Case IH Tractor FARMALL 110A,120A,130A,140A Tier 4B Operator’s Manual – PDF DOWNLOAD

Description

Case IH Tractor FARMALL 110A,120A,130A,140A Tier 4B Operator’s Manual

CASE IH TRACTOR FARMALL 110A,120A,130A,140A TIER 4B OPERATOR’S MANUAL – PDF DOWNLOAD:

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

This manual contains information concerning the adjustment and maintenance of your new equipment. You have purchased a dependable machine, but only by proper care and operation can you expect to receive the performance and long service built into this equipment. Please have all operators read this manual carefully and keep it available for ready reference. Your CASE IH dealer will instruct you in the general operation of your new equipment; see “Delivery report – Owner copy” (11-1).

• Your dealer’s staff of factory-trained service technicians will be glad to answer any questions that may arise regarding the operation of your machine. Case IH Max Service is also available. Go to . Your CASE IH dealer carries a complete line of genuine CASE IH service parts.
• These parts are manufactured and carefully inspected to insure high quality and accurate fitting of any necessary replacement parts. Be prepared to give your dealer the model and product identification number of your new equipment when ordering parts.
• Locate these numbers now and record them below. For information on the location of the model and Product Identification Number (PIN) of your machine, see “Product identification”

TABLE OF CONTENTS:

