Komatsu PC200F-8 Crawler Harvester Parts Book PDF – Serial B31800 and Up

Description

File Details

• Manual type: Parts Book (Parts Catalog)
• Brand: Komatsu
• Model: PC200F-8 Crawler Harvester
• Document number: KEPB006503
• Machine serial numbers: B31800 and up
• Engine: SAA6D107E-1B-W
• Engine serial numbers: 30919040 and up
• Language: English (with multilingual introduction pages in Spanish, Portuguese, Arabic, Russian, and Chinese)
• Page count: 487
• File format: PDF

What This Komatsu PC200F-8 Parts Book Covers

This is the complete parts catalog for the Komatsu PC200F-8 Crawler Harvester, built for machines from serial number B31800 upward. The engine sections apply to the SAA6D107E-1B-W diesel engine from serial number 30919040 upward. Every figure in this book pairs a numbered exploded-view illustration on the left page with a matching parts list on the right, giving you the exact Komatsu part number, description, and quantity required for each item on the machine.

Chapters Covered

• Engine
• Engine Related Parts
• Cooling System
• Fuel Tank and Related Parts
• Electrical System
• Hydraulic System
• Operator’s Compartment and Control System
• Guard and Related Parts
• Swing Circle and Related Parts
• Travel and Lower Piping
• Under Carriage
• Work Equipment
• Marks and Plates
• Accessory
• Miscellaneous
• Service Kit and Component Parts

Engine

The largest section of the book, covering the complete SAA6D107E-1B-W engine as used in the PC200F-8. Sub-assemblies include the cylinder head (with valve kits, springs, retainers, and gaskets), lifting bracket and mounting, head cover, breather and hose, air intake connector and heater, exhaust connector clamp, exhaust manifold, turbocharger and oil piping, heat shield, thermostat, water outlet connector, tappet and plate, cylinder block, front and rear gear covers, oil pan, oil level sensor and gauge, flywheel housing, flywheel, crankshaft, damper, piston and connecting rod, rocker arm assembly, camshaft, rear gear housing, accessory drive pulley, oil pump, oil filter and piping, oil cooler, fuel system and fuel injection pump, fuel filter and piping, common rail and injector, fuel injection controller, water inlet connector, water pump, cooling fan drive pulley, fan spacer, alternator mounting, belt tensioner, starting motor mounting, wiring harness, air transfer connection, and air cleaner. Both standard and optional equipment parts are listed.

Engine Related Parts

This chapter covers items mounted to or around the engine rather than internal to it: damper, exhaust muffler and mounting bracket, oil pan drain, cooling fan, 35A and 80A alternator options with mounting, 4.5KW starting motor, engine mount brackets and cushions, air cleaner assembly (with pre-cleaner specification), air cleaner connecting parts, and pressure kit.

Cooling System

Radiator, oil cooler, shroud and after-cooler, fuel cooler and condenser (air-conditioned machines), fan guard and after-cooler piping, and the cooling-tank radiator catching arrangement. Hose, clamp, shroud, sheet, and seal part numbers are provided per sub-assembly.

Fuel Tank and Related Parts

The main fuel tank, extra 210L diesel tank, fuel tank strainer, frontal protector, case saw and chain option, main switch and latch key, external extinguisher, fuel supply piping, drain piping, and the pre-filter assembly.

Electrical System

Battery (170 Ah, large capacity), starting harness, main harness (split into two parts), engine-side wiring, battery case-side wiring, additional work lamp, horn, travel alarm, rear view monitoring system, head lights (including LED variants), head light wiring, connection box, and support. Both standard and LED head light variations are covered with serial ranges.

Hydraulic System

Hydraulic oil tank, vacuum pump, quick coupling, main control valve with 1-additional-actuator piping and accumulator, main pump (for 1-actuator), suction line, delivery line, oil cooler lines, return filter, drain lines, boom line, arm and bucket lines (with and without arm holding valve), attachment lines, travel line, swing lines, LS lines, solenoid valve circuit, pressure switch block, proportional pressure control (PPC) main piping, and pilotage kit. The hydraulic section is one of the most detailed in the book.

Operator’s Compartment and Control System

Operator’s seat (suspension type), seat belts (78mm and 4-point), top guard, protection top guard, floor mounts, floor mat, carpet, window washer, air conditioner, heater, and the operator’s cab — broken into window, roof ventilator, door, Lexan cab, rear emergency exit, door lock, door latch, open lock and door catch, wiper and room lamp, speaker and window washer, roof cover and air intake, pressure valve and grip, KOMTRAX film antenna, front Lexan, Lexan 12.7mm, cab-in-parts sections (monitor and cover, luggage plate, monitor duct, air duct, partition and filter, sub plate and relay, air conditioner and KOMTRAX controller, main harness clamp, rear cover, floor frame, travel control, foot rests, base, harness, harness clamp and earth, window washer hose, lever L.H., valve L.H., console L.H., lever R.H., valve R.H., console R.H., arm rest, slope indicator, air conditioner unit, air conditioner hose, heater hose, P.P.C. piping for travel valve, P.P.C. piping for pilot valve, P.P.C. hose clamp, P/T block and seal, rear camera cable), control box, support computer, level sensor kit, CD player, voltage converter, MaxiFleet Wi-Fi, and mode selection connectors.

