CLARK FORKLIFT OH-437 NP and NS 300 Lot 3205 and Up OVERHAUL MANUAL

Description

CLARK FORKLIFT OH 437 NP and NS 300 Lot 3205 and Up OVERHAUL MANUAL – PDF DOWNLOAD

Contact us: [email protected]

Image Preview:

Description:

CLARK FORKLIFT OH 437 NP and NS 300 Lot 3205 and Up OVERHAUL MANUAL – PDF DOWNLOAD

• Powered industrial trucks may become hazardous if adequate maintenance is neglected. Therefore, adequate maintenance facilities, personnel and procedures should be provided. Maintenance and inspection of all powered industrial trucks should be performed in conformance with the reconvnendation in this manual and the following practices.
• 1. A scheduled preventive maintenance, lubrication, and inspection system should be followed. 2. Only qua! ified and authorized personnel should be permitted to maintain, repair, adjust, and inspect industrial trucks. 3- Before Leaving The Truck: A. Stop truck. B. Fully lower the load engaging means. C. Place directional controls in neutral. D. Apply the parking brake.
• E. Stop the engine or turn off power. F. Lock the control or ignition circuit. G. Block the wheels if truck is on a ramp, or being worked on. 4. Before Working On Truck: A. Raise wheels free of floor or disconnect power source. B. Use chocks or other positive truck positioning devices. C. Block load engaging means, innermast(s), or chassis before working under them.
• Before working on engine fuel system of gasoline powered trucks with gravity feed fuel systems, be sure fuel shutoff valve is closed. Before working on engine fuel system of LP gas powered trucks, close LP gas cylinder valve and run engine until fuel in system is depleted and engine stops running. Operation to check performance of the truck or attaclYnents should be conducted in an authorized, safe clearance area.
• s. Before Starting To Operate The Truck; A. Be in operating position. B. Depress clutch (or brake pedal on automatic transmission and electric trucks). C. Place directional controls in neutral. D. Start engine or turn on power. E. Before operating truck, check functioning of lift and tilt systems, directional and speed controls, steering, warning devices, brakes, and any attachment. (If used) F. Release parking brake.

Table Of Contents:

CLARK FORKLIFT OH 437 NP and NS 300 Lot 3205 and Up OVERHAUL MANUAL – PDF DOWNLOAD

Accelerating Control (HMS)
Drive Motor Overhaul • • •
Commutator Check Chart • •
Steer Pump Motor Overhaul
General Motor Maintenance
TABLE OF CONTENTS
Pump Motor Overhaul • • • •
Forward-Reverse Contactors • •
lA and Pump Contactors •
G.E. Electrical Contactors
Square D Electrical Panel ••
NS300 – Lots 3205-3496
NP300 – Lots 3205-3491
G,E. SCR Panel Overhaul • • • •
NS300 – Lot 3497 & above
NP300 – Lot 3492 & above
Drive Axle Overhaul •
Drive Motor Brake Overhaul
NP300 – Lo·ts 3205-3207
NS300 – Lots 3210-3211
Drive Motor Brake Overhaul •
NP300 – Lot 3490 & above
NS300 – Lot 3495 & above
Power Steering Pump Overhaul •
Steer Torque Generator Overhaul
Lift Pump Overhaul .
Reach & Tilt Pump Overhaul . •
Hydraulic Valve Overhaul . •
Cessna Reach & Tilt Valve •
Dual Tilt Cylinder Overhaul •
Reach Cylinder Overhaul • •
NP300 – Lots 3205-3492
Reach Cylinder Overhaul
NP300 – Lot 3995 & above
Upright Lift Cylinder Overhaul .
Lubrication Specifications

Please Note:

• This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
• This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
• Require some other service manual or have any queries: please WRITE to us at [email protected]

sk