Komatsu PC200-8E0-W0 Parts Book FEN00810-00 – Illustrated Excavator Parts Catalog PDF

Description

Komatsu PC200-8E0-W0 Parts Book FEN00810-00 – Illustrated Excavator Parts Catalog

This is the complete Komatsu PC200-8E0-W0 Parts Book issued under document number FEN00810-00. It is the illustrated parts catalog used to identify and order spare parts for the PC200-8E0-W0 excavator, machine Serial No. 1003 and up, fitted with the SAA4D107E-1C-W engine, engine No. 26539574 and up. Every figure in the book is presented as an exploded illustration on one page with the corresponding index, part number, description, quantity and serial-number applicability on the facing page.

Because this is a parts book rather than a workshop manual, the goal of every page is precise identification: which part number belongs to which position in the assembly, how many are required, and from which machine serial number the part applies. The numbered callouts on each illustration link directly to the parts tables, so once the correct figure is located the exact order information is on the same spread.

File Details

• Manual type: Parts Book (Illustrated Parts Catalog)
• Brand: Komatsu
• Machine model: PC200-8E0-W0
• Engine model: SAA4D107E-1C-W
• Document number: FEN00810-00
• Machine serial coverage: Serial No. 1003 and up
• Engine serial coverage: Engine No. 26539574 and up
• Languages: English (parts listings and figure titles), with multilingual explanation sections in French, German, Portuguese and Chinese
• File format: PDF
• Page count: 379 pages

Chapters Covered

• Engine Assembly — A-Series Figures
• Engine Related Parts — B
• Cooling System — C
• Fuel Tank and Related Parts — D
• Electrical System — E
• Hydraulic System — H
• Main / Revolving Frame and Related Parts — J
• Operator’s Compartment and Control System — K
• Guard — M
• Swing Circle and Related Parts — N
• Travel and Lower Piping — P
• Under Carriage — R
• Work Equipment — T
• Marks and Plates — U
• Accessory — V
• Miscellaneous — W
• Service Kit and Component Parts — Y

Engine Assembly (A-Series Figures)

The engine section of this Komatsu PC200-8E0-W0 Parts Book covers the SAA4D107E-1C-W engine as a series of exploded assemblies. It begins with the cylinder head, showing every plug, insert, valve, collet, spring and retainer, then moves to the cylinder block and its plugs, dowel rings, caps and nozzles. Separate figures cover the front gear cover, rear gear cover fitting parts, drive cover and oil pan with its suction tube. The crankshaft assembly figure lists the crankshaft, pin, gear, collar, main bearing sets and thrust metals. The piston and connecting rod figure gives pistons, pins, ring sets, rod assemblies, bushings and metal bearings, while the camshaft figure shows the camshaft assembly, dowel, ring, gear and support. The injection pump and fuel piping figures, the fuel filter piping, the common rail and the injector assemblies are also listed, as are the rocker arm housing, breather, air intake manifold, air intake heater, exhaust manifold, turbocharger, turbocharger oil piping and heat shield groups.

Engine Related Parts (B) and Cooling System (C)

Section B covers the engine-bay dress items: the engine built-in generator, the engine mount group with its brackets, cushions, collars and mounting hardware, the air cleaner connecting parts and the pump lubrication piping. Section C is the complete cooling system, split across several figure pages so that each sub-assembly stays readable. Separate figures are dedicated to the radiator, the oil cooler, the aftercooler combined with the oil cooler, the net and shroud arrangement, the sub-tank and hybrid radiator, the oil cooler piping and condenser, the aftercooler and radiator piping, the radiator mounting and fan guard, the aftercooler piping and the hybrid cooling piping. Hoses, clips, brackets, cushions, shrouds, guards and their fasteners are all listed individually with their quantity per machine.

Fuel Tank and Electrical System (D, E)

The fuel tank section lists the tank itself, the strainer and float assembly, the filler cap and packing, the fuel level sensor, the pre-filter, the fuel filter, the fuel supply piping, the fuel drain piping, the check valve and the various elbows, o-rings and clamps that make up the lines. The electrical system opens with the battery group, including the wet battery, positive and negative terminals, holders, caps and wiring. From there it continues into the starting harness, then the three-part main harness, the battery case side wiring, the power cable, the inverter capacitor wiring and the engine bracket wiring. Horn, travel alarm and rear view monitoring circuits are also listed, with their brackets, clips, cushions, band and cable parts.

Hydraulic System (H)

Hydraulics is one of the largest sections of the PC200-8E0-W0 parts book. It starts with the hydraulic oil tank and its fittings, then moves to the main control valve, which is split into connecting parts (two figure pages) and a dedicated valve bracket and sensor figure. The main pump has its own figure, followed by the suction line, delivery line, oil cooler lines, return line, drain lines, boom line, arm and bucket line, travel line and LS lines. The solenoid valve circuit and its piping get separate figures, as does the pressure switch block and the PPC main line. The pressure switch block, solenoid valve block, nipples, unions, o-rings, flanges and every hose assembly are listed with their quantities.