Case IH Tractor FARMALL 110A,120A,130A,140A Tier 4B Operator’s Manual

1 GENERAL INFORMATION
Note to the owner 1-1
Intended use1-2
Electro-Magnetic Compatibility (EMC)1-3
Product identification1-4
Product Identification Number (PIN)1-8
Operator’s manual storage on the machine 1-9
Machine orientation1-10
Machine components1-12
Selective Catalytic Reduction (SCR) exhaust treatment – Product overview1-14
2 SAFETY INFORMATION
Safety rules and signal word definitions 2-1
Safety rules2-2
Ecology and the environment2-12
Safety signs2-13
Informational decals2-36
3 CONTROLS AND INSTRUMENTS
Access to operator’s platform
Proper entry and exit3-1
Operator’s seat
Mechanical operator’s seat3-3
Pneumatic operator’s seat3-4
Seat belt operation3-6
Instructional seat
Overview3-7
Forward controls
Front console3-8
Foot pedals 3-10
Selective Catalytic Reduction (SCR) exhaust treatment – Overview 3-11
Left-hand side controls
Power Take-Off (PTO) (without cab) 3-20
Parking brake3-20
Door and window operation3-21
Storage 3-21
Right-hand side controls
Transmission controls3-22
Hi / Lo Transmission 3-23
Power Take-Off (PTO) (with cab)3-23
Hydraulic controls3-24
Right-hand post3-26
Heating, Ventilation, and Air Conditioning (HVAC) controls3-27
Door and window operation3-29
Rearward controls
Rear window operation 3-30
Rear window wiper 3-30
Overhead controls
Radio 3-31
Radio operation3-31
Dome light3-39
Roof hatch3-39
Display
Analog/Digital Instrument Cluster (ADIC)3-40
Warning and status indicators3-41
Display overview 3-43
Alarms3-43
Setup menu3-52
Overview 3-52
Maintenance intervals3-53
Audible alarm buzzer 3-54
Fuel consumption units 3-55
Active error codes and warnings 3-56
Backlighting and dimming3-57
Lamps and gauges 3-57
Display 3-58
4 OPERATING INSTRUCTIONS
Commissioning the unit
Run-in period of a new machine4-1
Roll Over Protective Structure (ROPS) 4-2
Starting the unit
Starting the engine4-4
Engine starting aids 4-7
Stopping the unit
Stopping the tractor 4-9
Hydraulic trailer brakes 4-11
Moving the unit
General transmission operation4-12
Steering control4-13
5 TRANSPORT OPERATIONS
Road transport
Basic instructions5-1
High visibility position markers5-2
Recovery transport
Towing the tractor 5-7
6 WORKING OPERATIONS
Tires and wheels
Tire load and inflation charts6-1
Tractor ballasting6-7
Liquid ballast6-9
Front wheel tread settings6-11
Rear wheel tread settings6-15
Bar axle adjustment6-17
Dual rear wheels 6-22
Driveline
Creeper gears6-24
Four-Wheel Drive (4WD) 6-27
Differential lock 6-28
Front axle oscillation 6-29
Hydraulic system
Hydraulic Power Lift (HPL) 6-31
Bosch remote valves 6-34
Hydraulic remote control valves6-34
Connecting remote cylinders 6-37
Bleeding remote cylinders6-39
Operating single-acting hydraulic cylinders6-40
Operating double-acting hydraulic cylinders 6-41
Operating continuous flow hydraulic equipment 6-42
Sohipren remote valves6-44
Hydraulic remote control valves6-44
Connecting remote cylinders 6-46
Operating single-acting hydraulic cylinders6-48
Operating double-acting hydraulic cylinders 6-49
Implements
Adjusting the drawbar6-50
Hitch operation 6-53
Power Take-Off (PTO) operation 6-58
7 MAINTENANCE
General information
Safety rules – Machine service access 7-1
Warranty notice7-1
Jacking points 7-1
Opening the hood 7-2
Fueling the machine 7-3
Selective Catalytic Reduction (SCR) exhaust treatment – Basic instructions 7-4
General specification – Biodiesel fuels7-5
General specification – Diesel fuel7-7
Torque – Minimum tightening torques for normal assembly 7-8
Standard torque data for hydraulics7-13
Organic Acid Technology (OAT) coolant 7-17
Fluid capacities and lubricants 7-18
Engine oil – Recommended engine oil for operating temperature ranges 7-20
Maintenance planning
Maintenance chart 7-21
Warning light on
Engine air filter (outer element) – Clean7-23
Fuel filter water separator – Drain fluid 7-25
Brake fluid – Level make up7-26
Every 10 hours or daily
Engine oil – Level make up 7-27
Radiator, oil cooler, and condenser – Clean7-28
Engine cooling system – Level make up 7-31
Every 50 hours
Tire pressure – Check7-32
Transmission, rear axle, and hydraulic system oil – Level make up7-32
Brake fluid – Level make up7-33
Windshield washer fluid – Level make up7-33
Fuel filter water separator – Drain fluid 7-33
Cab recirculation air filter – Clean7-34
Cab air filter – Clean7-36
Wheel hardware – Check 7-37
Grease points – Grease7-38
Clutch pedal – Adjust 7-40
Every 300 hours
Four-Wheel Drive (4WD) front axle differential oil – Level make up7-42
Four-Wheel Drive (4WD) front axle hub oil – Level make up 7-42
Transmission and hydraulic oil filter – Replace 7-42
Cab and safety frame mounting hardware torque – Check 7-43
Parking brake – Adjust7-44
Brake pedal – Adjust7-46
Alternator drive belt – Check 7-46
Air conditioning compressor belt – Check7-47
Battery cables – Check 7-47
Every 600 hours
Diesel Exhaust Fluid (DEF)/AdBlue® supply module pre-filter – Clean7-48
Engine oil – Change fluid 7-52
Engine air filter (outer element) – Replace 7-54
Fuel filter water separator – Replace 7-54
Every 1200 hours or annually
Diesel Exhaust Fluid (DEF)/AdBlue® supply module pre-filter – Replace7-55
Transmission, rear axle, and hydraulic system oil – Change fluid7-59
Four-Wheel Drive (4WD) front axle differential oil – Change fluid7-60
Four-Wheel Drive (4WD) front axle hub oil – Change fluid 7-60
Every 3600 hours or two years
Diesel Exhaust Fluid (DEF)/AdBlue® supply module main filter – Replace7-61
Every 4000 hours or four years
Engine coolant – Change fluid7-65
As required
Diesel Exhaust Fluid (DEF)/AdBlue® supply module inlet filter – Replace 7-68
Diesel Exhaust Fluid (DEF)/AdBlue® tank inlet filter – Replace7-69
Diesel Exhaust Fluid (DEF)/AdBlue® supply module backflow filter – Replace7-70
Headlights – Adjust 7-71
Headlight bulb – Replace 7-71
Work light bulb – Replace7-71
Rear light bulb – Replace 7-73
Steering stops – Adjust 7-74
Steering toe-in – Adjust 7-74
Roof hatch – Cleaning7-77
Parking brake – Adjust7-78
Fuse and relay locations
Chassis fuse box 7-81
Engine fuse box7-86
Other fuses and relays 7-87
Storage
Preparing for storage 7-88
Removing from storage7-88
8 TROUBLESHOOTING
Symptom(s)
Engine 8-1
Transmission8-2
Electrical system8-2
Hydraulic system8-3
Hydraulic remote control valves 8-3
Three-point hitch8-4
Brakes 8-4
Cab8-4
9 SPECIFICATIONS
Length and height 9-1
Width9-2
Ground clearance 9-3
Weight 9-4
Engine 9-7
Cooling system9-7
Transmission9-8
Ground speeds9-9
Maximum side slope operation 9-18
Power Take-Off (PTO)9-18
Hydraulic system 9-20
Three-point linkage 9-20
Brake system 9-20
Steering system9-21
Electrical system 9-22
Lubrication system – Capacities9-23
10 ACCESSORIES
Engine10-1
Chassis 10-2
Cab 10-4
Roll Over Protective Structure (ROPS)10-6
Safety10-7
Hydraulics10-8
Hitch 10-10
11 FORMS AND DECLARATIONS
Delivery report – Owner copy 11-1
Delivery report – Dealer copy 11-2H

FILE DETAILS:

Case IH Tractor FARMALL 110A,120A,130A,140A Tier 4B Operator’s Manual_51490496
Size : 36.1 MB
Format : PDF
Language : English
Number of Pages : 356 pages
Brand: Case IH
Type of machine: Tractor
Type of document: Operator’s Manual
Model: FARMALL 110A,120A,130A,140A Tier 4B
Part No: 51490496

PLEASE NOTE:

• This is the SAME MANUAL used by the dealerships to diagnose your vehicle
• No waiting for couriers / posts as this is a PDF manual and you can download it within 2 minutes time once you make the payment.
• Your payment is all safe and the delivery of the manual is INSTANT – You will be taken to the DOWNLOAD PAGE.
• So have no hesitations whatsoever and write to us about any queries you may have : heydownloadss @gmail.com