Massey Ferguson EU Tractor 7400 Series 7465 7475 7480 7485 7490 7495 7497 7499 Service Manual – PDF

Description

Massey Ferguson EU Tractor 7400 Series 7465 7475 7480 7485 7490 7495 7497 7499 Service Manual – PDF DOWNLOAD

DESCRIPTION:

Massey Ferguson EU Tractor 7400 Series 7465 7475 7480 7485 7490 7495 7497 7499 Service Manual – PDF DOWNLOAD

Part No. 3378553M7

Using the manual:
General
The purpose of this manual is to assist Dealers and Agents in the installation, servicing and repair of Massey Ferguson equipment. It is important to follow the methods shown and to use special tools in order to perform the operations within the times stated in the repair time schedule.

Service tools:
Where the use of a service tool is necessary to carry out an operation, the tool reference is mentioned with the relevant instruction. Tool drawings for makeshift tools are given at the end of the relevant sections.
Repairs and parts replacement:
During replacement operations, it is essential that only genuine Massey Ferguson parts are used. If non-genuine Massey Ferguson parts are fitted, the tractor warranty may be invalidated and tractor safety may be compromised. All Massey Ferguson parts are guaranteed by the manufacturer. Massey Ferguson Dealers and Agents are required to supply only genuine service parts. When carrying out repairs and fitting replacement parts and accessories, the following points are of particular importance:
– Legislation in certain countries prohibits the fitting of parts that do not comply with the tractor manufacturer’s specifications
– Torque wrench setting figures given in the workshop manual must be strictly respected
– Locking devices must be fitted where specified. If the efficiency of a locking device is impaired during disassembly, it must be replaced.

TABLE OF CONTENTS:

Massey Ferguson EU Tractor 7400 Series 7465 7475 7480 7485 7490 7495 7497 7499 Service Manual – PDF DOWNLOAD

