIANT 260 RC VARIANT 280 – VARIANT 280 RC Bonded belt Fitting Instruction Manual_DE_EN_FR

Introduction

1.1 General Information

This manual describes the work to do to fit Variant 260/ 260RC and Variant 280/280RC balers with spliced belts. Replacing damaged belts with spliced belts can be partial (from 1 to 4 belts) or total (a complete set of 5 belts). The Safety regulations in the operator’s manual for the baler must be observed.  

Safety regulations
2.1 Important
2.1.1 General Information

• To prevent accidents, these instructions must be read by everyone who uses the machine and who deals with maintenance, servicing or inspection. In particular, read the “Safety Rules” in this manual with utmost care and observe the accident prevention regulations applicable in the country of use. Before starting work, establish if all tools and equipment are at
• hand. Compare the machine/attachment type at hand with the list in section “Scope of parts” and the delivered spare parts set . The specification of the parts, e.g. for bolts, can be found in the list headed “Scope of parts”. In this list, every mounting part has a position number (pos.-no.). In the installation instructions, the current parts are marked with letters and the new
• parts with numbers (position numbers) for easier orientation. Texts and pictures have been kept neutral whenever possible.Text references point out the differences between the individual types. Technical data, dimensions and weights are given as an indication only. Following the policy of CLAAS to improve their products as technical developments continue,
• CLAAS reserve the right to make alterations. Responsibility for errors or omissions not accepted. Front, rear, right hand and left hand always refer to the machine as seen in the direction of forward travel

TABLE OF CONTENTS:

CLAAS VARIANT 260 – VARIANT 260 RC VARIANT 280 – VARIANT 280 RC Bonded belt Fitting Instruction Manual_DE_EN_FR

1 Introduction
11 General Information 32
12 Machines to be equipped 32
2 Safety regulations
21 Important 33
211 General Information 33
212 Intended use 33
22 Safety regulations 34
221 Marking of warning and danger notes 34
222 General safety regulations and instructions for the avoidance of accidents 35
223 Leaving the machine 35
23 Safety regulations relating to bonding products 35
231 Composition of bonding products 35
232 Identifying the risks 35
233 Measures to be taken in case of accidental spillage 36
234 Handling and storage 36
235 Monitoring exposure and individual protection 37
236 Environmental information 38
237 Other information 38
24 Safety instructions specific to RCE cleaning product 38
241 Composition of RCE cleaning product 38
242 Danger symbols 38
243 Identifying the risks 38
244 Fire prevention measures 39
245 Measures to be taken in case of accidental spillage 39
246 Monitoring exposure and individual protection 40
247 Information on poisoning 40
248 Environmental information 41
249 Disposing of the RCE cleaning product 41
3 Scope of parts
31 Scope of parts – for bonding belts 42
311 VARIANT 260 – VARIANT 260 RC: 0843 7320 42
312 VARIANT 280 – VARIANT 280 RC: 0843 7300 43
4 Fitting a new belt
41 Equipment required 44
411 Safety, cleaning and bonding materials 44
000 293 946 0 – ABA KH LEX / LEX MONTANA 560-510 – 12/05 5
1446
412 Equipment for support 45
42 Preparation of the baler 45
421 Securing baler 45
422 Slackening belts 45
423 Removing damaged belt 46
43 Assembling the new belt 47
431 Positioning the bonded belts 47
432 Inserting a new belt 49
433 Fixing the belt 50
434 Cleaning surfaces to be bonded 51
435 Pre-bonding 52
436 Bonding 54
437 Drying period 55
44 Putting baler into service again 55
441 Changing a belt 55
442 Changing 2 or more belts 55
IMAGES PREVIEW OF THE MANUAL:

CLAAS VARIANT 260 – VARIANT 260 RC VARIANT 280 – VARIANT 280 RC BONDED BELT FITTING INSTRUCTION MANUAL_DE_EN_FR:

PLEASE NOTE:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

S.M