Husqvarna FC 350 FX 350 2019 Repair Manual – PDF Workshop Guide

Description

Husqvarna FC 350 & FX 350 2019 Repair Manual

This is the full Husqvarna Motorcycles repair manual for the 2019 FC 350 (F2201S1) and FX 350 (F2201S6). Published under document number 3403085en, it is a 400-page workshop guide written for the trained mechanic who services, rebuilds and diagnoses these specific motocross and cross-country machines. Every procedure in the book is tied to the FC 350 and FX 350 model series, not a generic dirt bike platform.

File Details

• Manual type: Repair Manual / Workshop Manual
• Brand: Husqvarna Motorcycles
• Models covered: FC 350 (F2201S1), FX 350 (F2201S6)
• Model year: 2019
• Document number: 3403085en
• Publication date: 06/2018
• Language: English
• Page count: 400
• File format: PDF

Chapters Covered

• Means of Representation — symbols, formats used
• Safety Advice — repair manual notes, degrees of risk and symbols, work rules
• Important Notes — manufacturer and implied warranty, fuel and auxiliary substances, spare parts, figures
• Serial Numbers — vehicle identification number, type label, engine number, fork part number, shock absorber article number
• Motorcycle — raising with lift stand, removing from stand, starting the vehicle, function check
• Fork, Triple Clamp — air suspension AER 48, basic setting, air pressure, compression and rebound damping, bleeding, dust boots, removal and installation, full FC 350 and FX 350 fork servicing, steering head bearing
• Handlebar, Controls — handlebar position, clutch lever, rubber grips, throttle cable routing, throttle cable play, characteristic map of throttle response
• Frame — checking the frame, changing the footrests (FC 350 and FX 350)
• Shock Absorber, Link Fork — high/low-speed compression, rebound damping, rear wheel dimension, static and riding sag, spring preload, removal and installation, link fork, heim joint, full damper servicing for both models
• Exhaust System — manifold, main silencer, glass fiber yarn filling
• Air Filter — box cover, filter removal and installation, cleaning, sealing the air filter box
• Fuel Tank, Seat, Trim — filler cap, side cover, seat, fuel tank, fuel pressure, fuel pump, fuel filter, fuel screen
• Mask, Fender — front fender, start number plate
• Wheels — tire pressure and condition, wheel bearings, brake discs, spoke tension, rim run-out, front and rear wheel removal/installation, drivetrain kit, chain
• Wiring Harness, Battery — main fuse, 12 V battery, charging voltage, open-circuit current, capacitor, starter relay
• Brake System — front and rear linings, hand and foot brake lever, fluid levels and changes, brake discs
• Engine — removal and installation, full disassembly, working on individual parts, engine assembly
• Clutch — fluid level, hydraulic clutch fluid change, clutch check
• Water Pump, Cooling System — coolant level, draining, refilling, changing coolant, coolant pipe
• Lubrication System — oil circuit, engine oil level, oil and filter change, oil screen, oil pressure
• Ignition System — ignition coil, spark plug connector, alternator stator winding, stator and crankshaft speed sensor, spark plug
• Cylinder Head — valve clearance check and adjustment
• Throttle Valve Body — idle speed, initialization run
• Technical Data — engine, tolerances and wear limits, tightening torques, capacities, chassis, electrical, tires, fork, shock absorber
• Cleaning, Storage, Service Schedule, Wiring Diagram, Substances, Auxiliary Substances, Special Tools, Standards, Abbreviations, Index

The manual opens with the representation and safety conventions used throughout, then walks into the motorcycle itself — how to lift it, start it and check it. From there it works system by system through the chassis, fuel and intake, brakes, wheels, wiring and the complete engine. Each chapter follows a consistent pattern: preparatory work, main work, finishing work, with callout-numbered illustrations and guideline tables that carry the exact torque values, clearances, capacities and adjustment clicks. The fork and shock absorber chapters are particularly detailed, breaking the WP AER 48 fork and the WP 5018 DCC Link shock down to individual cartridges, pistons, shim stacks and seal ring retainers. The engine chapter goes from removal through complete case splitting, crankshaft service, transmission shaft disassembly and reassembly, and ends with the full assembly sequence and valve clearance setting. The service schedule chapter maps required and recommended work against operating-hour intervals so a mechanic can plan maintenance properly.

What This Manual Enables You to Do

With this Husqvarna FC 350 and FX 350 2019 repair manual in hand, a competent mechanic can carry out every major job on these machines. That includes full engine removal and installation, engine disassembly down to the crankshaft and transmission, connecting rod and crank pin replacement, cylinder and piston measurement, camshaft and valve service, clutch inspection and rebuild, fuel pump and filter replacement, fuel pressure testing, complete WP AER 48 fork disassembly, air cartridge and shock absorber cartridge service, shock absorber damper bleeding and nitrogen filling, steering head bearing replacement, wheel bearing replacement, brake disc and brake lining changes, hydraulic clutch fluid change, cooling system service and electrical diagnostics for the ignition coil, stator, capacitor and starter relay.

Getting these jobs right depends on having the right numbers at hand — and this manual supplies them. Air pressure for the fork, click counts for compression and rebound, spring preload, oil capacities for the fork legs and shock absorber, valve clearance tolerances, piston and cylinder mounting clearances, crankshaft run-out limits, tightening torques for everything from the top triple clamp screws to the cylinder head nuts. Without this data, home mechanics and even experienced technicians risk over-torquing fasteners, setting the wrong sag or missing a wear limit that leads to a premature failure.

Wiring Diagrams and Diagnostic Reference

The wiring diagram section is split across multiple pages and shows the EFI control unit, capacitor, 12 V battery, alternator, starter relay with main fuse, power relay, electric starter system, voltage regulator, E-tip switch and diagnostics connector — along with the fuel pump, injection valve, malfunction indicator lamp, CAN-bus terminating resistor, kill switch, intake air temperature sensor, coolant temperature sensor, rollover sensor, gear position sensor, crankshaft speed sensor, induction manifold pressure sensor, throttle valve position sensor, ignition coil and map select switch. Cable colors are listed so traces can be followed on the bike.

IMAGES PREVIEW

Instant PDF Delivery

This is an instant PDF download. There is no shipping, no waiting for a physical book, and no risk of a lost parcel. The file downloads immediately after payment and can be opened on any device — laptop, tablet, phone or workshop computer. If you prefer working from paper, every page can be printed. Keep it on a phone in the garage for quick torque reference, or print the fork and shock absorber chapters and take them to the bench. Either way, the full Husqvarna FC 350 and FX 350 2019 workshop manual is in your hands the moment you check out.