Fendt NA Harvesting 9490 X 9490 X AL WORKSHOP SERVICE MANUAL – PDF DOWNLOAD

Description

Fendt NA Harvesting 9490 X 9490 X AL WORKSHOP SERVICE MANUAL – PDF DOWNLOAD

DESCRIPTION:

Fendt NA Harvesting 9490 X 9490 X AL WORKSHOP SERVICE MANUAL – PDF DOWNLOAD

1.1 Using the manual
1.1.1 Using the manual
General

All operations described in this manual relating to repairs and maintenance must only be carried out by trained service personnel. The purpose of the manual is to help dealers and workshops start up, service and repair AGCO’s equipment as efficiently and effectively as possible. If the specified procedures are followed and the recommended special tools used where necessary, jobs can be completed within the time indicated in the “Repair Time Schedule” manual.

Pagination
Example: see §3. 7 .3, page 89
This manual is divided into chapters and sections. In the example the figures show:
First figure = Chapter
Second figure = Section
Third figure = Consecutive number in the section in question
69 = Page number in manual
The publication number and version appear at the bottom of the pageUse
To make it easier to look things up, there is a table of contents at the beginning of every chapter listing the
various sections in the chapter.
Modifications
Modified pages have the same section numbering as their predecessors: Only the page number and version
number change.
The old pages must be destroyed.
Service tools
In the case of jobs that require service tools, the number of the tool is specified at the point in the text where
it is needed.
Repairs and replacing parts
When replacing parts, it is very important to only ever use genuine AGCO spares.
Please pay particular attention to the following points when it comes to repairs and fitting spare parts or other
equipment.
Fitting non-genuine spare parts may impair the safety of the machine.
In some countries it is against the law to fit parts that do not conform to the manufacturer’s specifications.
Torque wrenches must always be adjusted in accordance with the instructions given in the workshop manual.
Fit locking devices where specified. If the locking device breaks when removed, fit a new one.
If non-genuine AGCO parts are fitted, the machine will no longer be covered by the right to complain, as the
manufacturer provides a warranty on all AGCO components. AGCO dealers are under the obligation to supply
genuine parts only.
Repair Time Schedule
The “Repair Time Schedule” manual contains a table of standard time requirements for the commonest repairs
on a combine. The manual’s sections follow the layout of the spare parts catalogue.

TABLE OF CONTENTS:

