Massey Ferguson EU MF 6700 S Series Classic Version Dyna-4 Dyna-6 Operator’s Manual – PDF DOWNLOAD

Description

Massey Ferguson EU MF 6700 S Classic Version Dyna-4 Dyna-6 Operator’s Manual – PDF DOWNLOAD

DESCRIPTION:

Massey Ferguson EU MF 6700 S Series Classic Version Dyna-4 Dyna-6 Operator’s Manual – PDF DOWNLOAD

Introduction – Safety instructions:
Operator’s Manual:

NOTE: This Operator’s Manual is widely published and distributed and the availability of the attachments indicated, whether fitted to the basic tractor or as an accessory, may vary depending on the country or region in which the tractor is used. To find out which attachments are available in a given region, contact a Massey Ferguson dealer. The purpose of this manual is to enable the owner and the operator to operate the tractor appropriately under normal conditions of use. Providing they follow the instructions carefully, the tractor will give many years of service in the Massey Ferguson tradition.

• Use for any other activity (particularly forestry work) is considered to be contrary to the intended use. The commissioning of equipment by the Massey Ferguson dealer on the user’s premises enables the dealer to ensure that these operating and service instructions are properly understood. Always consult the Massey Ferguson dealer if there is any part of this manual that you do not understand. It is important that these instructions are understood and followed. This manual does not cover all operation and safety instructions relevant to the implements and accessories that may be fitted at the time of tractor delivery or later.
• It is essential that operators use and understand the Operator’s Manuals relating to these implements and accessories. IMPORTANT: This manual must always be kept with the tractor. For extra copies, contact your Massey Ferguson dealer. This chapter in the Operator’s Manual highlights certain basic safety-related situations that may be encountered during normal operation and servicing of the tractor and provides the information needed to handle these situations.

This chapter supplements any safety instructions given in other chapters of this manual. It may be necessary to take additional precautions, depending on the implements and accessories used and the working conditions on-site or in the service area. Massey Ferguson can under no circumstances exercise direct control over the commissioning, operation, inspection, lubrication or servicing of the tractor. It is therefore YOUR responsibility to take suitable safety precautions in such areas.

TABLE OF CONTENTS:

Massey Ferguson EU MF 6700 S Series Classic Version Dyna-4 Dyna-6 Operator’s Manual – PDF DOWNLOAD

