Komatsu 150A 150FA Hydraulic Crane Shop Manual CEBM001400 PDF

Description

Komatsu 150A 150FA Hydraulic Crane Shop Manual CEBM001400 – PDF DOWNLOAD

FILE DETAILS:

Komatsu 150A 150FA Hydraulic Crane Shop Manual CEBM001400 – PDF DOWNLOAD 

Language : English
Pages : 756
Downloadable : Yes
File Type : PDF

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Komatsu 150A 150FA Hydraulic Crane Shop Manual CEBM001400 – PDF DOWNLOAD 

SERIAL NUMBERS
150A 10828 and UP 
150FA 10828 and UP 

GENERAL PRECAUTIONS :
Mistakes in operation are extremely dangerous. Read the OPERATION & MAINTENANCE MANUAL carefully BEFORE
operating the machine.
1. Before carrying out any greasing or repairs, read all the precautions given on the decals which are fixed to the machine.
2. When carrying out any operation, always wear safety shoes and helmet. Do not wear loose work clothes, or clothes with buttons missing.
• Always wear safety glasses when hitting parts with a hammer.
• Always wear safety glasses when grinding parts with a grinder, etc.
3. If welding repairs are needed, always have a trained, experienced welder carry out the work. When carrying out welding
work, always wear welding gloves, apron, glasses, cap and other clothes suited for welding work.
4. When carrying out any operation with two or more workers, always agree on the operating procedure before starting.
Always inform your fellow workers before starting any step of the operation. Before starting work, hang UNDER
REPAIR signs on the controls in the operator’s compartment.
5. Keep all tools in good condition and learn the correct way to use them.
6. Decide a place in the repair workshop to keep tools and removed parts. Always keep the tools and parts in their correct
places. Always keep the work area clean and make sure that there is no dirt or oil on the floor. Smoke only in the areas
provided for smoking. Never smoke while working.
PREPARATIONS FOR WORK 
1. Before adding oil or making repairs, park the machine on hard, level ground, and block the wheels or tracks to prevent the machine from moving.
2. Before starting work, lower blade, ripper, bucket or any other work equipment to the ground. If this is not
possible, insert the safety pin or use blocks to prevent the work equipment from falling. In addition, be sure to lock all the
control levers and hang warning signs on them.
3. When disassembling or assembling, support the machine with blocks, jacks or stands before starting work.
IMPORTANT SAFETY NOTICE:
Proper service and repair is extremely important for the safe operation of your machine. The service and repair techniques
recommended and described in this manual are both effective and safe methods of operation. Some of these operations
require the use of tools specially designed for the purpose.
To prevent injury to workers, the symbols and are used to mark safety precautions in this manual. The cautions
accompanying these symbols should always be followed carefully. If any dangerous situation arises or may possibly arise, first consider safety, and take the necessary actions to deal with the situation.
4. Remove all mud and oil from the steps or other places used to get on and off the machine. Always use the handrails,
ladders or steps when getting on or off the machine. Never jump on or off the machine. If it is impossible to use the
handrails, ladders or steps, use a stand to provide safe footing.
PRECAUTIONS DURING WORK 
1. When removing the oil filler cap, drain plug or
hydraulic pressure measuring plugs, loosen them slowly to prevent the oil from spurting out. Before
disconnecting or removing components of the oil, water or air circuits, first remove the pressure completely from the
circuit.
2. The water and oil in the circuits are hot when the engine is stopped, so be careful not to get burned. Wait for the oil and
water to cool before carrying out any work on the oil or water circuits.
3. Before starting work, remove the leads from the battery. ALWAYS remove the lead from the negative (-)
terminal first.

TABLE OF CONTENTS:

Komatsu 150A 150FA Hydraulic Crane Shop Manual CEBM001400 – PDF DOWNLOAD 

MAIN MENU 0
COVER 1
CONTENTS 2
00 INTRODUCTION 1
SAFETY 5
SAFETY NOTICE 5
IMPORTANT SAFETY NOTICE 5
GENERAL PRECAUTIONS 5
PREPARATIONS FOR WORK 5
PRECAUTIONS DURING WORK 6
ASBESTOS AND NON-ASBESTOS FIBERS 7
GENERAL 10
HOW TO READ THE SHOP MANUAL 11
VOLUMES 11
DISTRIBUTION AND UPDATING 11
FILING METHOD 11
REVISED EDITION MARK 11
REVISIONS 11
SYMBOLS 11
GENERAL MACHINE HOISTING INSTRUCTIONS 12
GENERAL MACHINE HOISTING 12
GENERAL MACHINE WIRE ROPES 12
COATING MATERIALS 13
STANDARD TIGHTENING TORQUE FOR METRIC 15
STANDARD TIGHTENING TORQUE OF BOLTS AND NUTS 15
TIGHTENING TORQUE OF HOSE NUTS 16
TIGHTENING TORQUE OF SPLIT FLANGE BOLTS 16
TIGHTENING TORQUE FOR FLARED NUTS 16
STANDARD TIGHTENING TORQUE FOR STANDARD ENGLISH 17
BOLT IDENTIFICATION CHART 17
TYPE 1, 5 AND 8 NON-PHOSPHATE COATED HARDWARE 17
TYPE 8 PHOSPHATE COATED HARDWARE 19
TORQUE VALUES FOR HOSE CLAMPS 19
TORQUE VALUES FOR SPLIT FLANGE CONNECTIONS 20
TORQUE VALUES FOR HYDRAULIC TUBES AND FITTINGS 20
ELECTRIC WIRE CODE 21
CLASSIFICATION BY THICKNESS 21
CLASSIFICATION BY COLOR AND CODE 21
CONVERSION TABLES 22
METHOD OF USING THE CONVERSION TABLE 22
01 GENERAL 29
GENERAL ASSEMBLY DRAWING 30
FUEL, COOLANT, AND LUBRICANTS 33
ACCORDING TO AMBIENT TEMPERATURE 33
PROPER SELECTION OF FUEL, COOLANT AND LUBRICANTS 33
ENGINE OIL SPECIFICATIONS 35
NORMAL OPERATION 35
ARCTIC OPERATION 35
TRANSMISSION, TORQUE CONVERTER AND OIL COOLER, AND HYDRAULIC SYSTEM OIL SPECIFICATIONS 36
REAR-DRIVE AXLE AND CIRCLE DRIVE BRAKE HOUSING OIL SPECIFICATIONS 36
DIESEL FUEL SPECIFICATIONS 36
COOLANT SPECIFICATIONS 37
GENERAL 37
WATER 37
ANTIFREEZE 37
SUPPLEMENTAL COOLANT ADDITIVES 39
MAINTENANCE OF SUPPLEMENTAL COOLANT ADDITIVES 39
COOLANT TESTING FOR CONDITIONER CONCENTRATION 39
REPLENISHING COOLANT CONDITIONER 39
SUPPLEMENTAL COOLANT ADDITIVE MAINTENANCE GUIDE 40
COOLING SYSTEM TEST KIT 42
10 STRUCTURE AND FUNCTION 43
WIRE ROPE 45
WIRE ROPE SPECIFICATIONS 45
MAINTENANCE RECOMMENDATIONS 45
TRANSMISSION – T20000 46
SPECIFICATIONS 47
OPERATION 50
POWERFLOWS 55
GEAR AND CLUTCH LAY-OUT 61
SECTIONAL VIEWS 62
CONVERTER HOUSING 62
TRANSMISSION CASE AND REAR COVER 64
TURBINE SHAFT 66
DRIVE PLATE 68
TORQUE CONVERTER 70
AUXLIARY PUMP DRIVE 72
PUMP DRIVE 74
FORWARD SHAFT 76
REVERSE AND 2ND SHAFT 78
REVERSE IDLER 80
LOW SPEED SHAFT 82
3RD SHAFT 84
IDLER SHAFT 86
OUTPUT SHAFT 88
HI & LOW RANGE SHIFT CONTROL 90
CHARGING PUMP & FILTER 92
TRANSMISSION CONTROL VALVE (MANUAL) 94
TRANSMISSION – HR18000 96
SPECIFICATIONS 98
HR18000 CONVERTER 100
HR18000 LONG DROP CONVERTER AND TRANSMISSION CASE 102