Fendt NA Harvesting 9490 X 9490 X AL WORKSHOP SERVICE MANUAL – PDF DOWNLOAD

1 Introduction – Specifications 13
1 1 Using the manual 15
1 1 1 Using the manual 15
1 2 General specifications 16
1 2 1 Dimensions and specifications 16
1 2 2 Specification table for tyres with equipment 25
1 3 Safety precautions 28
1 3 1 Safety precautions 28
1 3 2 Safety in the workshop 28
1 3 3 Safety – a word to the mechanic 28
1 3 4 Safety – danger, warning and caution 28
1 3 5 Safety decals 29
1 3 6 General 29
1 3 7 Personal safety 29
1 3 8 Considerations with regard to equipment 30
1 3 9 General considerations 31
1 3 10 Operational considerations 31
1 3 11 Maintenance techniques 32
1 4 Practical advice 34
1 4 1 Practical advice 34
1 5 Start-up instructions 38
1 5 1 General 38
1 5 2 Pre-delivery checks 38
1 5 3 Instruction of combine operator 40
1 6 Conversion tables 43
1 6 1 Conventional units of measurement 43
1 7 Locking and sealing agents 44
1 7 1 Locking and sealing agents 44
1 8 Wheel nut torques 45
1 8 1 Wheels 45
1 8 2 Bolts with metric threads 45
1 8 3 Nuts with metric threads 46
2 Cutting table 47
2 1 General 49
2 1 1 Table, general 49
2 2 Knife drive – wobble box 18-30 ft 50
2 2 1 Removal 50
2 2 2 Assembly 50
2 2 3 Reconditioning the wobble box 51
2 2 4 Positioning the double fingers, knife and crop lifters 57
2 3 Table auger, 18-30 ft 58
2 3 1 Removal 58
2 3 2 Assembly 59
2 3 3 Replacing the shaft on the left-hand side 59
2 3 4 Replacing the shaft on the right-hand side 59
2 3 5 Replacing the crankshaft 60
2 3 6 Replacing the feathering fingers, bearings and bushes 61
2 3 7 Adjusting the table auger and feathering fingers 62
2 4 Table body, 18-30 ft 64
2 4 1 Adjusting the cut-off strips 64
2 4 2 Adjusting and positioning the ground sensor – PowerFlow 65
FENDT 9490 x – EAME 3
D3158800M2 – SIN 502000001 + SIN 502400001
Table of contents ~ -a!s! ‘ _ ,
2 5 Table body, 35 ft 67
2 5 1 Adjusting the ground sensor – 35’ PowerFlow 67
2 6 Friction clutch and chain drive 18-30 ft 69
2 6 1 Removing the friction coupling 69
2 6 2 Assembly 69
2 6 3 Replacing the bearings and sprockets 70
2 7 Countershaft, 18-30 ft 71
2 7 1 Removing the countershaft 71
2 7 2 Fitting the countershaft 72
2 8 PowerFlow belts, 18-30 ft 73
2 8 1 PowerFlow belts 73
2 8 2 Removal, belts 73
2 8 3 Assembly, belts 76
2 8 4 Replacing the front rollers and bearings, scraper adjustment 77
2 8 5 Replacing the rear rollers and bearings, scraper adjustment 79
2 8 6 Replacing and aligning the bearing housing, rear rollers 80
2 8 7 Belt tensioning and running-in 81
3 Reel 85
3 1 Reel, 18-30 ft 87
3 1 1 Removal 87
3 1 2 Assembly 88
3 1 3 Replacing the reel tine bar and plastic bearings 89
3 1 4 Replacing the guide rollers, eccentric, guide ring and bearings 90
3 1 5 Replacing the reel plates 91
3 1 6 Replacing the reel tube, bearings 91
3 2 Oil motor and chain drive, 18-30 ft 92
3 2 1 Replacing the oil motor 92
3 2 2 Replacing the flow divider 92
3 3 Hydraulic cylinders, 18-30 ft 93
3 3 1 Replacing the cylinder – reel up/down 93
3 3 2 Replacing the cylinder – reel forward/back 94
3 3 3 Reconditioning of hydraulic cylinders 94
3 4 Oil motor and chain drive, 35 ft 97
3 4 1 Replacement of oil motor, 35 ft 97
3 4 2 Replacing the flow divider 97
3 5 Hydraulic cylinders, 35 ft 98
3 5 1 Replacing the cylinder – reel forward/back 98
4 Main crop elevator 99
4 1 General 101
4 1 1 Main crop elevator, general 101
4 2 Main crop elevator 1 02
4 2 1 Removal of Crop Elevator 102
4 2 2 Fitting the crop elevator 103
