Isuzu (6UZ1 EURO5 Standard Specification) Engine 2011-2013MY FX/FY/GX Series Workshop Manual PDF
$28.95
Isuzu (6UZ1 EURO5 Standard Specification) Engine 2011-2013MY FX/FY/GX Series Workshop Manual – PDF DOWNLOADΒ
Description
Isuzu (6UZ1 EURO5 Standard Specification) Engine 2011-2013MY FX/FY/GX Series Workshop Manual – PDF DOWNLOADΒ
FILE DETAILS:
Isuzu (6UZ1 EURO5 Standard Specification) Engine 2011-2013MY FX/FY/GX Series Workshop Manual – PDF DOWNLOADΒ
Language : English
Pages : 299
Downloadable : Yes
File Type : PDF
IMAGES PREVIEW OF THE MANUAL:
TABLE OF CONTENTS:
Isuzu (6UZ1 EURO5 Standard Specification) Engine 2011-2013MY FX/FY/GX Series Workshop Manual – PDF DOWNLOADΒ
ΠΎ GENERAL INFORMATION ΠΠ General lnformation
1 ENGINE 1Π Enaine Control Svstem
18 Enaine Mechanical
1Π‘ Enaine CoolinQ
1D Engine Fuel
1Π Enaine Electrical
1G Enaine Exhaust
1Π EnQine Lubrication
11 Enaine Soeed Control Svstem
1J lnduction
1L Power Take-Off (Π Π’Π)
2 SUSPENSION 2Π Front Suspension
2Π‘ Rear Susoension
2D Wheel and Tire Svstem
3 DRIVELINE/AXLE ΠΠ Differential
ΠΠ‘1 Propeller Shaft
ΠΠ‘2 Front Axle
Π·ΡΠ· Rear Axle
4 BRAKES 4ΠΠ Brake Control Svstem (Full Air)
4Π3 Brake (Full Air)
4Π‘ Anti-Lock Brake (ABS)
4D Parkina Brake
4F Speed Retarder Svstem
4G Trailer Brake
5 TRANSMISSION/Π’RANSAXLE 5Π Transmission Control Svstem
5Π Automatic Transmission
5Π‘ Manual Transmission
5Π Clutch
6 STEERING 6Π Power Steering
7 HVAC ?Π Heatina and Ventilation
7Π Manual Air Conditioninq
?Π‘ Automatic Air Conditionina
8 RESTRAINTS 8Π Seat Belt
8Π Suoolemental Restraint Svstem (SRS)
8Π‘ SRS Control System
9 BODY, Π‘ΠΠ AND ACCESSORIES 9Π Liahtina Svstem
9Π Wioer/Washer Svstem
9Π‘ Entertainment
9D Wiring Svstem
9Π lnstrumentation/Driver lnfo.
9F Bodv Structure
9G Π‘Π°Π¬
9Π Seats
91 Security and Lock
9Π Exterior/lnterior Trim
9L Π‘Π°Π¬ Mounting
10 CONTROL SYSΠ’EMS 10Π Vehicle Control
11 FRAME AND FRAME ACCESSORIES 11Π Frame
DESCRIPTION:
Isuzu (6UZ1 EURO5 Standard Specification) Engine 2011-2013MY FX/FY/GX Series Workshop Manual – PDF DOWNLOADΒ
β’ When lifting ΠΎΠ³ supporting the engine, do not attach the jack to the oil pan. Use an engine pallet, wooden frame, etc., to support the engine with the engine foot ΠΎΠ³ flywheel housing.
β’ When the air intake/exhaust system has been removed, apply Π° seal to prevent foreign materials from entering the cylinder. Entry of foreign materials causes significant damage to the cylinder etc.
β’ ΠΠ΅ sure to remove the negative terminal (-) of the battery during maintenance. Take adequate precautions for safety, such as short circuits, when inspections require an energized state.
β’ Π’ΠΎ protect and lubricate the sliding parts, apply an adequate amount of engine oil to the sliding parts.
β’ When the valve related parts, pistons, piston ring connecting rod, bearing, injector, etc. have been removed, organize them in order for storage.
β’ When installing, use the same part and install it in the same position as when it was removed.
β’ Completely wipe off old liquid gasket from the locations where it is used. After cleaning to completely remove any oil, moisture and filth, apply the specified liquid gasket for reassemΠ«y.
β’ After applying the liquid gasket, assemΠ«e within 5 minutes. lf 5 minutes have passed, remove the old liquid gasket and apply liquid gasket again.
β’ When assemΠ«ing and installing, tighten at the specified torque value.
β’ Do not use any fallen ΠΎΠ³ strongly bumped sensors ΠΎΠ³ injection system parts. Otherwise they will cause failures.
S.V 06/01/2025Β Β