CONTROL VALVE 104
6 SPEED CLUTCH AND GEAR 106
REAR VIEW 109
POWER FLOW 110
LOW RANGE 110
HIGH RANGE 111
CLUTCH AND GEAR ARRANGEMENT 113
STEERING CONTROL VALVE 114
TYPICAL OIL FLOW 116
OPERATION 117
DESIGN AND FUNCTION 118
CONTROL VALVE 119
METERING SECTION 119
ROTOR OPERATION IN THE ROTOR SET 119
POWER STEERING OPERATION 120
MANUAL STEERING OPERATION 120
BRAKE VALVE – MASTER 121
MASTER CYLINDER SECTION 121
POWER ASSIST SECTION 121
BRAKE VALVE – EXPLODED VIEW 122
HYDRAULIC PUMP 124
DUAL TANDEM 124
EXPLODED VIEW 124
DUAL TANDEM PUMP CUTAWAY VIEW 125
SWING DRIVE MOTOR 126
EXPLODED VIEW 126
HOIST/WINCH MOTOR 127
EXPLODED VIEW 127
AUXILIARY HOIST MOTOR 128
EXPLODED VIEW 128
PARKING BRAKE 130
SERVICE BRAKE 131
AXLES 132
DIFFERENTIAL 132
PLANETARY AXLE WHEEL ENDS 136
SENSORS 139
BACKUP ALARM PRESSURE SWITCH 139
FUEL LEVEL SENDER 139
TORQUE CONVERTER OIL TEMPERATURE SENDER 140
ENGINE WATER TEMPERATURE SENDER 140
ENGINE OIL PRESSURE SENDER 140
NEUTRAL START SWITCH 141
BRAKE LIGHT OIL PRESSURE SWITCH 141
ENGINE HIGH WATER TEMPERATURE SWITCH (OPTION) 142
ENGINE LOW OIL PRESSURE SWITCH (OPTION) 142
REAR STEERING INDICATOR LIGHT SWITCH 143
TOWING THE CRANE 144
FRONT DRIVELINE 144
REAR DRIVELINE 144
20 TESTING, ADJUSTING AND TROUBLESHOOTING 145
TANDEM PUMP 147
WEAR CONSIDERATIONS IN CS & S PUMPS 147
TEST PROCEDURE FOR REBUILT PUMP 147
WINCH MOTOR 149
INSPECTION & REPLACEMENT 149
CLEANING 150
WINCH SPOOLING ADJUSTMENT 150
PROCEDURE FOR CORRECTING WINCH SPOOLING BY ROTATING AND SHIMMING 151
ROTATING PROCEDURE: 151
SHIMMING PROCEDURE: 152
HOIST AND SWING BRAKE CHECKS AND ADJUSTMENTS 153
HOIST BRAKE CHECKS AND ADJUSTMENTS 153
PRIMARY MANIFOLD 155
CLEANING AND INSPECTION 155
SECONDARY MANIFOLD 155
CLEANING AND INSPECTION 155
TESTING AND TROUBLESHOOTING 155
SWING DRIVE BEARING & GEAR ASSEMBLY WEAR TOLERANCE 156
PERMISSIBLE BEARING CLEARANCES 156
PROCEDURE FOR CLEARANCE MEASUREMENT 157
STEERING CONTROL VALVE 160
INSPECTION AND REPLACEMENT 161
FILLING AND AIR BLEEDING THE SYSTEM WHEN DRAINED OF OIL 163
HYDRAULIC FLUID 163
TIPS FOR MAINTAINING THE HYDROSTATIC STEERING SYSTEM 164
BRAKE VALVE 165
PRESSURE BLEEDING INSTRUCTIONS 165
BENCH BLEEDING INSTRUCTIONS 166
SPRING MOTORS 167
ADJUSTMENT 167
HEAD & HOOK BLOCK INSPECTION 168
HEAD 168
SHEAVES AND DRUM 168
HOOK BLOCK INSPECTION 168
DAILY/10 HOUR INSPECTION 168
ANNUAL/500 HOUR INSPECTION 169
WIRE ROPE 170
RESTING HOOK BLOCK 170
IMPORTANCE OF LUBRICATION 170
RECONNECTED LUBRICANTS FOR WIRE ROPE 171
METHODS OF LUBRICATION 171
LUBRICATION IN STORAGE 172
IDLE ROPES 172
INSPECTION OF WIRE ROPE, SHEAVES AND DRUM 173
