New Holland E26C Mini Excavators Operator’s Manual 51698709 – PDF DOWNLOAD

Description

New Holland E26C Mini Excavators Operator’s Manual 51698709 – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

New Holland E26C Mini Excavators Operator’s Manual 51698709 – PDF DOWNLOAD

GENERAL INFORMATION:
Note to the Owner:
Improper operation of this machine can cause injury or death. Before using this machine, make certain that every
operator:
• Is instructed in safe and proper use of the machine.
• Reads and understands the Manual(s) pertaining to the machine.
• Reads and understands ALL Safety Decals on the machine.
• Clears the area of other persons.
• Learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site.

• It is your responsibility to observe pertinent laws and regulations and follow NEW HOLLAND CONSTRUCTION instructions
  on machine operation and maintenance.
• Your machine has been designed and built to the highest standards of quality. It conforms to all current safety regulations.
• However, the risk of accidents can never be completely excluded. That is why it is essential to observe
  elementary safety rules and precautions.
• Read this manual carefully, paying particular attention to the instructions concerning safety, operation and maintenance
  so as to avoid the risk of injury while operating or servicing the machine.
• The standard attachments and tools of this machine are designed to carry out earthmoving and rehandling operations.
• If you want to use this machine to handle a load (pipes, culverts, formwork, etc.), make sure that it is designed to
  carry out this kind of work. For this type of application, the machine must be equipped with safety valves, an overload
  indicator, a load handling chart corresponding to the type of machine and its attachment, and a load fixing point. All
  legal requirements must also be strictly observed.
• Do not use this machine for any application or purpose other than those described in this manual. If the machine is to
  be used for work involving the use of special attachments, accessories, or equipment, consult your NEW HOLLAND
  CONSTRUCTION Dealer in order to make sure that any adaptations or modifications made are in keeping with the
  machine’s technical specifications and with prevailing safety requirements.
• Any modification or adaptation which is not approved by NEW HOLLAND CONSTRUCTION may invalidate the machine’s
  initial conformity with safety requirements.
• The machine must undergo regular inspections, the frequency of which varies according to the type of use. Consult
  your NEW HOLLAND CONSTRUCTION Dealer.

TABLE OF CONTENTS:

New Holland E26C Mini Excavators Operator’s Manual 51698709 – PDF DOWNLOAD

1 GENERAL INFORMATION
Note to the Owner 1-1
Intended use 1-2
Electro-Magnetic Compatibility (EMC) 1-2
Telematics (optional) 1-2
Manual scope and required training level 1-3
Product identification 1-5
Operator’s manual storage on the machine 1-8
Machine orientation 1-9
Machine components 1-10
EC Declaration of Conformity 1-12
2 SAFETY INFORMATION
Signal word definitions 2-1
Safety rules 2-2
Ecology and environment 2-11
Hand signals 2-12
Noise emission 2-16
Vibration levels 2-17
Safety signs 2-18
3 CONTROLS AND INSTRUMENTS
Access to operator’s platform
Door and steps 3-1
Operator’s seat
Operator’s seat 3-4
Forward controls
Forward controls 3-6
Windshield 3-11
Left-hand side controls
Left-hand side controls 3-12
Safety lock lever 3-13
Engine speed control lever 3-13
Emergency exit hammer 3-14
Windshield washer reservoir 3-15
Right-hand side controls
Right-hand side controls 3-16
Dozer blade control lever 3-19
Instrument cluster 3-20
Ventilation and heating 3-25
Rearward controls
Storage compartment 3-27
Overhead controls
Cab internal lighting 3-28
Radio 3-29
Exterior controls
Side doors 3-40
Rear view mirrors 3-43
Battery disconnect switch 3-45
Fuel tank 3-46
4 OPERATING INSTRUCTIONS
Starting the unit
Anti-theft protection 4-1
Starting the engine 4-3
Bringing the machine up to operating temperature 4-5
Operating the machine in hot or cold weather 4-6
Operating the machine 4-7
Lowering the attachment in the event of a failure 4-11
Bucket replacement 4-12
Caution while using rubber crawlers 4-13
Stopping the unit
Stopping the engine 4-17
Moving the unit
Machine travel 4-18
Parking the unit
Parking the machine 4-24
5 TRANSPORT OPERATIONS
Road transport
Loading the machine onto a transport trailer 5-1
Preparing for road transport
Tie downs for shipping 5-3
Unloading the machine from a transport trailer 5-4
Shipping transport
Handling the machine 5-5
Recovery transport
Towing the machine 5-7
6 MAINTENANCE
General information
Basic instructions 6-1
General specification – Biodiesel fuels 6-4
Fluids and lubricants 6-6
Releasing pressure in the hydraulic system 6-10
Fuel system bleeding 6-14
Protecting the electronic and electrical systems during battery charging or welding 6-15
Maintenance planning
Maintenance chart 6-16
Break-in period
Grease points (Bucket) 6-18
Grease points (Boom and arm) 6-18
Grease points (Blade) 6-18
Tightening torques 6-18
Fuel filter 6-18
Hydraulic oil return filter 6-18
Pilot line filter 6-19
Travel reduction gears 6-19
Boom swing cylinder 6-19
Every 10 hours
Engine oil level 6-20
Engine coolant level 6-21
Hydraulic oil level 6-22
Fuel filter water separator 6-23
Fan and alternator drive belt 6-24
Every 50 hours
Grease points (Bucket) 6-26
Grease points (Blade) 6-27
Track tension 6-28
Swing ring gear 6-30
Fuel tank drain 6-31
Every 100 hours
Fuel filter water separator 6-32
Every 250 hours
Engine oil and filter 6-32
Battery 6-35
Swing bearing 6-38
Boom swing cylinder 6-39
Tightening torques 6-40
Grease points (Boom and arm) 6-41
Every 400 hours
Fuel filter 6-42
Every 500 hours
Air cleaner 6-44
Radiator and coolers 6-47
Every 750 hours
Valve clearance 6-48
Every 1000 hours
Hydraulic oil return filter 6-49
Pilot line filter 6-50
Travel reduction gears 6-52
Every 1500 hours
Injection nozzle 6-53
Every 2000 hours
Air cleaner 6-53
Engine coolant 6-55
Hydraulic oil suction filter 6-58
Hydraulic hoses 6-59
Biodegradable hydraulic oil 6-60
Every 3000 hours
Injection pump 6-62
Fuel injection system 6-62
Every 5000 hours
Hydraulic oil 6-63
When necessary
Cab and working lights 6-65
Cab air filter 6-68
Fuel tank strainer 6-69
Control levers 6-70
Plastic and resin parts 6-70
Fuse and relay locations
Fuses 6-71
Storage
Preparing for storage 6-73
Periodic checks 6-74
Starting up the machine after storage 6-75
7 TROUBLESHOOTING
Fault code resolution
Engine – Troubleshooting 7-1
Electrical systems – Troubleshooting 7-2
Other systems – Troubleshooting 7-3
8 SPECIFICATIONS
Machine specifications 8-1
Dimensions 8-3
Weights 8-6
9 ACCESSORIES
Direct fit buckets 9-1
Klac type buckets 9-4
Auxiliary hydraulic circuits 9-6
Hydraulic oil – breaker 9-17
Quick coupling system – Klac type 9-18
Load handling 9-28
Thumb bracket 9-31
Rotating beacon 9-32
Fire extinguisher 9-33

Questions? Email us: [email protected]

https://vimeo.com/730567307

PLEASE NOTE:

• This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
• This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
• Require some other service manual or have any queries: please WRITE to us at [email protected]

S.V