1 Introduction
7400 series tractors
1A10 7400 series tractors – General
1A11 7400 series tractors – Error codes
1A12 7400 series tractors – Electrical and hydraulics diagrams
1A16 7400 series tractors – Adjustments, bleeding and calibrations
2 Separation of assemblies
3 Engine
See existing chapter in manual 3378553M4
3A10 Sisu Tier 3 engine – General
3A11 Sisu Tier 3 engine – Error codes
3A12 Sisu Tier 3 engine – Electrical and hydraulics diagrams
3A13 Sisu Tier 3 engine – Layout of components
3A14 Sisu Tier 3 engine – Tests and diagnostics
3A15 Sisu Tier 3 engine – Programming and setting parameters
3A16 Sisu Tier 3 engine – Adjustments, bleeding and calibrations
3A17 Sisu Tier 3 engine – Disassembly and reassembly
3A 18 Sisu Tier 3 engine – Service tools
4 Clutch
Chapter intentionally left blank
5 Gearbox
5A10 ML 130/ML 160 – General
5A11 ML130/ML160 – Error codes
5A12 ML130/ML160 – Electrical and hydraulics diagrams
5A14 ML130/ML160 – Tests and diagnostics
5A15 ML130/ML160 – Programming and setting parameters
5A 16 ML 130/ML 160 – Adjustments, bleeding and calibrations
5A17 ML130/ML160 – Disassembly and reassembly
5A18 ML 130/ML 160 – Service tools
6 Rear axle
6A 11 HA 130/160 – Error codes
6A15 HA130/160 – Programming and setting parameters
6A 16 HA 130/160 – Adjustments, bleeding and calibrations
6A23 HA130/160/Final drives – Layout of components
6A25 HA130/160/Final drives – Programming and setting parameters
6A27 HA130/160/Final drives – Disassembly and reassembly
6A31 HA 130/160/Differential – Error codes
6A32 HA130/160/Differential – Electrical and hydraulics diagrams
6A33 HA 130/160/Differential – Layout of components
6A34 HA130/160/Differential – Tests and diagnostics
6A35 HA130/160/Differential – Programming and setting parameters
6A36 HA130/160/Differential – Adjustments, bleeding and calibrations
6A37 HA130/160/Differential – Disassembly and reassembly
HA 130/160/Tractor braking – Error codes
HA 130/160/Tractor braking – Electrical and hydraulics diagrams
HA 130/160/Tractor braking – Layout of components
HA 130/160/Tractor braking – Disassembly and reassembly
HA 130/160/ParkLock – General
HA 130/160/ParkLock – Error codes
HA 130/160/ParkLock – Electrical and hydraulics diagrams
HA 130/160/ParkLock – Layout of components
HA130/160/ParkLock – Tests and diagnostics
HA130/160/ParkLock – Programming and setting parameters
HA 130/160/ParkLock – Adjustments, bleeding and calibrations
HA 130/160/Hydraulic trailer braking – Error codes
HA 130/160/Hydraulic trailer braking – Electrical and hydraulics
diagrams
6A64 HA 130/160/Hydraulic trailer braking – Tests and diagnostics
6A65 HA130/160/Hydraulic trailer braking – Programming and setting
parameters
6A70 HA 130/160/Pneumatic trailer braking – General
6A72 HA 130/160/Pneumatic trailer braking – Electrical and hydraulics
6A73
6A74
6A76
diagrams
HA 130/160/Pneumatic trailer braking – Layout of components
HA 130/160/Pneumatic trailer braking – Tests and diagnostics
HA 130/160/Pneumatic trailer braking – Adjustments, bleeding and
calibrations
6A82 HA130/160/Auto-hitch – Electrical and hydraulics diagrams
Power take-off
7 A 11 HA 130/160/Power take-off – Error codes
7A12 HA130/160/Power take-off – Electrical and hydraulics diagrams
7 A 13 HA 130/160/Power take-off – Layout of components
7A14 HA130/160/Power take-off- Tests and diagnostics
7 A 15 HA 130/160/Power take-off – Programming and setting parameters
7 A 16 HA 130/160/Power take-off – Adjustments, bleeding and calibrations
7A17 HA130/160/Power take-off- Disassembly and reassembly
7B10 Zuidberg front power take-off – General
7B12 Zuidberg front power take-off – Electrical and hydraulics diagrams
7B13 Zuidberg front power take-off – Layout of components
7B14 Zuidberg front power take-off – Tests and diagnostics
7B16 Zuidberg front power take-off – Adjustments, bleeding and
calibrations
Front axle
8A11 DANA 735 – Error codes
8A12 DANA 735 – Electrical and hydraulics diagrams
8A14 DANA 735 – Tests and diagnostics
8A15 DANA 735 – Programming and setting parameters
8A16 DANA 735 – Adjustments, bleeding and calibrations
8A17 DANA 735 – Disassembly and reassembly
8B11 DANA 740 – Error codes
8B12 DANA 740 – Electrical and hydraulics diagrams
8B14 DANA 740 – Tests and diagnostics
8B15 DANA 740 – Programming and setting parameters
8B16 DANA 740 – Adjustments, bleeding and calibrations
MASSEY FERGUSON
7400 series tractors
Table of contents
8817 DANA 740 – Disassembly and reassembly
8C11 DANA 745 – Error codes
8C12 DANA 745 – Electrical and hydraulics diagrams
8C14 DANA 745 – Tests and diagnostics
8C15 DANA 745 – Programming and setting parameters
8C16 DANA 745 – Adjustments, bleeding and calibrations
8C17 DANA 745 – Disassembly and reassembly
8D11 DANA 750 – Error codes
8D12 DANA 750 – Electrical and hydraulics diagrams
8D14 DANA 750 – Tests and diagnostics
8D15 DANA 750 – Programming and setting parameters
8D16 DANA 750 – Adjustments, bleeding and calibrations
8D17 DANA 750 – Disassembly and reassembly
8E11 DANA 755 – Error codes
8E12 DANA 755 – Electrical and hydraulics diagrams
8E14 DANA 755 – Tests and diagnostics
8E15 DANA 755 – Programming and setting parameters
8E16 DANA 755 – Adjustments, bleeding and calibrations
8E17 DANA 755 – Disassembly and reassembly
8G11 4WD clutch – Error codes
8G12 4WD clutch – Electrical and hydraulics diagrams
8G14 4WD clutch – Tests and diagnostics
8G15 4WD clutch – Programming and setting parameters
8G16 4WD clutch – Adjustments, bleeding and calibrations
9 Hydraulics
See existing chapter in manual 3378553M4
1 0 Electricity
10A12 Lighting and equipment – Electrical and hydraulics diagrams
10A13 Lighting and equipment – Layout of components
10810 Fuse box – General
10812 Fuse box – Electrical and hydraulics diagrams
10813 Fuse box – Layout of components
10817 Fuse box – Disassembly and reassembly
10C14 Alternator – Tests and diagnostics
10C17 Alternator – Disassembly and reassembly
1OC18 Alternator – Service tools
10E10 Starter – General
1 0E14 Starter – Tests and diagnostics
10E17 Starter – Disassembly and reassembly
1 1 Electronics
11A10 DCC2 – General
11A11 DCC2 – Error codes
11A12 DCC2 – Electrical and hydraulics diagrams
11A15 DCC2 – Programming and setting parameters
11810 Datatronic 3 – General
11812 Datatronic 3 – Electrical and hydraulics diagrams
11815 Datatronic 3 – Programming and setting parameters
Datatronic 3 – Adjustments, bleeding and calibrations
11C12 I so bus – Electrical and hydraulics diagrams
11D12 Auto-Guide – Electrical and hydraulics diagrams
11 D14 Auto-Guide – Tests and diagnostics
5
7400 series tractors
Table of contents MASSEY FERGUSON
11D15 Auto-Guide – Programming and setting parameters
11D16 Auto-Guide – Adjustments, bleeding and calibrations
11 D17 Auto-Guide – Disassembly and reassembly
11D18 Auto-Guide – Service tools
12 Cab
12A10 Standard air conditioning – General
12A12 Standard air conditioning – Electrical and hydraulics diagrams
12A14 Standard air conditioning – Tests and diagnostics
12A16 Standard air conditioning – Adjustments, bleeding and calibrations
12B10 Self-regulating air conditioning – General
12B11 Self-regulating air conditioning – Error codes
12B12 Self-regulating air conditioning – Electrical and hydraulics diagrams
12B14 Self-regulating air conditioning – Tests and diagnostics
12B16 Self-regulating air conditioning – Adjustments, bleeding and
calibrations
1 3 Accessories
See existing chapter in manual 3378553M4
1 4 Service tools
14A01 General
14A03 Engine
14A05 Gearbox
14A06 Rear axle
14A11 Electronics

MASSEY FERGUSON EU TRACTOR 7400 SERIES 7465 7475 7480 7485 7490 7495 7497 7499 SERVICE MANUAL – PDF:

IMAGES PREVIEW OF THE MANUAL:

PLEASE NOTE:

• This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
• Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.

S.V