Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual

Description

Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

MBJ1-Up (Engine)
MBL1-Up (Engine)

Important Safety Information :

Most accidents that involve product operation, maintenance and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills and tools to perform these functions properly.

• Improper operation, lubrication, maintenance or repair of this product can be dangerous and could result in injury or death. Do not operate or perform any lubrication, maintenance or repair on this product, until you have read and understood the operation, lubrication, maintenance and repair information.
• Safety precautions and warnings are provided in this manual and on the product. If these hazard warnings are not heeded, bodily injury or death could occur to you or to other persons.
• The hazards are identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “DANGER”, “WARNING” or “CAUTION”. The Safety Alert “WARNING” label is shown below.

TABLE OF CONTENTS:

Caterpillar C-10 & C-12 Truck Engines Disassembly & Assembly Manual – PDF DOWNLOAD

Disassembly andAssembl y Section
Fuel Priming Pump – Remove and Install 5
Fuel Filter Base – Remove and Install 5
Fuel Recirculation Valve – Remove and Install 7
Fuel Transfer Pump – Remove 8
Fuel Transfer Pump – Install 8
Fuel Manifold – Remove 8
Fuel Manifold – Install 9
Electronic Unit Injector – Remove 10
Electronic Unit Injector – Install 11
Electronic Unit Injector Sleeve – Remove 12
Electronic Unit Injector Sleeve – Install 13
Turbocharger – Remove 14
Turbocharger – Install 15
Modulating Valve – Remove and Install 16
Exhaust Manifold – Remove and Install 17
Inlet Manifold – Remove 18
Inlet Manifold – Install 18
Inlet and Exhaust Valve Springs – Remove and
Install 19
Inlet and Exhaust Valves – Remove and Install 21
Inlet and Exhaust Valve Guides – Remove and
Install 22
Inlet and Exhaust Valve Seat Inserts – Remove and
Install 23
Engine Centrifugal Oil Filter – Remove and
Install 24
Engine Oil Filter Base – Remove 27
Engine Oil Filter Base – Disassemble 28
Engine Oil Filter Base – Assemble 29
Engine Oil Filter Base – Install 30
Engine Oil Cooler – Remove 31
Engine Oil Cooler – Install 32
Engine Oil Pump – Remove 33
Engine Oil Pump – Disassemble 34
Engine Oil Pump – Assemble 35
Engine Oil Pump – Install 35
Water Pump – Remove 36
Water Pump – Disassemble 37
Water Pump – Assemble 40
Water Pump – Install 42
Water Temperature Regulator – Remove and Install
Water Outlet Manifold – Remove 46
Water Outlet Manifold – Install 47
Flywheel – Remove 47
Flywheel – Install 48
Crankshaft Rear Seal – Remove 48
Crankshaft Rear Seal – Install 49
Crankshaft Rear Seal Carrier – Remove and
Install 50
Flywheel Housing – Remove and Install 51
Rear Power Take-Off (RPTO) – Remove 52
Rear Power Take-Off (RPTO) – Install 54
Vibration Damper and Pulley – Remove and Install
Crankshaft Front Seal – Remove 58
Crankshaft Front Seal – Install 58
Front Cover – Remove 59
Front Cover – Install 60
Gear Group (Front) – Remove 60
Gear Group (Front) – Install 61
Housing (Front) – Remove 63
Housing (Front) – Install 63
Housing (Front) – Install 64
Accessory Drive – Remove 66
Accessory Drive – Disassemble 67
Accessory Drive – Assemble 68
Accessory Drive – Install 68
Valve Mechanism Cover – Remove and Install 69
Valve Mechanism Cover Base – Remove and
Install 70
Compression Brake – Remove 71
Compression Brake – Disassemble 71
Compression Brake – Assemble 75
Compression Brake – Install 78
Rocker Shaft and Pushrod – Remove 79
Rocker Shaft and Pushrod – Install 80
Cylinder Head – Remove 80
Cylinder Head – Install 83
Lifter Group – Remove and Install 86
Camshaft – Remove 88
Camshaft – Install 89
Camshaft Gear – Remove and Install 90
Camshaft Bearings – Remove 90
Camshaft Bearings – Install 91
Engine Oil Pan – Remove and Install 92
Cylinder Liner – Remove 94
Cylinder Liner – Install 95
Piston Cooling Jets – Remove and Install 96
Pistons and Connecting Rods – Remove 97
Pistons and Connecting Rods – Disassemble 98
Pistons and Connecting Rods – Assemble 99
Pistons and Connecting Rods – Install 100
Connecting Rod Bearings – Remove 101
Connecting Rod Bearings – Install 102
Crankshaft Main Bearings – Remove 103
Crankshaft Main Bearings – Install 104
Crankshaft – Remove 105
Crankshaft – Install 106
Crankshaft Gear – Remove and Install 107
Bearing Clearance – Check 108
Camshaft Position Sensor – Remove and Install 109
Crankshaft Position Sensor – Remove and
Install 110
Coolant Temperature Sensor – Remove and
Install 111
Engine Oil Pressure Sensor – Remove and Install
Fuel Pressure Sensor – Remove and Install 113
Boost Pressure Sensor – Remove and Install 113
Belt Tensioner – Remove and Install 114
Engine Control Module – Remove and Install 115
Alternator – Remove and Install 116
Electric Starting Motor – Remove and Install 116
Air Conditioner Support Bracket – Remove and
Install 117
Air Compressor – Remove and Install 118
Air Compressor Drive Gear – Remove 120
Air Compressor Drive Gear – Install 120
Index Section
Index 122

CATERPILLAR C-10 & C-12 TRUCK ENGINES DISASSEMBLY & ASSEMBLY MANUAL:

PLEASE NOTE:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

S.V