Tractor identification 11
1 1 Locating serial numbers 13
1 1 1 Locating serial numbers 13
1 2 Your tractor identification details 15
1 2 1 Your tractor identification details 15
2 Safety instructions and safety points – Warranty 17
2 1 Introduction 19
2 1 1 Introduction – Safety instructions 19
2 2 Safety – Symbols and terms 21
2 2 1 Safety- Symbols and terms 21
2 3 Safety decals and instructions 22
2 3 1 Checking and replacing the safety decals and instructions 22
2 3 2 Presentation and location of the safety decals and instructions 23
2 4 General safety instructions 28
2 4 1 Awareness of the safety instructions and symbols 28
2 4 2 Operator familiarity in the use of the tractor 28
2 4 3 Filling the fuel tank 29
2 4 4 Mounting and dismounting the operator’s seat 29
2 4 5 Mandatory procedure before dismounting the tractor 30
2 5 Special safety instructions for preparing the tractor for use 31
2 5 1 Protective clothing 31
2 5 2 Activated carbon filter information 31
2 5 3 Safety devices and items 34
2 5 4 Checking the tractor 34
2 6 Specific safety instructions for starting the tractor 36
2 6 1 Protection of persons other than the operator 36
2 6 2 Start up safely 36
2 6 3 Starting the tractor with jump start cables 37
2 6 4 Checks to be carried out after start-up 38
2 7 Specific safety instructions for using the tractor 39
2 7 1 General instructions 39
2 7 2 Protection of persons other than the operator 40
2 7 3 Overturning 40
2 7 4 Tractor towing 43
2 7 5 Regulatory data on maximum permitted trailed weights 43
2 7 6 Road use 47
2 7 7 Parking brake 49
2 7 8 Power take-off 49
2 7 9 Implements 50
2 7 10 Front-end loader 52
2 8 Specific safety instructions for servicing the tractor 53
2 8 1 Pollution warning to observe when servicing the tractor 53
2 8 2 General instructions 53
2 8 3 Handling instructions 54
2 8 4 Special instructions for cleaning the tractor 56
2 9 Protective structures 57
2 9 1 Protective structures – Use and accreditation 57
2 9 2 Cab 57
2 9 3 Seat belt 57
MF 6700 S – Operation
ACT001745A_ed3
Table of contents
2 9 4 Instructor seat 58
2 10 Warranty 59
2 10 1 General 59
2 10 2 Pre-delivery inspection and commissioning on the user’s premises 59
2 10 3 Warranty procedure 59
2 10 4 Procedure to follow if changing region 59
2 10 5 Servicing during and after the warranty period 60
2 10 6 California emission control warranty statement 60
2 10 7 Emission reduction warranty statement for the United States and Canada 63
3 Usage 69
3 1 Standard cab 73
3 1 1 Steering console 73
3 1 2 Instrument panel 74
3 1 3 Control unit 80
3 1 4 Pedals 81
3 1 5 Steering wheel 81
3 1 6 Operator presence detector 82
3 1 7 Automatic adjustment pneumatic seat 86
3 1 8 Manual adjustment pneumatic seat 92
3 1 9 Instructor seat 97
3 1 10 Right-hand console 97
3 1 11 Right-hand pillar 98
3 1 12 Left-hand console 98
3 1 13 Upper console 99
3 1 14 Manual air conditioning 101
3 1 15 Additional heater 106
3 1 16 Accessories sockets 106
3 1 17 Emergency exits 107
3 1 18 Sun visor 107
3 1 19 Wheel chock(s) (optional) 108
3 2 Setup and Information Screen control screens on the instrument
panel 110
3 2 1 Using the Setup and Information Screen 110
3 2 2 Setup and Information screens 112
3 3 Body 119
3 3 1 Opening the bonnet 119
3 3 2 Adjusting the external rear-view mirrors 119
3 3 2 1 Positioning the arms 119
3 3 2 2 Adjusting the arm extensions (depending on model) 120
3 3 2 3 Adjusting the rear-view mirrors (depending on model) 120
3 4 Engine 121
3 4 1 Running-in 121
3 4 2 Filling with fuel 121
3 4 3 Start switch 123
3 4 4 Start-up 123
3 4 5 Starting the SCR Technology engine in cold weather 124
3 4 6 Information about the various operating modes of the SCR Technology engine 126
3 4 7 Stopping the engine 131
3 4 8 Engine speed 131
3 4 9 Storing an engine speed 133
3 5 Transmission 135
3 5 1 Presentation of the different driving modes 135
3 5 2 Clutch function 135
3 5 3 PowerShuttle 136
3 5 3 1 PowerShuttle Protection Function 137
3 5 4 Adjusting the start ratios (1A, 1 B, 1 C etc ) 138
MF 6700 S – Operation
ACT001745A_ed3
3 6
3 7
3 8
Table of contents
3 5 4 1 Setting procedure: 138
3 5 4 2 Starting ratio 138
3 5 5 Lever (Speedmatching) mode 139
3 5 6 Pedal (AutoDrive) mode 140
3 5 7 Road mode (Hare)/Field mode (Tortoise) 141
3 5 8 Changing the transmission ratios (1 A, 1 B, 1 C, etc ) 142
3 5 9 Optional creeper range (snail) 142
3 5 10 Tractor towing 143
3 5 11 Forward speed calibration 143
Brakes 145
3 6 1 Brake pedals 145
3 6 2 Hydraulic trailer brake 145
3 6 3 Pneumatic trailer brake 146
3 6 4 Parking brake 147
Front axle 149
3 7 1 Four-wheel drive front axle 149
3 7 2 Suspended front axle 150
3 7 3 Permissible load on the front axle 152
