Cat Rotary Track Drill SD250 Hydra-Track Self Contained Hydraulic track Drill Operator & Maintenance Manual – PDF DOWNLOAD

Description

Cat Rotary Track Drill SD250 Hydra-Track Self Contained Hydraulic track Drill Operator & Maintenance Manual – PDF DOWNLOAD

DESCRIPTION:

Cat Rotary Track Drill SD250 Hydra-Track Self Contained Hydraulic track Drill Operator & Maintenance Manual – PDF DOWNLOAD

Maintenance

• Two People shall be present when performing service work, both being fully trained on the safety issues. One person shall supervise from the operator’s position and have immediate access to an emergency stop in all situations. Visual, audible or verbal communication signals must be established and understood by both persons.

• Do Not service or perform maintenance while machine is running.

• Do Not hammer bit or drill steel. Use only proper tools to make repair or adjustments. • Do Not weld or grind near oil lines.

• Do Not attempt to remove radiator cap when engine is hot or has overheated.

• Do Not smoke or use an open flame near batteries, or fuel system. When servicing the batteries. Batteries can give off hydrogen which is a highly explosive gas. ——·–~

• Do Not direct high pressure cleaning agents or water on electrical connections

• Do maintain a metal-to-metal contact between the fill nozzle and fuel tank when filling the fuel tank. This will prevent sparks and the possibility of an explosion.

• Do be sure each person is adequately trained to perform service and maintenance procedures.

• Do place a warning tag on starting controls to alert personnel that someone is working on the machine and disconnect battery before making repairs or adjustments to machine.

• Do be sure you have adequate lighting when performing service work at night.

• Do relieve pressure on hydraulic or pneumatic systems before loosening connections or parts.

• Do be sure machine and components are well supported before servicing or replacing parts.

• Do be sure no tools or other loose objects are left on the engine or drive mechanisms. They could be thrown by this equipment with a powerful force.

TABLE OF CONTENTS:

Cat Rotary Track Drill SD250 Hydra-Track Self Contained Hydraulic track Drill Operator & Maintenance Manual – PDF DOWNLOAD

INTRODUCTION
Ordering Information ii
Glossary of Terms v
SAFETY SECTION 1
Overview of Potential Hazards 1-2
Safety Instructions 1-3
Before Operation 1-3
Operation 1-3
After Operation 1-3
Maintenance 1-4
Equipment Transfer 1-4
GENERAL DESCRIPTION SECTION 2
General Description 2-2
Component Location – Cab Machine 2-2 & 2-3
Component Location – Non-Cab Machine 2-4 & 2-5
Standard Features 2-6
OPERATOR CONTROLS SECTION 3 ·: 3- 2
1~ Trammmg & Pos1t1omng Controls (non-cab machine) 3-4
Component Locations • 3-12
Instrument Panels 3-13
Overhead Console 3-14
Right Side Console 3-16
Joystick – Drill/f ram Controls 3-18
Additional Controls 3-20
Vertical Indicator 3-22
START-UP, SHUTDOWN, TRAMMING AND TOWING SECTION 4
Pre-Start Checklist 4-2
Engine, Gearcases and Hydraulic Fluid Types 4-2
Air Compressor 4-2
Feed and Drill 4-3
Fuel Requirements 4-3
Start-up Procedure (non-cab machine) 4-4
Shutdown Procedure (non-cab machine) 4-6
Tramming Procedure (non-cab machine) 4-8
Start-up Procedure (cab machine) 4-10
Shutdown Procedure (cab machine) 4-12
Tramming Procedure (cab machine) : 4-14
Introduction iii
BI615908 Table of Contents
Towing Procedure 4-16
Gear Drive Disconnect 4-16
Drill Positioning Procedure (non-cab machine) 5-4
Collaring the Hole (non-cab machine) 5-5 : l
Manual Drilling (non-cab machine) 5-7
Auxiliary Air Option 5-8
Smart Drill Feature (non-cab machine) 5-9 : ]
Adding Drill Rod (manual rod rack) 5-11
Removing Drill Rod (manual rod rack) 5-12 ,
Linear Rod Changer (cab machine) 5-14
Loading Drill Rod 5-15
Collaring the Hole (cab machine) 5-19 ‘,· ]
Manual Drilling (cab machine) 5-21
Smart Drill Feature (cab machine) 5-23
Adding Drill Rod (linear rod changer) 5-25 •, )
Removing Drill Rod (linear rod changer) 5-31
HPRlH Drill Shank Replacement 5-34
HPR45 D ·11 Sh k R I t 5 36 ___ r__ _”_
PREVENTIVE MAINTENANCE SECTION 6
Hydraulic Oils for Percussion Drills 6-2
Lubrication and Inspection 6-3
Bolt Torque Specifications 6-4
Maintenance Schedule 6-5
Hydraulic Oil Specifications 6-6
Daily Operational Checklist 6-7
Engine Oil and Filter – Change 6-8
Engine Fuel Filter – Change 6-9
Fuel;Water Separator 6-9
Engine Air Cleaner Filter 6-10
Compressor Air Cleaner Filter 6-11
Compressor Oil Filter 6-12
Compressor Oil Check/Change 6-13
Compressor Oil Separator Element 6-14
Detergent System (Optional) 6-16
Servicing the “Y” Strainer 6-17
618~- 1 Hydraulic Return Filter 6-19 )
Hydraulic Pre-Charge Filter 6-20 —,’ j
C()_()lant System (5 21
Track Tension Adjustment 6-23
iv Introduction :

CAT ROTARY TRACK DRILL SD250 HYDRA-TRACK SELF CONTAINED HYDRAULIC TRACK DRILL OPERATOR & MAINTENANCE MANUAL – PDF DOWNLOAD:

IMAGES PREVIEW OF THE MANUAL:

PLEASE NOTE:

• This is not a physical manual but a digital manual – meaning no physical copy will be couriered to you. The manual can be yours in the next 2 mins as once you make the payment, you will be directed to the download page IMMEDIATELY.
• This is the same manual used by the dealers inorder to diagnose your vehicle of its faults.
• Require some other service manual or have any queries: please WRITE to us at [email protected]

S.M