Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

Description

Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

8YS1-Up (Engine)
9NS1-Up (Engine)

Important Safety Information :

Most accidents that involve product operation, maintenance and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills and tools to perform these functions properly.

• Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result in injury or death. Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and understood the operation, lubrication, maintenance and repair information.
• Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.
• The hazards are identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “DANGER”, “WARNING” or “CAUTION”. The Safety Alert “WARNING” label is shown below.

TABLE OF CONTENTS:

Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

Disassembly andAssembl y Section
Summary of Revisions 5
Fuel Priming Pump – Remove and Install 5
Fuel Filter Base – Remove and Install 6
Fuel Transfer Pump – Remove 7
Fuel Transfer Pump – Install 8
Fuel Manifold – Remove 8
Fuel Manifold – Install 9
Electronic Unit Injector – Remove 10
Electronic Unit Injector – Install 11
Electronic Unit Injector Sleeve – Remove 12
Electronic Unit Injector Sleeve – Install 13
Turbocharger – Remove 14
Turbocharger – Install 15
Exhaust Manifold – Remove and Install 15
Inlet Manifold – Remove 16
Inlet Manifold – Install 16
Inlet and Exhaust Valve Springs – Remove and
Install 17
Inlet and Exhaust Valves – Remove and Install 19
Inlet and Exhaust Valve Guides – Remove and
Install 20
Inlet and Exhaust Valve Seat Inserts – Remove and
Install 21
Engine Centrifugal Oil Filter – Remove and
Install 23
Engine Oil Filter Base – Remove 25
Engine Oil Filter Base – Disassemble 26
Engine Oil Filter Base – Assemble 27
Engine Oil Filter Base – Install 29
Engine Oil Cooler – Remove 29
Engine Oil Cooler – Install 31
Engine Oil Pump – Remove 31
Engine Oil Pump – Disassemble 32
Engine Oil Pump – Assemble 33
Engine Oil Pump – Install 34
Water Pump – Remove 34
Water Pump – Disassemble 36
Water Pump – Assemble 38
Water Pump – Install 41
Water Temperature Regulator – Remove and Install
Water Outlet Manifold – Remove 44
Water Outlet Manifold – Install 45
Flywheel – Remove 46
Flywheel – Install 46
Crankshaft Rear Seal – Remove 47
Crankshaft Rear Seal – Install 47
Crankshaft Rear Seal Carrier – Remove and
Install 48
Flywheel Housing – Remove and Install 49
Rear Power Take-Off (RPTO) – Remove 50
Rear Power Take-Off (RPTO) – Install 53
Vibration Damper and Pulley – Remove and Install
Crankshaft Front Seal – Remove 57
Crankshaft Front Seal – Install 57
Front Cover – Remove 57
Front Cover – Install 58
Gear Group (Front) – Remove 59
Gear Group (Front) – Install 60
Housing (Front) – Remove 61
Housing (Front) – Install 62
Accessory Drive – Remove 64
Accessory Drive – Disassemble 65
Accessory Drive – Assemble 66
Accessory Drive – Install 66
Valve Mechanism Cover – Remove and Install 67
Valve Mechanism Cover Base – Remove and
Install 68
Compression Brake – Remove 69
Compression Brake – Disassemble 69
Compression Brake – Assemble 73
Compression Brake – Install 76
Rocker Shaft and Pushrod – Remove 77
Rocker Shaft – Disassemble 78
Rocker Shaft – Assemble 78
Rocker Shaft and Pushrod – Install 79
Cylinder Head – Remove 80
Cylinder Head – Install 82
Lifter Group – Remove and Install 85
Camshaft – Remove 87
Camshaft – Install 88
Camshaft Gear – Remove and Install 89
Camshaft Bearings – Remove 90
Camshaft Bearings – Install 90
Engine Oil Pan – Remove and Install 91
Cylinder Liner – Remove 93
Cylinder Liner – Install 94
Piston Cooling Jets – Remove and Install 95
Pistons and Connecting Rods – Remove 96
Pistons and Connecting Rods – Disassemble 97
Pistons and Connecting Rods – Assemble 98
Pistons and Connecting Rods – Install 99
Connecting Rod Bearings – Remove 100
Connecting Rod Bearings – Install 101
Crankshaft Main Bearings – Remove 102
Crankshaft Main Bearings – Install 103
Crankshaft – Remove 104
Crankshaft – Install 105
Crankshaft Gear – Remove and Install 106
Bearing Clearance – Check 107
Camshaft Position Sensor – Remove and Install 108
Crankshaft Position Sensor – Remove and
Install 109
Coolant Temperature Sensor – Remove and
Install 110
Engine Oil Pressure Sensor – Remove and Install
111
Belt Tensioner – Remove and Install 112
Engine Control Module – Remove and Install 113
Alternator – Remove and Install 114
Electric Starting Motor – Remove and Install 115
Air Conditioner Support Bracket – Remove and
Install 116
Air Compressor – Remove and Install 117
Air Compressor Drive Gear – Remove 118
Air Compressor Drive Gear – Install 119
Index Section
Index 120

CATERPILLAR C-10 & C-12 TRUCK ENGINES DISASSEMBLY & ASSEMBLY MANUAL – PDF DOWNLOAD:

PLEASE NOTE:

• This is the same manual used by the dealers to diagnose and troubleshoot your vehicle
• You will be directed to the download page as soon as the purchase is completed. The whole payment and downloading process will take anywhere between 2-5 minutes
• Need any other service / repair / parts manual, please feel free to contact [email protected] . We still have 50,000 manuals unlisted

S.V