Differential lock 155
3 8 1 Differential lock 155
3 9 Power take-off 157
3 9 1 Front power take-off 157
3 9 2 Rear power take-off (PTO) 157
3 9 2 1 Selecting the power take-off speed 158
3 9 2 2 Adjusting the progressivity of power-take-off engagement 159
3 9 2 3 Engaging PTO in manual mode: 160
3 9 2 4 Engaging PTO in automatic mode: 160
3 9 3 Economy PTO 161
3 9 4 GSPTO (optional) 162
3 9 5 Replacing the interchangeable shaft 163
3 9 6 Changing the flanged shaft 164
3 9 7 PTO external control 164
3 9 8 Power take-off electronic controls 165
3 9 9 Power take-off protection 166
3 1 O Linkage 168
3 10 1 General 168
3 10 2 Rear linkage electronic controls 169
3 10 3 Rear linkage operation 171
3 10 4 Rear linkage external controls 176
3 10 5 Front linkage 177
3 10 6 Top link 180
3 10 7 Bottom links 182
3 10 8 Lift rods 183
3 10 9 Stabilizers 184
3 10 9 1 Stabilizers with manual telescopic adjustment 184
3 10 9 2 Automatic stabilizers 186
3 10 9 3 Stabilizers with shoes 186
3 10 10 Ball joint support 187
3 11 Towing equipment 188
3 11 1 General 188
3 11 2 Swinging drawbar 193
3 11 2 1 Fitting the swinging drawbar 194
3 12 Auxiliary hydraulics 195
3 12 1 General 195
3 12 2 Description of hydraulic couplers on Open Center system 195
3 12 3 Use of hydraulic couplers on Open Center system 196
3 12 4 Description of hydraulic couplers on Closed Center system (Load Sensing) 199
MF 6700 S – Operation
ACT001745A_ed3
Table of contents
3 12 5 Use of hydraulic couplers on Closed Center system (Load Sensing) 201
3 12 6 Description of the hydraulic controls inside the cab 205
3 12 7 Hydraulics control lever 206
3 12 8 Open Centre 100 I/min (26 4 gal/min (US)) 207
3 12 8 1 Pump coupling (combined flow) 207
3 12 8 2 Pump uncoupling 208
3 12 9 Setting flow rates 208
3 13 Standard front-end loader function 209
3 13 1 Front-end loader 209
3 13 2 Layout of components 209
3 13 3 Standard front-end loader connection 210
3 13 4 Using the mechanical joystick of the front-end loader 211
3 13 4 1 Locking/unlocking the front-end loader control 211
3 13 4 2 Joystick in working position 211
3 13 4 3 Joystick in rest position 212
3 13 4 4 Joystick functions for the front-end loader 212
3 13 4 5 Electrical functions for the front-end loader 212
3 13 4 6 Floating position 213
3 13 4 7 3rd and 4th functions 213
3 13 4 8 Arm suspension 214
3 13 4 9 Locking and unlocking accessories 214
3 14 Lighting 215
3 14 1 Main lighting control module 215
3 14 2 Work lights module 216
3 15 Suspended cab 218
3 15 1 Suspended cab 218
3 16 Front tires and track widths 221
3 16 1 Wheel studs 221
3 16 2 Installation points of the axle stands 221
3 16 3 Adjusting the front wheel track width 222
3 16 4 Adjusting the 4WD front axle stops 225
3 16 4 1 Fitting the oscillation stops 225
3 16 4 2 Adjusting the steering angle 225
3 16 4 3 Toe-in check 226
3 16 4 4 Adjusting the front fenders Shoe side adjustment on the front axle 226
3 16 4 5 Adjusting the front fenders Adjusting the lateral position of the fender
on the support (two adjustments are possible) 227
3 16 4 6 Adjusting the front fenders Adjusting the height of the support on the
shoe 227
3 16 5 Tires 227
3 16 6 Tire pressures 227
3 17 Rear tires and track widths 228
3 17 1 Wheel studs 228
3 17 2 Installation points of the axle stands 228
3 17 3 Rear track width with flanged shafts 229
3 17 4 Rear track width with short straight shafts 231
3 17 5 Rear track width with long straight shafts 235
3 17 6 Adjusting the rear wheel track width 237
3 17 6 1 Adjustment of wheel position on the straight shaft 238
3 17 6 2 Adjustment of wheel position on the straight shaft 238
3 18 Dual wheels 240
3 18 1 Dual wheels 240
3 18 2 Installation points of the axle stands 241
3 18 3 Dual rear wheel track width with long straight shafts 242
3 18 4 Adjusting the rear wheel track width 247
3 18 4 1 Adjustment of wheel position on the straight shaft 248
3 18 4 2 Adjustment of wheel position on the straight shaft 248
MF 6700 S – Operation
ACT001745A_ed3
Table of contents
3 19 Ballast 250
3 19 1 Liquid ballasting 250
3 19 2 Front-end weight 250

MASSEY FERGUSON EU MF 6700 S SERIES CLASSIC VERSION DYNA-4 DYNA-6 OPERATOR’S MANUAL – PDF DOWNLOAD:

IMAGES PREVIEW OF THE MANUAL:

PLEASE NOTE:

• This is the SAME MANUAL used by the dealerships to diagnose your vehicle
• No waiting for couriers / posts as this is a PDF manual and you can download it within 2 minutes time once you make the payment.
• Your payment is all safe and the delivery of the manual is INSTANT – You will be taken to the DOWNLOAD PAGE.
• So have no hesitations whatsoever and write to us about any queries you may have : heydownloadss @gmail.com

S.V