New Holland E75CSR Midi Excavator Operator’s Manual 47488357 – PDF DOWNLOAD

Description

New Holland E75CSR Midi Excavator Operator’s Manual 47488357 – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

New Holland E75CSR Midi Excavator Operator’s Manual 47488357 – PDF DOWNLOAD

GENERAL INFORMATION:
Note to the Owner:

• This manual is designed as a guide for the correct and safe use of the machinery and for its correct maintenance.
• Always following the rules in the manual guarantees the best performance, operating economy and a long life for
  the machine and also makes it possible to avoid the most common causes of accidents that may occur during work
  or maintenance operations. Read the manual carefully, paying special attention to the instructions regarding safety,
  operation and maintenance to prevent risks or injury during usage or when carrying out maintenance operations on
  the machine.
• Before handing the machine over to an operator, check that:
  • The operator has been properly trained in the correct and safe use of the machine.
  • Also make sure that the operator has read the instructions in this manual and that they understand them fully.
• Always keep this manual in the cab. Make sure that it is always intact and in good condition. Contact the Dealer for
  further copies or a translation into a different language from the country of use.
• The machine has been designed and constructed in accordance with the most rigorous standards of quality and in
  compliance with current safety regulations. Never use the machine for applications not included in the manual. If the
  machine needs to be used for work that involves the use of special equipment, accessories or instruments, consult
  the Dealer to make sure that any adaptations or modifications carried out comply with the technical specifications of
  the machine and with the safety standards. Any modification or adaptation that is not approved by the manufacturer
  may invalidate the original conformity of the machine to the safety requirements and the persons that carry out these
  unapproved modifications will be held responsible for the consequences.

TABLE OF CONTENTS:

New Holland E75CSR Midi Excavator Operator’s Manual 47488357 – PDF DOWNLOAD

1 GENERAL INFORMATION
Note to the Owner 1-1
Product identification 1-3
Vibration to the operator 1-6
Noise level 1-7
Cab protection (ROPS and FOPS) 1-8
Operator’s manual storage 1-9
2 SAFETY INFORMATION
General safety information 2-1
Warning labels and decals 2-4
Pre-start safety 2-15
Use safety valve and overload alarm 2-49
Handling of accumulator 2-49
3 CONTROLS/INSTRUMENTS
ACCESS TO OPERATOR’S PLATFORM
Cab 3-1
Emergency escape from cab 3-3
OPERATOR’S SEAT
Operator seat 3-4
Seat belt 3-6
FORWARD CONTROLS
Console Front console – Localisation overview 3-7
Instrument cluster 3-11
Offset boom controls 3-28
RIGHT-HAND SIDE CONTROLS
Right hand side controls 3-48
Radio 3-51
Air conditioner 3-60
REARWARD CONTROLS
Console – Operating 3-69
4 OPERATING INSTRUCTIONS
COMMISSIONING THE UNIT
Machine operation 4-1
Checking before starting engine 4-2
Fuel pump 4-8
Adjusting operator seat 4-10
Adjusting mirror 4-11
Checking function of gauge cluster 4-12
Checking work light 4-12
STARTING THE UNIT
Starting engine 4-13
Inspection after starting engine 4-16
Machine warming-up 4-17
Selection of work mode and switching of the attachment mode 4-19
STOPPING THE UNIT
Stopping machine engine 4-22
PARKING THE UNIT
Parking the machine 4-23
5 TRANSPORT OPERATIONS
ROAD TRANSPORT
Machine preparation 5-1
Loading/unloading the machine 5-2
PREPARING FOR ROAD TRANSPORT
Securing the machine 5-5
Unloading the machine 5-6
SHIPPING TRANSPORT
Lifting machine 5-7
RECOVERY TRANSPORT
Installation and removal of mirror for safety 5-9
6 WORKING OPERATIONS
GENERAL INFORMATION
Controls decal 6-1
Machine operation 6-3
Dozer operation 6-9
Practices to improve efficiency 6-10
Hand signals 6-13
Lowering attachment when sudden engine failure occurs 6-19
Machine operation in adverse weather conditions 6-22
Towing the machine 6-23
7 MAINTENANCE
GENERAL INFORMATION
General information 7-1
General safety and precautions 7-2
Maintenance parts 7-8
Torque values for specified 7-9
Torque specifications for bolts and nuts 7-11
Torque specifications for joints and hydraulic hoses 7-14
MAINTENANCE CHART
Maintenance Chart 7-17
PRE-START (EVERY 8 HOURS)
General check 7-19
Dozer lubrication 7-20
EVERY 50 HOURS (WEEKLY)
Batteries 7-21
Fuel tank drain 7-23
Track tension 7-24
EVERY 100 HOURS
Lubrication for Bucket Pin 7-25
EVERY 120 HOURS
Swing motor reduction oil 7-26
Travel reduction unit oil 7-27
EVERY 250 HOURS
Air cleaner maintenance 7-28
Checking the radiator hoses 7-30
Radiator and oil cooler debris screen 7-32
Fan, Alternator, A/C Belt Wear and tension 7-33
Checking for intake rubber hose 7-35
Air-conditioner filters service 7-37
Cleaning or replacement of radiator cap 7-39
Attachment lubrication 7-40
EVERY 500 HOURS
Replacing engine oil 7-44
Replacing the Pre-Filter 7-46
Replacing the fuel filter 7-48
Bleeding the fuel system 7-49
Filter Replacement of Electromagnetic Pump 7-49
Cleaning fuel tank cap and strainer 7-51
Greasing the slewing ring 7-51
Checking slewing ring fitting bolts for loosening 7-52
Lubricating push rod of control lever with grease 7-52
Checking the air-conditioner refrigerant 7-53
EVERY 1000 HOURS (12 MONTHS)
Checking engine mounting bracket for tightening 7-55
Swing reduction lubrication 7-56
Replacing return filters 7-57
Replacement of air breather element 7-59
Checking voltage 7-60
EVERY 2000 HOURS
Changing engine coolant 7-61
Cleaning suction strainer 7-63
Cleaning of pilot line filter 7-65
Changing oil in swing reduction unit 7-66
Checking grease in slewing ring grease bath 7-67
Change oil in travel motor reduction units 7-68
EVERY 5000 HOURS
Change hydraulic oil 7-69
WHEN REQUIRED
Checking and replacing wiper blade 7-71
Wind washer fluid reservoir 7-71
Replacement of bucket 7-72
Check for abrasion/damages on tooth point and side cutter 7-73
Reversing backhoe bucket 7-75
Adjusting bucket mount gap 7-76
Fuses and relay box 7-77
Fusible link (for starter) 7-79
Fluids and lubricants 7-80
STORAGE
Machine storage 7-81
Care during storage 7-82
Storage up after 7-82
8 SPECIFICATIONS
General specifications 8-1
Dimensions and weights 8-2
Shoe types 8-4
Working ranges 8-5
Bucket and arm combinations 8-10
9 ACCESSORIES
Operation of hydraulic breaker and nibbler (for 1 pedal type) 9-1
Proportional hand control (extra, nibbler and breaker) 9-16
Objects handling 9-22
Use of bio-degradable oils 9-28
10 FORMS AND DECLARATIONS
EC Declaration of Conformity 10-1

Need help? Contact: [email protected]

https://vimeo.com/730972189

PLEASE NOTE:

• This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
• Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.

S.V