kubota TRACTOR,MOWER,FRONT LOADER BX1870,BX2370,BX2670,RCK48-18BX,RCK54-23BX, RCK60B-23BX, RCK48P 18BX,RCK54P 23BX,LA203A, LA243A WORKSHOP MANUAL- PDF DOWNLOAD

Description

kubota TRACTOR,MOWER,FRONT LOADER BX1870,BX2370,BX2670,RCK48-18BX,RCK54-23BX, RCK60B-23BX, RCK48P 18BX,RCK54P 23BX,LA203A, LA243A WORKSHOP MANUAL- PDF DOWNLOAD

DESCRIPTION:

kubota TRACTOR,MOWER,FRONT LOADER BX1870,BX2370,BX2670,RCK48-18BX,RCK54-23BX, RCK60B-23BX, RCK48P 18BX,RCK54P 23BX,LA203A, LA243A WORKSHOP MANUAL- PDF DOWNLOAD

GENERAL PRECAUTIONS

• When you disassemble, carefully put the parts in a clean area
to make it easy to find the parts. You must install the screws,
bolts and nuts in their initial position to prevent the reassembly
errors.
• When it is necessary to use special tools, use KUBOTA special
tools. Refer to the drawings when you make special tools that
you do not use frequently.
Before you disassemble or repair machine, make sure that you
always disconnect the ground cable from the battery first.
• Remove oil and dirt from parts before you measure.
• Use only KUBOTA genuine parts for replacement to keep the
machine performance and to make sure of safety.
• You must replace the gaskets and O-rings when you assemble
again. Apply grease (1) to new O-rings or oil seals before you
assemble.
• When you assemble the external or internal snap rings, make
sure that the sharp edge (3) faces against the direction from
which force (2) is applied.
• When inserting spring pins, their splits must face the direction
from which a force is applied. See the figure left side.
• To prevent damage to the hydraulic system, use only specified
fluid or equivalent.
• Clean the parts before you measure them.
• Tighten the fittings to the specified torque. Too much torque can
cause damage to the hydraulic units or the fittings. Not sufficient
torque can cause oil leakage.
• When you use a new hose or pipe, tighten the nuts to the
specified torque. Then loosen (approx. by 45 °) and let them be
stable before you tighten to the specified torque (This is not
applied to the parts with seal tape).
• When you remove the two ends of a pipe, remove the lower end
first.
• Use two pliers in removal and installation. One to hold the stable
side, and the other to turn the side you remove to prevent twists.
• Make sure that the sleeves of flared connectors and tapers of
hoses are free of dust and scratches.
• After you tighten the fittings, clean the joint and apply the
maximum operation pressure 2 to 3 times to examine oil
leakage.

TABLE OF CONTENTS:

kubota TRACTOR,MOWER,FRONT LOADER BX1870,BX2370,BX2670,RCK48-18BX,RCK54-23BX, RCK60B-23BX, RCK48P 18BX,RCK54P 23BX,LA203A, LA243A WORKSHOP MANUAL- PDF DOWNLOAD

