New Holland E18C Mini Excavator Operator’s Manual 51557403 – PDF DOWNLOAD

Description

New Holland E18C Mini Excavator Operator’s Manual 51557403 – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

New Holland E18C Mini Excavator Operator’s Manual 51557403 – PDF DOWNLOAD

GENERAL INFORMATION:
Note to the Owner:
Improper operation of this machine can cause injury or death. Before using this machine, make certain that every
operator:
• Is instructed in safe and proper use of the machine.
• Reads and understands the Manual(s) pertaining to the machine.
• Reads and understands ALL Safety Decals on the machine.
• Clears the area of other persons.
• Learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site.

• It is your responsibility to observe pertinent laws and regulations and follow NEW HOLLAND CONSTRUCTION instructions
  on machine operation and maintenance.
• Your machine has been designed and built to the highest standards of quality. It conforms to all current safety regulations.
• However, the risk of accidents can never be completely excluded. That is why it is essential to observe
  elementary safety rules and precautions.
• Read this manual carefully, paying particular attention to the instructions concerning safety, operation and maintenance
  so as to avoid the risk of injury while operating or servicing the machine.
• The standard attachments and tools of this machine are designed to carry out earthmoving and rehandling operations.
• If you want to use this machine to handle a load (pipes, culverts, formwork, etc.), make sure that it is designed to
  carry out this kind of work. For this type of application, the machine must be equipped with safety valves, an overload
  indicator, a load handling chart corresponding to the type of machine and its attachment, and a load fixing point. All
  legal requirements must also be strictly observed.
• Do not use this machine for any application or purpose other than those described in this manual. If the machine is to
  be used for work involving the use of special attachments, accessories, or equipment, consult your NEW HOLLAND
  CONSTRUCTION Dealer in order to make sure that any adaptations or modifications made are in keeping with the
  machine’s technical specifications and with prevailing safety requirements.
• Any modification or adaptation which is not approved by NEW HOLLAND CONSTRUCTION may invalidate the machine’s initial conformity with safety requirements.

TABLE OF CONTENTS:

New Holland E18C Mini Excavator Operator’s Manual 51557403 – PDF DOWNLOAD

1 GENERAL INFORMATION
Note to the Owner 1-1
Intended use 1-2
Electro-Magnetic Compatibility (EMC) 1-2
Telematics (optional) 1-2
Manual scope and required training level 1-3
Product identification 1-5
Operator’s manual storage on the machine 1-9
Machine orientation 1-10
Machine components 1-11
Emissions overview 1-14
2 SAFETY INFORMATION
Signal word definitions 2-1
Safety rules – Utility precautions 2-2
Safety rules 2-3
Ecology and environment 2-12
Hand signals 2-13
Safety signs 2-17
3 CONTROLS AND INSTRUMENTS
Access to operator’s platform
Door and steps 3-1
Operator’s seat
Operator’s seat 3-4
Forward controls
Forward controls 3-6
Windshield 3-13
Left-hand side controls
Left-hand side controls 3-14
Safety lock lever 3-15
Engine speed control lever 3-15
Emergency exit hammer 3-16
Windshield washer reservoir 3-16
Right-hand side controls
Right-hand side controls 3-17
Dozer blade control lever 3-20
Instrument cluster 3-25
Ventilation and heating 3-30
Rearward controls
Storage compartment 3-31
Overhead controls
Cab internal lighting 3-31
Radio 3-32
Exterior controls
Side doors 3-43
Rear view mirrors 3-44
Battery disconnect switch 3-46
Fuel tank 3-47
4 OPERATING INSTRUCTIONS
Starting the unit
Anti-theft protection 4-1
Starting the engine 4-3
Bringing the machine up to operating temperature 4-5
Operating the machine in hot or cold weather 4-6
Operating the machine 4-7
Lowering the attachment in the event of a failure 4-11
Bucket replacement 4-12
Hydraulic control lever operating pattern 4-13
Caution while using rubber crawlers 4-16
Stopping the unit
Stopping the engine 4-20
Moving the unit
Machine travel 4-21
Parking the unit
Parking the machine 4-27
5 TRANSPORT OPERATIONS
Road transport
Loading the machine onto a transport trailer 5-1
Preparing for road transport
Tie downs for shipping 5-3
Unloading the machine from a transport trailer 5-4
Shipping transport
Handling the machine 5-5
Recovery transport
Towing the machine 5-7
6 MAINTENANCE
General information
Basic instructions 6-1
General specification – Biodiesel fuels 6-4
General specification – Diesel fuel 6-6
Fluids and lubricants 6-7
Releasing pressure in the hydraulic system 6-11
Fuel system bleeding 6-14
Protecting the electronic and electrical systems during battery charging or welding 6-15
Maintenance planning
Maintenance chart 6-16
Break-in period
Engine oil and filter 6-18
Fuel filter 6-18
Travel reduction gears 6-18
Grease points (Bucket) 6-18
Grease points (Boom and arm) 6-18
Grease points (Blade) 6-19
Grease points (Boom swing cylinder) 6-19
Grease points (Extension cylinder) 6-19
Tightening torques 6-19
Every 10 hours
Engine oil level 6-20
Engine coolant level 6-21
Hydraulic oil level 6-22
Fuel filter water separator 6-24
Fan and alternator drive belt 6-25
Every 50 hours
Grease points (Bucket) 6-26
Grease points (Blade) 6-27
Grease points (Extension cylinder) 6-28
Track tension 6-29
Swing ring gear 6-31
Fuel tank 6-32
Every 100 hours
Fuel filter water separator 6-33
Every 250 hours
Engine oil and filter 6-34
Battery 6-36
Grease points (Boom and arm) 6-41
Swing bearing 6-42
Boom swing cylinder 6-43
Hydraulic oil return filter 6-44
Tightening torques 6-46
Every 400 hours
Fuel filter 6-47
Every 500 hours
Radiator and coolers 6-48
Radiator fan 6-50
Air cleaner 6-51
Every 1000 hours
Travel reduction gears 6-54
Every 2000 hours
Engine coolant 6-55
Hydraulic oil suction filter 6-57
Oil reservoir – Check 6-58
Air cleaner 6-59
Every 5000 hours
Hydraulic oil 6-61
When necessary
Bulb replacement 6-63
Cab air filter 6-65
Fuel tank strainer 6-65
Control levers 6-66
Plastic and resin parts 6-66
Fuse and relay locations
Fuses 6-67
Storage
Preparing for storage 6-69
Periodic checks 6-70
Starting up the machine after storage 6-71
7 TROUBLESHOOTING
Fault code resolution
Engine – Troubleshooting 7-1
Electrical systems – Troubleshooting 7-2
Other systems – Troubleshooting 7-3
8 SPECIFICATIONS
Machine specifications 8-1
Dimensions 8-3
Weights 8-6
9 ACCESSORIES
Auxiliary hydraulic circuits 9-1
Hydraulic oil – breaker/nibbler 9-8
Rotating beacon 9-9
Fire extinguisher 9-10

Customer Support: [email protected]

PLEASE NOTE:

• This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
• This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
• Require some other service manual or have any queries: please WRITE to us at [email protected]

S.V