BREAKING IN WIRE ROPE 174
RESETTABLE CIRCUIT BREAKERS 175
TROUBLESHOOTING 177
ALTERNATORS 179
PRELIMINARY CHECKS 179
LUBRICATION 182
CRANKING MOTOR 183
PRELIMINARY CHECKS 183
LUBRICATION 185
WIRE ROPE 186
HR18000 TRANSMISSION 187
PRESSURE CHECK POINTS 188
3 SPEED CLUTCH AND GEAR ARRANGEMENT 189
T20000 TRANSMISSION 190
STALL TEST 190
PRESSURE CHECKS 190
MECHANICAL AND ELECTRICAL CHECKS 191
HYDRAULIC CHECKS 191
GUIDE 192
CHECK POINTS 193
HYDRAULIC 196
HYDRAULIC PEDESTAL CRANE 196
INTRODUCTION TO THE HYDRAULIC SYSTEM 196
50 GPM CIRCUIT 198
50 GPM CONTROLS SLOW OR LACKING IN POWER WHEN 30 GPM AND FRONT STEERING CIRCUITS ARE NORMAL 198
30 GPM CIRCUIT 199
30 GPM CONTROLS SLOW OR LACKING IN POWER WHEN 50 GPM AND FRONT STEERING CIRCUITS ARE NORMAL 200
FRONT STEERING – SLOW, HARD OR STOPPED WHEN 30 AND 50 GPM SYSTEMS ARE FUNCTIONING PROPERLY 201
RAPID WARMUP OF HYDRAULIC SYSTEM 201
SWING DRIVE CIRCUIT 202
SWING DRIFTS AFTER CONTROL VALVE HAS BEEN RETURNED TO NEUTRAL 202
SWING RUNS AWAY WHILE SWINGING DOWN HILL WITH LOAD 203
SWING REFUSES TO ROTATE, WHEN OTHER 30 GPM CONTROLS FUNCTION NORMALLY 203
SWING ERRATIC AND JERKY IN OPERATION 204
BOOM LIFT CYLINDER 205
BOOM LIFT CYLINDER DRIFTS WITH HYDRAULIC CONTROL VALVE IN THE NEUTRAL POSITION 205
BOOM DROPS MOMENTARILY WHEN CONTROL IS MOVED FROM NEUTRAL TO RAISE 206
BOOM LIFT CYLINDER REFUSES TO LOWER 206
CROWD CYLINDER(S) 207
CROWD CYLINDER DRIFTS IN WITH OR WITHOUT LOAD 208
CROWD SECTION(S) CHATTERS OR REFUSES TO EXTEND UNDER HEAVY LOAD CONDITIONS 208
INSIDE CROWD CYLINDER CANNOT BE RETRACTED, CAUSED BY BROKEN OIL SUPPLY LINE ON A THREE SECTION POWER BOOM 209
INSIDE CROWD CYLINDER CANNOT BE RETRACTED, CAUSED BY BROKEN OIL SUPPLY LINE ON A FOUR SECTION POWER BOOM 210
REMOVAL OF THE INSIDE CROWD CYLINDER ON A THREE SECTION POWER BOOM 211
HOIST WINCH CIRCUIT 212
HOIST WINCH CIRCUIT OPERATION 214
HOIST WINCH DRIFTS WITH LOAD 214
HOIST WINCH CANNOT BE FEATHERED WHEN LOWERING A LOAD 217
HOIST WINCH WON’T LOWER OR HESITATES BEFORE LOWERING 217
HOIST WINCH LOWERS IN AN UNEVEN OR JERKY MANNER 218
HOIST WINCH WILL NOT LIFT LOAD 218
REAR STEERING 219
REAR STEERING CYLINDERS DRIFT 219
OUTRIGGERS 220
OUTRIGGER CYLINDER DRIFT 220
OUTRIGGERS CHATTER WHEN RAISING 221
SERVICE BRAKES 222
ADJUST BRAKE 222
WHEEL CYLINDER MAINTENANCE 222
WHEEL CYLINDER DIAGNOSTICS 223
BLEED HYDRAULIC SYSTEM 223
MAINTENANCE SCHEDULES 224
MINOR INSPECTION: HYDRAULIC BRAKES 224
MAJOR INSPECTION: HYDRAULIC BRAKES 225
PARKING BRAKE 226
ADJUST BRAKE 226
MAINTENANCE SCHEDULES 226
MINOR INSPECTION: MECHANICAL BRAKES 226
MAJOR INSPECTION: MECHANICAL BRAKES 226
PRE-DELIVERY PROCEDURE 227