Guard and Related Parts

Hood, hood (net), machine cab frame, side covers L.H. and R.H. (including frame versions), partitions (left side, middle, valve and muffler side, with air conditioner), machine cab covers (with pre-cleaner), battery case, battery case spring, counterweight (3730KG), counterweight mounting, under covers (split into 1/2 and 2/2), protector engine, catwalk, and additional protection items.

Swing Circle and Related Parts

Swing circle assembly with seals, nipples, bolts, pins, caps, tube, elbow, clip, and plugs; swing machinery including motor, case, bearings, shaft, cover, carrier, gears, pins, plates, and washers; swing machinery gauge and drain piping; and the swivel joint with its elbows, tees, flanges, heads, and O-rings.

Travel and Lower Piping

Travel piping, final drive (with serial ranges for B31800–B32713 and B32714–B32821), travel motor and final drive (split into L.H. and R.H. for serial B32822 and up), under carriage with front idler, idler and cushion (idler cushion), track roller, carrier roller, track shoe (triple grouser with hole, 600mm wide, with separate serial ranges B31800–B32263 and B32264 and up), track frame, under cover (for track frame), track roller guard, full roller guard, and protector greasing.

Work Equipment

Boom (5.7M, 100-hour greasing type) with top pin and arm cylinder bottom pin, arm and bucket cylinder lines, lubricating line and harness, attachment plug, additional lines, working lamp; boom cylinder head pin; boom cylinder (L.H. and R.H., 100-hour greasing type); arm cylinder (100-hour greasing type); arm (2.9M, 100-hour greasing type, with multiple serial ranges); arm lubrication piping and additional piping; pin lubrication; anchorage points boom; protector of transmission hoses; boom cylinder guard; and tip adapter.

Marks and Plates

Mark and name plates in English, lubrication chart, caution plates (cab windshield lock operation, arm, KOMTRAX, swing/backing up warning), coolant decal, Komatsu logo (boom and counterweight), ROPS plate (Portuguese), and adhesive kit.

Accessory and Miscellaneous

Spare parts kit (packings, isolators, cartridges, belt, element, O-rings, fittings), tool kit (bag, wrenches, driver, hammer, bar, grease pump and cartridge, sockets, extensions, handles), step assemblies, heat shields (1/2 and 2/2), fire suppression unit (auto and manual, split into 5 parts each), lubrication automatic assembly, and off line filter.

Service Kit and Component Parts

Swing machinery assembly for supply, shoe bolt and nut service kit, track link assembly (90 set) for supply parts (with serial splits), fuel self-charge pump inner parts, rubber antenna, and the full main pump breakdown across 11 figures (case, cap, shaft, bearings, block, cylinder, plate, valve, piston, cradle, servo, regulator, cover, coupling, and pilot valves).

How the Parts Book Is Organized

Each figure is numbered in the FIG. NO. column, with an index number that matches the callout on the facing illustration. The PART NO. column gives the exact Komatsu part number to quote when ordering. The DESCRIPTION column uses a dot prefix to show component hierarchy — a single dot marks a direct component of the assembly above, and a double dot marks a sub-component. The Q’TY column shows how many of that part are used per machine or per assembly. The SERIAL No. column tells you which serial range the part applies to, which matters because several assemblies changed during PC200F-8 production (for example the alternator, starting motor, travel motor/final drive, and track shoe).

Why This PC200F-8 Parts Book Matters

Ordering the wrong part for a Komatsu PC200F-8 wastes time and money, especially on assemblies that changed mid-production. This book removes the guesswork — every part number is tied to a specific figure, quantity, and serial range. Whether you are rebuilding a SAA6D107E-1B-W engine, replacing a final drive on a machine above or below serial B32821, sourcing a Lexan cab panel, or identifying the correct O-ring from the hydraulic oil tank diagram, the correct number is in this catalog.

IMAGES PREVIEW

Instant PDF Delivery

This Komatsu PC200F-8 Crawler Harvester Parts Book is delivered as an instant PDF download — no shipping, no waiting. Open it on a workshop PC, a tablet on the machine, or a phone in the yard. Print the pages you need for the job and keep the rest of the 487-page catalog on file. If you maintain, repair, or rebuild a PC200F-8 from B31800 onward, this is the parts reference you want within reach.