1. IDENTIFICATION …………………………………………………………………………………………………………. G-1
[1] TRACTOR IDENTIFICATION ……………………………………………………………………………………. G-1
(1) Serial Number and Hour Meter …………………………………………………………………………….. G-1
(2) Cylinder Number ………………………………………………………………………………………………… G-2
[2] MOWER IDENTIFICATION ………………………………………………………………………………………. G-2
[3] FRONT LOADER IDENTIFICATION ………………………………………………………………………….. G-2
2. GENERAL PRECAUTIONS ……………………………………………………………………………………………. G-3
3. HANDLING PRECAUTIONS FOR ELECTRICAL PARTS AND WIRING ……………………………… G-4
[1] WIRING …………………………………………………………………………………………………………………. G-4
[2] BATTERY ………………………………………………………………………………………………………………. G-6
[3] FUSE …………………………………………………………………………………………………………………….. G-6
[4] CONNECTOR ………………………………………………………………………………………………………… G-6
[5] HANDLING OF CIRCUIT TESTER ……………………………………………………………………………. G-7
[6] COLOR OF WIRING ……………………………………………………………………………………………….. G-8
4. LUBRICANTS, FUEL AND COOLANT …………………………………………………………………………….. G-9
[1] BX Tractor ……………………………………………………………………………………………………………… G-9
(1) Capacity Table …………………………………………………………………………………………………… G-9
(2) Engine Oil, Fuel and Transmission Oil ………………………………………………………………… G-10
[2] MOWER ………………………………………………………………………………………………………………. G-12
(1) Lubricants ……………………………………………………………………………………………………….. G-12
[3] FRONT LOADER ………………………………………………………………………………………………….. G-12
(1) Lubricants ……………………………………………………………………………………………………….. G-12
5. TIGHTENING TORQUES …………………………………………………………………………………………….. G-13
[1] GENERAL USE SCREWS, BOLTS AND NUTS (TRACTOR AND MOWER) …………………. G-13
[2] GENERAL USE SCREWS, BOLTS AND NUTS (FRONT LOADER) …………………………….. G-14
[3] STUD BOLTS ……………………………………………………………………………………………………….. G-14
[4] METRIC SCREWS, BOLTS AND NUTS …………………………………………………………………… G-15
[5] AMERICAN STANDARD SCREWS, BOLTS AND NUTS WITH UNC OR UNF
THREADS ……………………………………………………………………………………………………………. G-15
[6] PLUGS ………………………………………………………………………………………………………………… G-15
[7] HYDRAULIC FITTINGS …………………………………………………………………………………………. G-16
(1) Adaptors, Elbows and Others …………………………………………………………………………….. G-16
6. MAINTENANCE CHECK LIST ……………………………………………………………………………………… G-17
[1] BX TRACTOR ………………………………………………………………………………………………………. G-17
[2] MOWER ………………………………………………………………………………………………………………. G-18
[3] FRONT LOADER ………………………………………………………………………………………………….. G-19
7. CHECK AND MAINTENANCE ……………………………………………………………………………………… G-20
[1] BX TRACTOR ………………………………………………………………………………………………………. G-20
(1) Daily Check …………………………………………………………………………………………………….. G-20
(2) Check Points of Initial 50 Hours …………………………………………………………………………. G-21
(3) Check Points of Every 50 Hours …………………………………………………………………………. G-23
(4) Check Points of Every 100 Hours ……………………………………………………………………….. G-25
(5) Check Points of Every 200 hours ……………………………………………………………………….. G-30
(6) Check Points of Every 400 Hours ……………………………………………………………………….. G-32
(7) Check Point of Every 500 Hours ………………………………………………………………………… G-34
(8) Check Point of Every 800 Hours ………………………………………………………………………… G-35
(9) Check Point of Every 1500 Hours ………………………………………………………………………. G-35
(1 0)Check Point of Every 3000 Hours ………………………………………………………………………. G-35
(11 )Check Point of Every 1 Year ……………………………………………………………………………… G-35
KiSC issued 12, 2012 A
(12)Check Points of Every 2 Years …………………………………………………………………………… G-35
(13)Others …………………………………………………………………………………………………………….. G-39
[2] MOWER ……………………………………………………………………………………………………………….. G-41
(1) Check Points of Daily or Each Use ……………………………………………………………………… G-41
(2) Check Point of Initial 50 Hours …………………………………………………………………………… G-43
(3) Check Point of Every 150 Hours …………………………………………………………………………. G-43
(4) Check Point of Every 2 Years …………………………………………………………………………….. G-43
[3] FRONT LOADER. ………………………………………………………………………………………………….. G-44
(1) Check Points of Each Use or Daily ……………………………………………………………………… G-44
(2) Check Points of Every 10 Hours …………………………………………………………………………. G-44
8. SPECIAL TOOLS ………………………………………………………………………………………………………… G-45
[1] SPECIAL TOOLS FOR ENGINE ……………………………………………………………………………… G-45
[2] SPECIAL TOOLS FOR TRACTOR ………………………………………………………………………….. G-54
[3] SPECIAL TOOLS FOR LOADER …………………………………………………………………………….. G-59
9. TIRES ……………………………………………………………………………………………………………………….. G-60
[1] TIRE PRESSURE ………………………………………………………………………………………………….. G-60
[2] WHEEL TREAD …………………………………………………………………………………………………….. G-61
(1) Front Wheels …………………………………………………………………………………………………… G-61
(2) Rear Wheels ……………………………………………………………………………………………………. G-62
[3] BALLAST ……………………………………………………………………………………………………………… G-63
(1) Front Ballast. ……………………………………………………………………………………………………. G-63
(2) Rear Ballast …………………………………………………………………………………………………….. G-64
10. IMPLEMENT LIMITATIONS …………………………………………………………………………………………. G-65

IMAGES PREVIEW OF THE MANUAL:

Questions? Email us: [email protected]

PLEASE NOTE:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

S.M