PRE-UNLOADING CHECKS 229
EXAMPLE OF SERVICE REPORT ON DELIVERY 230
RECORD SERIAL NUMBERS 231
LUBRICATION 233
TORQUES 239
SPECIFIC BOLT TORQUES 240
ENGINE CHECKS 241
HYDRAULIC PRESSURE TEST 243
TRANSMISSION CHECKS 245
ADJUSTMENTS 247
ROTARY DRIVE SCREWS CLEARANCE 247
RETRACT REEL – SPRING MOTOR 247
BOOM ROLLERS 247
BOOM WEAR PLATES 247
SWING AND HOIST BRAKE ROD AND SPRING 248
CRANE OPERATION 249
TIRE INFLATION 249
REAR STEERING INDICATOR 249
TESTING 250
YARD TEST CRANE 250
ROAD TEST CRANE 250
ELECTRICAL SYSTEM CHECKS 250
30 DISASSEMBLY AND ASSEMBLY 251
METHOD OF USING MANUAL 257
PRECAUTIONS DURING OPERATION 258
PRECAUTIONS WHEN CARRYING OUT REMOVAL WORK 258
PRECAUTIONS WHEN CARRYING OUT INSTALLATION WORK 259
PRECAUTIONS WHEN COMPLETING THE OPERATIONS 260
OTHER PRECAUTIONS 260
SKETCHES OF SPECIAL TOOLS 262
REVERSE IDLER SHAFT NUT SOCKET (TG 1304 – 54) 262
HYDRAULIC MOTOR 263
STEEL SLEEVE 263
SEAL RETAINER TOOL 263
CHECK VALVE TOOL 264
SEAL RETAINER TOOL 264
DIFFERENTIAL CARRIER 265
REPAIR STAND 265
TRANSMISSION T20000 POWERSHIFT 6 SPEED 267
SERVICING MACHINE AFTER COMPONENTS OVERHAUL 267
TRANSMISSION TO ENGINE INSTALLATION PROCEDURE 268
CLEANING AND INSPECTION 269
CLEANING 269
INSPECTION 269
DISASSEMBLY 271
LOW (1ST) CLUTCH 285
REVERSE CLUTCH 293
2ND CLUTCH 301
3RD CLUTCH 305
FORWARD CLUTCH 310
CONVERTER HOUSING 318
IDLER SHAFT 329
OUTPUT SHAFT 333
ASSEMBLY 337
CONVERTER DRIVE COUPLING INSTALLATION DETAILS 360
HYDRAULIC ACTUATED AXLE DISCONNECT 362
SECTIONAL VIEWS AND PARTS IDENTICATION 362
OUTPUT SHAFT WITH AXLE DISCONNECT 365
AXLE DISCONNECT 370
TOWING OR PUSHING 378
TRANSMISSION 18000 SERIES 6 SPEED 379
DISASSEMBLY 379
FREEWHEEL DISASSEMBLY 383
TRANSMISSION CASE DISASSEMBLY 388
LOW CLUTCH 394
REVERSE AND 2nd CLUTCH 400
3RD CLUTCH 407
FORWARD CLUTCH 412
LOCK NUT TYPE IDLER SHAFT 419
TURBINE HUB ASSEMBLY WITH BACKING RING AND SPECIAL SELF LOCKING SCREWS 424
CONVERTER HOUSING 425
ASSEMBLY 428
FREEWHEEL ASSEMBLY 428
CONVERTER HOUSING 434
18000 SERIES TRANSMISSION CONVERTER DRIVE PLATE KIT 441
CLUTCH SHAFT OIL SEALING RING (PISTON RING) 442
INSTALLATION 442
TRANSMISSION TO ENGINE INSTALLATION PROCEDURE 444
SERVICING MACHINE AFTER TRANSMISSION OVERHAUL 445
TOWING OR PUSH STARTING 445
PEDESTAL, ROTEK BEARING & SWING DRIVE SYSTEM 446
REMOVAL 446
DRIVE MOTOR AND BRAKE 447
DISASSEMBLY 447
ASSEMBLY 453
INSTALLATION 462
SWING DRIVE MOTOR 464
REMOVAL 464
DISASSEMBLY 464
CLEANING 465
INSPECTION 466
ASSEMBLY 467
INSTALLATION 469
START-UP PROCEDURE 469
WINCH MOTOR 470
DISASSEMBLY 470
ASSEMBLY 474
BOOM WINCH 477
REMOVAL OF WINCH ASSEMBLY FROM CRANE 477
DISASSEMBLY 478