4 2 3 Bearing block on machine frame 104
4 2 4 Replacing the lifting ram 104
4 2 5 Reconditioning the hydraulic cylinder 105
4 2 6 Replacing the cutting height preset sensor 106
4 3 Crop elevator chain 107
4 3 1 Crop elevator chain, general 107
4 3 2 Removing the crop elevator chain 107
4 3 3 Fitting the crop elevator chain 108
4 3 4 Replacement of slats 109
4 3 5 Replacing the slide rails in the crop elevator 109
4 3 6 Replacing the intermediate plate 110
4 4 Elevator chain top shaft 111
4 4 1 Removing the elevator chain top shaft 111
4 4 2 Fitting the elevator chain top shaft 112
4 4 3 Replacing the bearings 112
4 4 4 Replacing the sprockets and centre bearing 114
4 4 5 Replacing the shaft protection tube 117
4 FENDT 9490 x – EAME
D3158800M2- SIN 502000001 + SIN 502400001
Table of contents
4 5 Elevator chain front shaft 118
4 5 1 Removing the elevator chain front shaft 118
4 5 2 Fitting the elevator chain front shaft 119
4 5 3 Replacing the shaft bearings 120
4 6 Elevator countershaft 121
4 6 1 Removing the elevator intermediate shaft 121
4 6 2 Fitting elevator intermediate shaft 122
4 7 Friction clutch and belt drive 123
4 7 1 Removal of friction clutch 123
4 7 2 Fitting the friction clutch 123
4 7 3 Reconditioning of the friction clutch 124
4 8 Adapter 125
4 8 1 Removal of adapter 125
4 8 2 Fitting the adapter 126
4 8 3 Replacing the levelling cylinder 126
4 8 4 Reconditioning the hydraulic cylinder 126
4 8 5 Replacing the angle sensor 127
4 9 Hydraulic reversing 128
4 9 1 Removal of hydraulics motor 128
4 9 2 Removing the hydraulic cylinder 129
5 Threshing unit 131
5 1 General 133
5 1 1 Threshing unit, general 133
5 2 Stone trap 134
5 2 1 Removal 134
5 2 2 Assembly 135
5 3 Concave 136
5 3 1 Removing the concave 136
5 3 2 Fitting the concave 137
5 3 3 Adjusting the concave laterally 137
5 3 4 Concave setting – initial setting 138
5 3 5 Replacing the lead-in plate 139
5 3 6 Replacing the shaft for concave setting 139
5 4 Threshing cylinder 141
5 4 1 Removing the threshing cylinder 141
5 4 2 Fitting the treshing cylinder 142
5 4 3 Replacing the bearings 143
5 4 4 Replacing the rasp bars and backing bars 144
5 4 5 Replacing the shaft and cylinder spiders 144
5 5 Cylinder variator – table clutch 146
5 5 1 Removal, hydraulic variator 146
5 5 2 Assembly, hydraulic variator 147
5 5 3 Reconditioning the hydraulic variator pulley 147
5 5 4 Removal, mechanical variator 149
5 5 5 Assembly, mechanical variator 149
5 5 6 Reconditioning the mechanical variator pulley 150
5 5 7 Removal, hydraulic table clutch 151
5 5 8 Fitting the hydraulic table clutch 152
5 5 9 Reconditioning the hydraulic table clutch 153
5 6 Rear beater 158
5 6 1 Removing the rear beater 158
5 6 2 Fitting the rear beater 159
5 7 Rear beater concave 160
5 7 1 Removing the rear beater concave 160
5 7 2 Fitting the rear beater concave 160
5 8 Rotor Feeder 161
5 8 1 Removal, Rotor Feeder 161
5 8 2 Fitting the Rotor Feeder 162
5 8 3 Replacing the bearings 163
5 8 4 Replacing deflector and distributor plates 164
FENDT 9490 x – EAME 5
D3158800M2 – SIN 502000001 + SIN 502400001
Table of contents ~ -a!s! ‘ _ ,
5 9 Rotor Feeder concave 166
5 9 1 Removal, Rotor Feeder concave 166
5 9 2 Fitting the Rotor Feeder concave 166
6 Rotor unit 167
6 1 General 169
6 1 1 General 169
6 2 Rotor varistor 170
6 2 1 Removal, hydraulic variator 170
6 2 2 Assembly, hydraulic variator 171
6 2 3 Reconditioning the hydraulic variator pulley 172
6 2 4 Removal, mechanical variator 172
