Clark Forklift EC50-70 English O-9K-1 Operator’s Manual

Description

Clark Forklift EC50-70 English O-9K-1 Operator’s Manual

CLARK FORKLIFT EC50-70 ENGLISH O-9K-1 OPERATOR’S MANUAL:

Image Preview:

Description:

Clark Forklift EC50-70 English O-9K-1 Operator’s Manual

• SAFETY INSTRUCTIONS FOR MAINTAINING INDUSTRIAL TRUCKS r:rnm mmmm Powered industrial trucks may becane hazardous if adequate maintenance is neglected. Therefore, adequate maintenance facilities, personnel and procedures should be provided. Maintenance and inspection of all powered industrial trucks should be performed in conformance with the reconvnendation in this manual and the following practices.
• 1. A scheduled preventive maintenance, lubrication, and inspection system should be followed. 2. Only qualified and authorized personnel should be permitted to maintain, repair, adjust, and inspect industrial trucks. 3. Before leaving The Truck: A. Stop truck. B. Fully lower the load engaging means. c. Place direct ion al controls in neutral. D. Apply the parking brake.
• E. Stop the engine or F. Lock the control or G. Block the wheels if 4. Before Working On Truck: turn off ignition truck is power. circuit. on a ramp, or being worked on. A. Raise wheels free of floor or disconnect power source. B. Use chocks or other positive truck positioning devices. C. Block load engaging means, innermast(s), or chassis before working under them.
• Before working on engine fuel system of gasoline powered trucks with gravity feed fuel systems, be sure fuel shutoff valve is closed. Before working on engine fuel system of LP gas powered trucks, close LP gas cylinder valve and run engine until fuel in system is depleted and engine stops running. Operation to check performance of the truck or attachments should be conducted in an authorized, safe clearance area.
• 5. Before Starting To Operate The Truck; A. Be in operating posit ion. B. Depress clutch (or brake pedal on autanatic transmission and electric trucks). C. Place directional controls in neutral. D. Start engine or turn on power. E. Before operating truck, check functioning of I ift and tilt systems, directional and speed controls, steering, warning devices, brakes, and any attachment. (If used) F. Release parking brake.

Table Of Contents:

Clark Forklift EC50-70 English O-9K-1 Operator’s Manual

F orwerd, reverse, 1A contactors, inspect and adjust.
Lubrication Charts
500 Hour Lubrication & Preventive Maintenance Illustration
Hydraulic sump tank, drain and refill.
Hydraulic sump tank filter, change.
Steering gear, check and adjust.
Steering adjustments.
1000 Hour Lubrication & Preventive Maintenance Illustration
Typical drive motor assembly.
Typical drive motor assembly (disassembled view) .
Drive and pump motor, inspect; brush spring tension, check.
brushes, inspect.
Typical pump drive motor (disassembled view).
Steering wheel bearings, clean, repack and adjust.
Axle ends, clean and repack.
Brake system, i 11 ustrat ion.
Brake system, bleed.
Service wheel brake assembly.
Seat safety brake (parking brake), check and adjust.
Seat I inkage disconnect p’in.
Axle adapter, drain and refill.
Typical control valve illustration.
System pressure checks.
Lift carriage rollers, check and adjust.
Lift carriage and upright roller, specs.
Upright rollers, check and adjust.
TROUBLE SHOOTING GUIDE
Drive Axle
S<eering Axle
Br’akes
Brakes
Hydraulic System
Hydraulic System
Sol id State Control, test and adjust.
Hydraulic Circuit Diagram
Si de Sh if te r
Pi.np, Drive, Traction Motor
Pmp, Drive, Traction Motor Specs*
Ree I s,·,
,·, Located at rear of manua I .

Please Note:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

sk