INSPECTION & CLEANING 483
ASSEMBLY 484
INSTALLING WINCH ASSEMBLY ON CRANE 489
JIB AND GANTRY 490
JIB EXTENSION PROCEDURE 490
JIB STOWAGE PROCEDURE 498
HEAD & HOOK BLOCK 499
DISASSEMBLY 499
ASSEMBLY 502
CARE OF WIRE ROPE 504
WIRE ROPE REPLACEMENT 504
HOOK & HEAD BLOCK REEVING 506
METHODS OF LUBRICATION 507
LUBRICATION IN STORAGE 507
SPRING MOTORS 508
UNLOADING RETRACT MECHANISM 508
DISASSEMBLY 510
SHAFT BEARINGS AND CABLE DRUM 514
ASSEMBLY 518
LOADING RETRACT MECHANISM 521
SETTING SPRING TENSION 521
LUBRICATION 522
BRAKE VALVE 523
MASTER CYLINDER SECTION 523
REMOVE AND SEPARATE INTO SECTIONS 523
DISASSEMBLY 524
ASSEMBLY 525
CONNECTING SECTIONS AND MOUNTING BRAKE VALVE ON VEHICLE 525
POWER ASSIST SECTION 527
REMOVE AND SEPARATE INTO SECTIONS 527
DISASSEMBLY 528
ASSEMBLY 529
CONNECTING SECTIONS AND MOUNTING BRAKE VALVE ON VEHICLE 530
STEERING CONTROL VALVE 532
SERVICING 533
DISASSEMBLY 533
ASSEMBLY 536
TANDEM PUMP 542
REMOVAL 542
DISASSEMBLY 544
ASSEMBLY 552
INSTALLATION 559
PRIMARY MANIFOLD & CONTROLS 560
REMOVAL 560
DISASSEMBLY 560
OPERATING CABLES 563
ASSEMBLY 566
OPERATING CABLES 566
INSTALLATION 571
PRIMARY MANIFOLD 572
REMOVAL 572
DISASSEMBLY 574
ASSEMBLY 576
INSTALLATION 578
SECOND MANIFOLD 580
REMOVAL 580
REMOVAL OF INDIVIDUAL VALVES 582
DISASSEMBLY 584
ASSEMBLY 586
INSTALLATION OF INDIVIDUAL VALVES 587
INSTALLATION 589
HYDRAULIC CYLINDERS 591
BOOM LIFT CYLINDER 591
DISASSEMBLY 591
ASSEMBLY 594
BOOM CROWD CYLINDER ROD SEAL 602
DUAL CROWD CYLINDER FOUR SECTION POWER BOOM 606
REMOVEAL 606
DISASSEMBLY 613
ASSEMBLY 617
INSTALLATION 625
STEERING CYLINDER 632
DISASSEMBLY 633
ASSEMBLY 633
OUTRIGGER CYLINDER 634
DISASSEMBLY 635
ASSEMBLY 635
LOWER CROWD CYLINDER 636
DISASSEMBLY 637
ASSEMBLY 637
SWING & HOIST BRAKE CYLINDER 638
DISASSEMBLY 639
ASSEMBLY 639
PARKING BRAKE 640
DISASSEMBLY 640
ASSEMBLY 641
SERVICE BRAKE 642
DISASSEMBLY 642
ASSEMBLY 643
WHEEL CYLINDER 645
DISASSEMBLY 645
ASSEMBLY 646
AXLES 647
DIFFERENTIAL 647
DISASSEMBLY 647
PREPARING PARTS FOR ASSEMBLY 659
ASSEMBLY 674
LUBRICANT 706
FASTENER TORQUE INFORMATION 708
ADJUSTMENTS AND SPECIFICATIONS 712
PLANETARY AXLE WHEEL ENDS 714
REMOVAL 714
PREPARE PARTS FOR ASSEMBLY 722
ASSEMBLY 722
90 OTHERS 733
HYDRAULIC 735
150A – SHEET 1 OF 2, PART 1 OF 2 735
150A – SHEET 1 0F 2, PART 2 OF 2 737
150A – SHEET 2 OF 2, PART 1 OF 2 739
150A – SHEET 2 OF 2, PART 2 OF 2 741
150FA – SHEET 1 OF 2, PART 1 OF 2 743
150FA – SHEET 1 OF 2, PART 2 OF 2 745
150FA – SHEET 2 OF 2, PART 1 OF 2 747
150FA – SHEET 2 OF 2, PART 2 OF 2 749
ELECTRICAL 751
150A/FA – SHEET 1 OF 1, PART 1 OF 2 751
150A/FA – SHEET 1 OF 1, PART 2 OF 2 753

S.V 14/12/24