6 2 5 Assembly, mechanical variator 173
6 2 6 Reconditioning the mechanical variator pulley 173
6 2 7 Replacing and reconditioning the magnetic clutch 175
6 3 Shaft for mechanical varistor 177
6 3 1 Removal 177
6 3 2 Assembly 177
6 4 Right-angle gear 178
6 4 1 Removing the right-angle gear 178
6 4 2 Fitting the right-angle gear 179
6 5 Rotor 181
6 5 1 Removal, rotor 181
6 5 2 Fitting the rotor 182
6 5 3 Replacing the front bearing 183
6 5 4 Replacing the rear bearing 184
6 6 Rotor cage 185
6 6 1 Removal 185
6 6 2 Assembly 187
6 6 3 Replacing grate sections 187
7 Shaker shoe – Fanning mill 189
7 1 General 191
7 1 1 Shaker shoe – fanning mill, general 191
7 2 Fanning mill 192
7 2 1 Removing the fanning mill 192
7 2 2 Fitting the fanning mill 193
7 2 3 Replacing the fan blades 193
7 2 4 Replacing the fanning mill deflectors 194
7 2 5 Replacing the seals 195
7 3 Main grain pan frame 196
7 3 1 General 196
7 3 2 Removal, main grain pan frame 196
7 3 3 Fitting the main grain pan frame 197
7 3 4 Replacing the swivel arm and bearings 198
7 3 5 Replacing the seals 199
7 4 Second grain pan 200
7 4 1 Removal 200
7 4 2 Fitting the second grain pan 200
7 4 3 Replacing the swivel arm and bearings 201
7 4 4 Adjusting second grain pan 202
7 5 Top shaker shoe 204
7 5 1 Removing the top shaker shoe 204
7 5 2 Assembly 205
7 5 3 Replacing the swivel arm and bearings 206
7 5 4 Replacement of seals 207
7 5 5 Replacing and calibrating the actuator – sieves 207
7 6 Bottom shaker shoe 209
7 6 1 Removing the bottom shaker shoe 209
7 6 2 Assembly 210
7 6 3 Replacing the swivel arm and bearings 211
7 6 4 Replacing the seals 211
6 FENDT 9490 x – EAME
D3158800M2- SIN 502000001 + SIN 502400001
Table of contents
7 6 5 Electric sieve setting – initial setting 211
7 7 Bottom augers 212
7 7 1 Removing the grain auger 212
7 7 2 Fitting the grain auger 212
7 7 3 Removing the returns bottom auger 213
7 7 4 Fitting the returns bottom auger 214
7 8 Eccentric drive 21 5
7 8 1 Removing the eccentric drive 215
7 8 2 Fitting the eccentric drive 216
7 8 3 Adjusting the connecting rod/ aligning the shaker shoes 217
7 8 4 Replacing the connecting rod bearing 218
7 8 5 Replacing the bearings and eccentric shaft 219
7 9 Transmissions 220
7 9 1 Replacing and reconditioning the fanning mill variator 220
7 9 2 Adjusting the fanning mill variator 221
7 9 3 Replacing and reconditioning the counter drive 222
8 Elevators – augers 223
8 1 Tank filling elevator 225
8 1 1 Removing the tank filling elevator 225
8 1 2 Fitting the tank filling elevator 226
8 1 3 Replacing the top shaft, bearings and sprockets 227
8 1 4 Replacing the bottom sprocket 228
8 1 5 Replacing the elevator chain 229
8 2 Returns auger 230
8 2 1 Removing the returns auger 230
8 2 2 Fitting the returns auger 232
8 2 3 Replacing the top bearing 233
8 2 4 Removing and reconditioning the right-angle gear 233
8 3 De-awner 235
8 3 1 Removing the de-awner 235
8 3 2 Fitting the de-awner 235
8 4 Tank filling auger 236
8 4 1 Removing the pivotable part 236
8 4 2 Replacing the top bearing 236
8 4 3 Removing the fixed part bearing 237
8 4 4 Reconditioning the right-angle gear 238
8 5 Transmission 240
8 5 1 Replacing the countershaft and bearings 240
9 Engine 241
9 1 General 243
9 1 1 Engine, general 243
9 2 Replacing the engine 244
9 2 1 Removing the engine assembly 244
9 2 2 Fitting the engine assembly 247
10 Unloading auger – Grain tank 249
10 1 Moisture sensor 251
10 1 1 Removing the moisture sensor 251
11 Drive unit 253