Main Frame, Operator’s Compartment and Guards (J, K, M)

Section J covers the revolving frame and the boom foot pin group, together with the spacers, plates and pins that mount the boom. Section K is the operator’s compartment and control system, and it is by far the most detailed part of the book: operator’s seat (suspension and rigid type), seat belt, floor mat, window washer, air conditioner compressor, air conditioner hose, cab and window assembly, front window, front lower window, roof ventilator, door, door lock, open lock and door catch, wiper and room lamp, speaker and window washer, roof cover and air intake, pressure valve and grip, KOMTRAX film antenna and the cab-in-parts figures covering monitor cover, luggage plate, monitor duct, air duct, partition and filter, sub plate and relay, air conditioner and KOMTRAX controller, main harness clamp, rear cover, floor frame, travel control, foot rests, base, harness, harness clamp and earth, window washer hose, levers, valves, consoles, arm rests, air conditioner unit, air conditioner hose, heater hose, PPC piping for travel valve, PPC piping for pilot valve, PPC hose clamp, PT block and seal, and the rear camera cable and harness. Section M handles the guards: hood, machine cab frame, side cover L.H., side cover R.H., partition plates (left side, middle, valve and muffler side, tool box), machine cab cover, battery case, handrail, rear view mirrors L.H., R.H. and for counterweight, counterweight, counterweight mounting and under cover.

Swing Circle, Travel, Under Carriage and Work Equipment (N, P, R, T)

The swing circle section lists the swing circle assembly, swing machinery motor, the swing machinery in two halves, the gauge and drain piping and the motor drain, plus the swivel joint. Travel and lower piping covers the travel piping and the final drive with its motor, hub, bearings, carriers, gears, sprocket and the full fastener list. The undercarriage section covers the front idler, idler and cushion group, track roller, carrier roller, track shoe in the triple grouser 600 mm wide configuration with links, bushings, pins, seals and shoe bolts, track frame and track roller guard. Work equipment covers the 5.7 m boom with its top pin and arm cylinder bottom pin, arm and bucket cylinder lines, lubricating line and harness, attachment plugs, working lamp, boom cylinder, boom cylinder head pin, arm cylinder, parts for less arm, the 2.9 m arm, the bucket link for the 2.9 m arm, the bucket cylinder hose and spacer, parts for less bucket and the 0.8 m³ / 1150 mm vertical pin type bucket with teeth, cutters, shims and spacers.

Marks, Plates, Accessory, Miscellaneous and Service Kits (U, V, W, Y)

The marks and plates section lists the Chinese-language operating plates, safety and caution plates, coolant decal, KOMATSU logo plates for boom and counterweight, lubrication chart and air cleaner service instruction. Accessory covers the tool kit, including the bag, wrenches, driver, hammer, bar, grease pump, cartridge and the 12 through 30 mm sockets with extensions and handles. Miscellaneous lists the blind parts for the body and for the boom, with flanges, o-rings, bolts and connectors. The service kit and component parts section is the component-level teardown of the major assemblies: the shoe bolt and nut service kit, the 90-set track link, the rubber antenna, the operator’s seat assemblies, then the main pump broken into eleven figure pages, the boom cylinder L.H. and R.H., the arm cylinder, the bucket cylinder, the swivel joint, the travel motor in two halves, the main valve split across seventeen figure pages, both PPC valves, the solenoid valve inner parts and the air conditioner unit.

Why This Komatsu PC200-8E0-W0 Parts Book Matters in the Workshop

Ordering the wrong part on a PC200-8E0-W0 costs time the machine cannot spare, and guessing from a parts counter screen is not a safe way to confirm what is actually bolted to the machine. This book removes the guesswork. Each figure uses numbered callouts that link straight into a parts table giving the exact part number, the description and the required quantity, so the part that arrives is the part that fits. That is especially valuable on this machine because several figures carry serial-number-dependent changes: the battery case figure is only valid from Serial No. 1003, the starting motor group applies from Engine No. 26512630, and the various cooling, turbocharger and heat-shield figures carry their own applicability notes. Reading those notes before ordering avoids the all-too-common problem of receiving a part that was superseded at a serial break.

Beyond simple ordering, the exploded illustrations work as an assembly reference. When a component has to come off the machine for service — a final drive, a swing machinery case, a main control valve body, a boom cylinder head, a travel motor end cover — the figure shows every internal part, seal, ring, plate, spring and shim in the order it belongs. Rebuilding a valve block or a hydraulic motor without that reference is guesswork; with it, the assembly sequence is on the page in front of you.

The value also lies in the sheer coverage. This is not a partial catalog of the most commonly replaced parts. It is the complete book across the engine, cooling, fuel, electrical, hydraulic, frame, cab, guard, swing, travel, undercarriage, work equipment, marks and service kit sections, including the component-level breakdowns of the pump, valve, cylinders and motors that are usually missing from a general parts list.

IMAGES PREVIEW

Instant PDF Delivery — No Shipping, No Waiting

This Komatsu PC200-8E0-W0 Parts Book is delivered as an instant PDF download. Payment completes and the file is available immediately — no shipping, no customs, no waiting on a courier. The PDF opens on any Windows PC, Mac, tablet or smartphone, and any page can be printed for the workshop bench or the parts counter. Print the specific figure you are working from, keep the full book on the office machine, and the correct part number is never more than a click away. Whether you are ordering a single o-ring, rebuilding a main pump, or working through an entire undercarriage refresh, having the full FEN00810-00 parts catalog on hand pays for itself the first time it prevents a wrong part order.