Olympian 26 kVA – 200 kVA Diesel Spare Parts Catalogue Serial OLY00000KLEL03191 PDF

Description

This Olympian 26 kVA – 200 kVA Diesel Spare Parts Catalogue is the parts reference for generator set serial number OLY00000KLEL03191. It covers the 1006TAG2 engine range and the Leroy Sommer 3000 Series alternator, with exploded component drawings and part listings arranged by assembly. If you are identifying a replacement part, checking a part number before ordering, or rebuilding a known 26 kVA to 200 kVA diesel genset from this serial range, this is the catalogue to keep on the workshop PC or print for the parts bench.

File Details

• Manual type: Spare Parts Catalogue
• Document title: Spare Parts Catalogue 26 kVA – 200 kVA Diesel
• Serial number: OLY00000KLEL03191
• Engine range: 1006TAG2
• Alternator: Leroy Sommer 3000 Series
• Language: English
• Page count: 598
• File format: PDF

This is a parts catalogue rather than a workshop repair manual. Its strength is accurate parts identification: exploded views with position numbers, part numbers, descriptions and quantities, grouped by engine, alternator, cooling, fuel, electrical and baseframe assemblies. It supports parts lookup and ordering for the 26 kVA – 200 kVA Diesel range covered by serial OLY00000KLEL03191.

Chapters Covered

• S4:GENSET GHOST
• ENG/ALT RANGE. 1006TAG2
• ENGINE/ALTERNATOR. 1006TAG2
• LEROY SOMMER 3000 SERIES ALT
• ENG 1006TAG2
• Short / Long Engine
• Core Unit
• Cylinder Head
• Rocker Shaft
• Timing Gear & Camshaft
• Lubricating Oil Pump & Delivery Housing
• Cylinder Block
• Crankshaft, Pistons & Connecting Rods
• Fuel Injection Equipment
• Flywheel Housing
• Flywheel & Starter Ring
• Starter Motor
• Fan Drive
• Lubricating Oil Sump
• Lubricating Oil Filler & Breather
• Lubricating Oil Filter & Integral Oil Cooler
• Front End Drive Input
• Water Pump & Thermostat
• Water Outlet / Inlet
• Fan & Extension
• Alternator & Generator
• Gear Driven Auxiliary Drive Options
• Turbocharger, Manifolds & Air Charge Cooler
• Joints & Gaskets – Bottom Service Kit
• Low Pressure Fuel System
• Cold Start System
• Engine Lifting Eyes
• Throttle & Stop Controls
• Mountings (Front & Rear)
• Heater/Starter Switch
• Lubricating Oil Pressure Switch / Gauge
• Temperature Gauge & Sender
• Radiator & Cowling
• Fuel Pre-Lift Pump
• Application Miscellaneous & Auxiliaries
• S4:RADIATOR/FAN GROUP
• S4:BASEFRAME GROUP
• S4:FUEL LINES/BREATHER GROUP
• S4:GUARD GROUP
• S4:COUPLING GROUP
• S4:BATTERY GROUP
• S4:WIRING LOOM GROUP
• S4:EXHAUST OPTIONS GROUP
• S4:LUBE OIL DRAIN GROUP
• S4:COOLANT DRAIN GROUP
• S4:CONTROL PANEL GROUP
• Wiring diagrams, labels, documentation, toolkit and packing

Genset, engine and alternator identity

The opening groups establish the assembly structure for the 26 kVA – 200 kVA Diesel genset range. The ENG/ALT RANGE. 1006TAG2 and ENGINE/ALTERNATOR. 1006TAG2 sections connect the engine and alternator assemblies, while the Leroy Sommer 3000 Series ALT pages break down the alternator with terminal box bolts, rubber for AVR, AVR, terminal plate, varistor, earth terminal, N.D.E. terminal box, gland plate variants, N.D.E. bracket, coupling discs SAE 11 1/2, fan, diode assembly kit, rotating diode support, wound exciter armature, N.D.E. bearing, O-ring, exciter field, air inlet screen and related fixings. These pages are useful when you need to confirm alternator-side part numbers or match a terminal box and AVR component before ordering.

Long engine, short engine and core unit

The long and short engine sections cover the major engine build options, including the long engine kit, short engine assembly, cylinder block assembly, crankshaft kit and crankshaft assembly, piston kits, ring piston kit, con rod assembly and rear oil seal housing. The core unit pages carry the cylinder block, housing, seal and crankshaft, piston and connecting rod groups. This is where you look when the job involves a short block or long block build, a piston and ring replacement, or checking the correct kit part number for the 1006TAG2 engine in this serial range.

Cylinder head, rocker shaft and valve train

The cylinder head chapter lists the cylinder head kit, head gasket, plug set, cover, joints and screws, while the detailed cylinder head pages cover inserts, inlet and exhaust valves, valve guides, washers, valve seals, outer and inlet valve springs, spring caps and cotters. The rocker shaft section covers the rocker shaft assembly, rocker arm assemblies, brackets, springs, screws, olives, shims and push rods. Timing gear and camshaft pages add the timing case, gaskets, gears, hub, camshaft, thrust washer, camshaft gear, inspection cover and timing case cover. These groups are especially relevant when identifying valve train or front gear case parts from the exploded diagrams.

Lubrication, oil cooling and front end drive

Lubrication is covered across the oil pump and delivery housing, relief valve, valve, lubricating oil sump, oil filler and breather, oil filter and integral oil cooler, and front end drive input. The pages list the oil pump, relief valve components, sump, joint, dipstick, oil suction pipe, oil filler cap, breather, oil separator, oil cooler, O-rings, oil filter head, filter element, crankshaft pulley, damper, spacer, ring and thrust plate. This section helps when tracing oil leaks, identifying the correct filter head or cooler seal, or checking pulley and damper parts for the front end drive.