11 1 Radiator – intercooler 255
11 1 1 Removal, combined radiator 255
11 1 2 Fitting, combined radiator 256
11 2 Hydraulic oil cooler 258
11 2 1 Removing the oil cooler 258
11 2 2 Fitting the oil cooler 258
11 3 Fuel cooler 259
11 3 1 Removing the fuel cooler 259
11 3 2 Fitting the fuel cooler 259
FENDT 9490 x – EAME 7
D3158800M2 – SIN 502000001 + SIN 502400001
Table of contents ~ -a!s! ‘ _ ,
11 4 Condenser – air conditioning 260
11 4 1 Removing the condenser 260
11 4 2 Fitting the condenser 260
11 5 Rotary screen 261
11 5 1 Removing the rotary screen 261
11 5 2 Fitting the rotary screen 262
11 5 3 Adjusting the radiator cleaning plate 263
11 5 4 Reconditioning the countershaft drive 264
11 6 Dust aspirator 265
11 6 1 Removing the dust aspirator 265
11 6 2 Fitting the dust aspirator 265
11 6 3 Reconditioning the dust aspirator 266
11 7 Hydrostatic pump 267
11 7 1 Removing the hydrostatic pump 267
11 7 2 Fitting the hydrostatic pump 268
11 8 Auxiliary hydraulic pump 269
11 8 1 Removing the hydraulic pump 269
11 8 2 Fitting the hydraulic pump 269
11 9 Hydraulic oil tank 270
11 9 1 Removing the hydraulic oil tank 270
11 9 2 Fitting the hydraulic oil tank 270
11 10 Fuel tank 271
11 10 1 Removing the fuel tank 271
11 10 2 Fitting the fuel tank 272
11 10 3 Tank gauge 272
11 11 SCR system 273
11 11 1 Removing the DEF tank 273
11 11 2 Fitting the DEF tank 273
11 11 3 Removing the DEF catalytic converter 274
11 11 4 Fitting the DEF catalytic converter 275
11 11 5 Supply module 275
11 11 6 Dosing module 276
11 11 7 Tank sensor, DEF 276
11 12 Compressor – air conditioning 277
11 12 1 Removing the A/C compressor 277
11 12 2 Fitting the A/C compressor 277
11 13 Power take-off 278
11 13 1 Removing the power take-off 278
11 13 2 Fitting the power take-off 280
11 13 3 Replacing the clutch 280
11 13 4 Replacing the output shaft/bearings 281
12 Transmissions 283
12 1 General 285
12 1 1 Transmissions, General 285
12 2 Countershaft 286
12 2 1 Removing the countershaft 286
12 2 2 Fitting the countershaft 288
12 2 3 Replacing the bearings 288
12 3 Replacing the belts, right-hand side 289
12 3 1 Cutting table countershaft – knife drive, right side 35 ft 289
12 3 2 Elevator countershaft – hydraulic engine, reversing 289
12 3 3 Rear beater – counter drive, cylinder variator 290
12 3 4 Counter drive, variator – threshing cylinder 291
12 3 5 Rear beater – Rotor Feeder 292
12 3 6 Rear beater – fanning mill variator 293
12 3 7 Fanning mill variator – fanning mill 294
12 3 8 Countershaft – dust aspirator, rotary screen counter drive 294
12 3 9 Countershaft – countershaft 295
12 3 10 Countershaft – tank filling elevator, tank filling auger 295
12 3 11 Countershaft – returns augers 296
12 3 12 Rotary screen counter drive – rotary screen 297
8 FENDT 9490 x – EAME
D3158800M2- SIN 502000001 + SIN 502400001
~~ni T Table of contents
12 3 13 Rotor countershaft – right-angle gear 297
12 4 Replacing the chains, right-hand side 298
12 4 1 Reel drive 298
12 4 2 Reel drive, 35 ft 299
12 5 Replacing the belts, left-hand side 300
12 5 1 Table countershaft – knife drive 300
12 5 2 Cutting table countershaft – knife drive, left side 35 ft 300
12 5 3 PTO shaft – table countershaft 301
12 5 4 Counter pulley – elevator countershaft 301
12 5 5 Rear beater – elevator chain top shaft – idler gear 302
12 5 6 Countershaft – rear beater 303
12 5 7 Engine – countershaft 304
12 5 8 Engine – unloading auger counter drive 1 306
12 5 9 Unloading auger counter drive 1 – unloading auger counter drive 2 309
12 5 10 Countershaft – counter drive, straw chopper 310
12 5 11 Counter drive, straw chopper – straw chopper 310
12 5 12 Rear beater – countershaft, shaker shoe drive 311
12 5 13 Countershaft, shaker shoe drive – eccentric shaft 311
12 5 14 Countershaft- hydraulic pump, chaff spreader 312
12 5 15 Engine – rotor countershaft 312
12 5 16 Rotor countershaft- hydraulic pump, Maxi Spreader 313
12 5 17 Engine – hydrostatic pump 314
12 6 Replacing the chains, left-hand side 315
12 6 1 Table countershaft – table auger 315
12 6 2 Cutting table countershaft – table auger, 35 ft 315
12 6 3 Table auger – belt rollers (PowerFlow) 316
12 6 4 Table auger – belt rollers, 35 ft 316
12 6 5 Unloading auger counter drive 2 – bottom auger 317
13 Undercarriage 319
13 1 Auto Level final drive bracket 321
13 1 1 Removal 321
13 1 2 Assembly 322
13 1 3 Replacing the bushing 324
13 1 4 Replacing the hydraulic cylinder 325
13 1 5 Reconditioning of hydraulic cylinder 325
13 1 6 Adjusting the Auto Level potentiometer 326
13 2 Final drives 328
13 2 1 Removal 328
13 2 2 Assembly 329
13 2 3 Reconditioning the final drives 330
13 3 Gearbox 334
13 3 1 Removal 334
13 3 2 Assembly 335
13 3 3 Replacing the shifter cylinders and sensor 336
13 3 4 Adjusting the shifter cylinders and sensor 337
13 3 5 Replacing the lubrication pump 340
13 3 6 Replacing the shifter forks 341
13 3 7 Reconditioning the differential 342
13 3 8 Reconditioning the gearbox 345
13 4 Hydrostatic motor 349
13 4 1 Removal 349
13 4 2 Assembly 349
13 5 Brakes 351
13 5 1 Replacing the brake blocks 351
13 5 2 Replacing the brake discs 352
13 5 3 Bleeding the brakes 354
13 5 4 Replacing the parking brake shoes 354
13 5 5 Adjustment of hydraulic parking brake 355
FENDT 9490 x – EAME 9
D3158800M2 – SIN 502000001 + SIN 502400001
Table of contents ~ -a!s! ‘ _ ,
14 Hydraulics 357
14 1 General 359
14 1 1 Hydraulics, general 359
14 1 2 Emptying and filling the hydrostatic system 359
14 1 3 Running in and bleeding the hydrostatic system 2WD 361
14 1 4 Running in and bleeding the hydrostatic system 4WD 363
14 1 5 Running in and bleeding the auxiliary hydraulics 365
14 2 Hydraulic diagrams 366
14 2 1 Standard Combines 366
14 2 2 Auto Level machines 375
14 3 Hydraulic components 386
14 3 1 Hydraulic valves 386
14 3 2 Hydraulic pumps 397
14 3 3 Hydraulic motors 404
14 4 Hydrostatic system 406
14 4 1 Transmission hydraulics 2WD 406
14 5 Gearshift 407
14 5 1 Gearshift 407
14 6 Parking brake 409
14 6 1 Parking brake 409
14 7 Auxiliary hydraulics 410
14 7 1 Auxiliary hydraulics, oil tank and oil cooler 410
14 8 Cutting table 412
14 8 1 Cutting table – hydraulics 412
14 9 Auto Level 41 5
14 9 1 Auto Level – hydraulics 415
14 10 Reel 417
14 10 1 Steering – hydraulics 417
14 11 Steering 421
14 11 1 Steering – hydraulics 421
14 12 Cutting table clutch 423
14 12 1 Cutting table engagement – hydraulics 423
14 13 Cylinder varistor 424
14 13 1 Cylinder variator – hydraulics 424
14 14 Rotor varistor 426
14 14 1 Rotorvariator- hydraulics 426
14 15 Threshing unit 428
14 15 1 Threshing mechanism on/off – hydraulics 428
14 16 Unloading auger 429
14 16 1 Unloading auger out/in – hydraulics 429
14 16 2 Unloading auger on/off – hydraulics 431
14 17 Reversing 432
14 17 1 Reversing – hydraulics 432
14 18 Chaff spreader 434
14 18 1 Chaff spreader – hydraulics 434
14 19 Maxi Spreader 435
14 19 1 Maxi Spreader – hydraulics 435
15 Electrical system 437
15 1 General 439
15 1 1 Electrical system, general 439
15 2 Description of VarioDoc 440