Cylinder block, crankshaft, pistons and connecting rods

The cylinder block section includes the block assembly, liner, oversize liner options, bearing caps, camshaft bushes, plugs, piston cooling jets, valve jets, dowels and bridge pieces. The crankshaft, pistons and connecting rods chapter covers crankshaft kits and assemblies, main bearing kits, big end bearing kits, thrust washers, conrods, small end bushes, con rod bolts, ring piston kits and piston kits. For a rebuild or bearing replacement, these are the pages that let you compare standard and undersize bearing kits and confirm the correct piston and ring set for the engine variant.

Fuel injection equipment and low pressure fuel system

The fuel injection equipment group covers the fuel injection pump, fuel injection pump breakdown, high pressure fuel pipes for each cylinder, atomisers, injectors, injector holders, injector nozzle, shims, springs, seats and clamps. The electronic governor kit and boost control pipe are also listed. The low pressure fuel system adds the lift pump, repair kit, fuel filter, filter head, fuel filter element, lift pump to filter pipe, filter to injection pump pipe, injection pump to filter pipe, leak-off rail to fuel filter pipe and the fuel pre-lift pump with pre-fuel filter assembly and primary fuel filter. This is the section for tracing fuel delivery, filter and leak-off pipe part numbers.

Flywheel housing, flywheel, starter and fan drive

The flywheel housing pages list the housing, screws, dowels, plug and seal, while the flywheel and starter ring section covers the flywheel, starter ring gear, bolts and washers. The starter motor group gives the starter motor, stud and nut part numbers. The fan drive chapter covers the fan drive housing, screw, belt, fan drive pulley, hub and bearing. These groups are practical when replacing starter drive parts, checking flywheel ring gear numbers or rebuilding the fan drive assembly.

Cooling, water pump, thermostat and radiator

Cooling coverage includes the water pump and thermostat, water pump, thermostat housing, thermostat, connections, O-rings, hoses, water outlet and inlet, fan and extension, radiator and cowling. The radiator group lists the radiator, clamps, silicone charge air outlet hose, rubber hose, fan pusher, radiator bottom hose, pipework for charge air engine inlet, beam assembly and pipe assembly. Use these pages when matching water pump repair kit parts, thermostat housing connections, radiator hoses or fan and cowling fixings.

Turbocharger, manifolds and air charge cooler

The turbocharger and manifold chapters cover the turbocharger, thrust spacer, turbocharger gasket, feed pipes, leak-off pipes, induction manifold, intake manifold gasket, pipework and connections, exhaust manifold, exhaust manifold gaskets, exhaust studs, elbows, joints, heatshield and exhaust outlet. A remote air charge cooler section is also included. These exploded views help identify turbocharger installation parts, oil feed and leak-off pipe connections, manifold gaskets and exhaust outlet fixings.

Gaskets, controls, mountings, gauges and cold start

The bottom service kit chapter lists the gasket kit and individual joints, gaskets, seals and O-rings for sump, timing case, oil seal housing, oil pump, oil filter head, lift pump and related lower-engine sealing points. Additional groups cover the cold start system with intake heater, engine lifting plates and screws, throttle and stop controls with fork, pins, brackets, spring, stud and spacer, front and rear mountings, heater and starter switch pipework, lubricating oil pressure switch and gauge, temperature gauge and sender, and application miscellaneous plugs.

Baseframe, guards, exhaust, battery, wiring and control panel

The S4 groups cover the complete generator package around the engine and alternator: radiator and fan group, baseframe tank base, plate gland, fuel fill, anti-vibration mountings, alternator and engine beams, fuel lines, fumes disposal hose kit, fan guard, guard assemblies, manifold heat guard, coupling LL3000, battery group and battery cables, wiring loom and electrical harness, industrial silencer and exhaust pipe, lube oil drain valve, coolant drain, control panel tower, AVR, MCCB breaker group, control module, terminal blocks, relays, emergency stop, RFI mounting and earth terminal kit. These pages are especially useful for package-level parts that are often missing from engine-only parts lists.

Labels, documentation, toolkit and packing

The final groups cover the labels used on the genset, including warning, coolant, oil drain, lifting, rating plate, engine information, fuel fill and alternator labels, plus the pin plate ID number. Documentation pages list operator manual and warranty items, while the toolkit and packing sections identify the standard tool kit roll and shipping bag. This makes the catalogue useful not only for mechanical parts but also for restoration-level detail such as decals and identification plates.

A practical parts catalogue for the 26 kVA – 200 kVA Diesel range

What makes this Olympian 26 kVA – 200 kVA Diesel Spare Parts Catalogue valuable is the way it pairs exploded diagrams with position-numbered parts lists. You can follow a drawing from the cylinder head through valves, springs and cotters, or from the fuel injection pump through high pressure pipes and injectors, and then confirm the part number and quantity before you call a supplier. For a 598-page catalogue tied to serial OLY00000KLEL03191, that level of assembly-by-assembly detail saves time and reduces the risk of ordering the wrong bearing size, gasket, seal or pipe.

IMAGES PREVIEW

Whether you maintain a single genset or support a fleet in the 26 kVA to 200 kVA diesel range, this parts catalogue gives you the reference you need for engine, alternator, cooling, fuel, exhaust, electrical and baseframe assemblies. It is delivered as an instant PDF download, with no shipping and no waiting for a physical book. Open it on a workshop laptop, tablet or phone, print the pages you need for the job, and keep the complete 26 kVA – 200 kVA Diesel spare parts reference ready for the next maintenance or rebuild.