15 2 1 Description of VarioDoc 440
15 3 CAN connections 441
15 3 1 CAN connections 441
15 4 Failure codes 444
15 4 1 Machine-related error codes 444
15 4 2 Engine-related error codes 453
15 5 Relays and fuses 480
15 5 1 Relays and fuses 480
15 6 Connectors 486
15 6 1 Front electric box 486
10 FENDT 9490 x – EAME
D3158800M2- SIN 502000001 + SIN 502400001
~~ni T Table of contents
15 6 2 Rear electric box 488
15 7 Diagrams overview 491
15 7 1 Diagrams overview 491
15 8 Wiring diagrams 496
15 8 1 Electric diagrams, Standard Combine 496
15 8 2 Electric diagrams Auto Level machine 533
15 9 Components 569
15 9 1 Components 569
16 Straw chopper 631
16 1 General 633
16 1 1 Replacing and calibrating the electric actuator – straw deflectors 633
16 2 Hydraulic pump – Maxi Spreader 634
16 2 1 Removing the hydraulic pump 634
16 2 2 Fitting the hydraulic pump 635
17 General assembly instructions 637
17 1 Fitting gib-head keys 639
17 1 1 Fitting gib-head keys 639
17 2 Fitting tightening pins 640
17 2 1 Fitting tightening pins 640
17 3 Fitting hydraulic pipes and screw connections 641
17 3 1 Fitting hydraulic pipes and screw connections 641
17 4 Fitting a flanged bearing with locking collar 643
17 4 1 Fitting a flanged bearing with locking collar 643
17 5 Fitting sliding bushings 644
17 5 1 Fitting sliding bushings 644
17 6 Removing the revolution sensor 645
17 6 1 Removing the revolution sensor 645
17 7 Fitting tightening rings 646
17 7 1 Fitting tightening rings 646
18 Miscellaneous data 647
18 1 General 649
18 1 1 Miscellaneous data, general 649
18 2 Speeds – adjustment values 650
18 2 1 Speeds – adjustment values 650
18 3 Maintenance 651
18 3 1 Lubrication chart, intervals 651
18 3 2 Lubrication chart, right- and left-hand sides 654
18 3 3 Lubrication chart, front axles 658
18 3 4 Lubrication points, left-hand machine side 659
18 3 5 Lubrication points, right-hand machine side 678
18 3 6 Lubricants and operating fluids 692
18 3 7 Gear 694
Alphabetical index 697
FENDT 9490 x – EAME 11
D3158800M2 – SIN 502000001 + SIN 502400001
Table of contents
12
~ -a!s! ‘ _ ,
FENDT 9490 x – EAME
D3158800M2- SIN 502000001 + SIN 502400001
Table of contents a 1 Introduction – Specifications
1 1 Using the manual 15
1 1 1 Usingthemanual 15
1 2 General specifications 16
1 2 1 Dimensions and specifications 16
1 2 2 Specification table for tyres with equipment 25
1 3 Safety precautions 28
1 3 1 Safety precautions 28
1 3 2 Safety in the workshop 28
1 3 3 Safety – a word to the mechanic 28
1 3 4 Safety – danger, warning and caution 28
1 3 5 Safety decals 29
1 3 6 General 29
1 3 7 Personal safety 29
1 3 8 Considerations with regard to equipment 30
1 3 9 General considerations 31
1 3 10 Operational considerations 31
1 3 11 Maintenance techniques 32
1 4 Practical advice 34
1 4 1 Practical advice 34
1 5 Start-up instructions 38
1 5 1 General 38
1 5 2 Pre-delivery checks 38
1 5 3 Instruction of combine operator 40
1 6 Conversion tables 43
1 6 1 Conventional units of measurement 43
1 7 Locking and sealing agents 44
1 7 1 Locking and sealing agents 44
1 8 Wheel nut torques 45
1 8 1 Wheels 45
1 8 2 Bolts with metric threads 45
1 8 3 Nuts with metric threads 46
FENDT

IMAGES PREVIEW OF THE MANUAL:

Questions? Email us: [email protected]

PLEASE NOTE:

• This is the SAME exact manual used by your dealers to fix your vehicle.
• The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
• Any queries / doubts regarding your purchase, please feel free to contact [email protected]

S.M