FENDT Katana 65 S4 Maintenance Operator’s Manual – PDF DOWNLOAD

Description

FENDT Katana 65 S4 Maintenance Operator’s Manual – PDF DOWNLOAD

DESCRIPTION:

FENDT Katana 65 S4 Maintenance Operator’s Manual – PDF DOWNLOAD

1.1 Introduction
1.1.1 Safety instructions: Introduction
Operator’s Manual
NOTE:

• This Operator’s Manual is published and distributed across various markets. The availability of the components referred to – whether as part of the standard equipment or as an accessory – can vary depending on the country or region concerned. If you would like to know what equipment features are available in your region, you should
• contact your FENDT dealer. Under normal conditions, this Operator’s Manual should enable the owner and operator to operate the forage harvester safely. If these instructions are followed, the forage harvester, like all FENDT products, will provide faithful service for many years. The FENDT dealer’s commissioning at the operator’s
• site ensures that you understand both the operating and service instructions. You should contact your FENDT dealer if you do not understand any parts of this Operator’s Manual. It is essential that these instructions are understood and observed. The instructions do not contain all of the safety and operating instructions for the
• attachments and accessories that can be fitted at the time of delivery and after delivery of the forage harvester. It is imperative that the operator understands and uses the Operator’s Manual relative to these attachments and the accessories.

IMPORTANT:

• This manual must always be kept in the forage harvester. You can obtain a copy of this Operator’s Manual from your FENDT dealer. This chapter of the Operator’s Manual contains a description of specific safety-related
• standard situations that can arise when operating the forage harvester and during normal maintenance. You are also given all of the information required on the correct behavior to adopt in these situations. This chapter is
• supplementary to the safety instructions contained in other chapters of this Operator’s Manual. Depending on the attachments used and the working conditions on-site or in the maintenance area, additional precautionary
• measures may need to be taken. FENDT has no direct influence on the commissioning, operation, inspection, lubrication or maintenance of the forage harvester. YOU are therefore responsible for the adoption of appropriate safety measures in the areas concerned.

TABLE OF CONTENTS:

FENDT Katana 65 S4 Maintenance Operator’s Manual – PDF DOWNLOAD

1 Safety instructions 9
11 Introduction 11
111 Safety instructions: Introduction 11
2 Service and maintenance 13
21 General 15
211 General notes on maintenance 15
22 Trims 17
221 Unlock and open engine cover 17
222 Unlock and open panels on the left and right 17
223 Unlock and close panels on the left and right 18
224 Unlock and open service area door 19
23 Feed system 20
231 Detach intake assembly 20
232 Attach intake assembly 24
24 Cutting unit 29
241 Cutting cylinder bearing mounting wedges 29
242 Replace knives 29
2421 Remove knives 29
2422 Install knives 31
243 Adjust knives 33
2431 Remove knives 33
2432 Install knives 35
244 Drum modification to half number of knives 37
2441 Remove knives 37
2442 Install cover plates 39
245 Adjust drum base 41
25 Grinding device 43
251 Replace or readjust grindstone 43
26 Shear bar 46
261 Manually move the shear bar to the maintenance position 46
262 Move shear bar automatically to maintenance position (optional) 48
27 Engine 51
271 Engine oil 51
2711 Check the engine oil level using the terminal 51
2712 Fill with engine oil 52
2713 Drain the engine oil 52
2714 Change the engine oil filter 52
272 Cooling system 53
2721 Check cooling and heating system 53
2722 Check the coolant level 53
2723 Re-fill with coolant 54
273 Fuel system 55
2731 Change the fuel filter 55
274 Dry air filter 56
2741 Remove and fit the dry air filter 56
275 V-belt 57
2751 Check engine poly-V belt 57
28 Transmission 59
281 Check oil level in main transmission 59
282 Fill main transmission with oil 59
283 Drain main transmission oil 59
284 Replace main transmission intake filter 60
29 Rear axle and flange gearbox 61
291 Check oil level of flange gearbox and unsuspended rear axle 61
2911 Check oil level of flange gearbox 61
2912 Check oil level of rear axle 61
292 Check oil level of flange gearbox and suspended rear axle 62
2921 Check oil level of flange gearbox 62
2922 Check rear axle oil level 62
293 Top up oil in flange gearbox and unsuspended rear axle 63
2931 Refill oil in flange gearbox 63
2932 Filling rear axle with oil 63
294 Top up oil in flange gearbox and suspended rear axle (652, 653) 64
2941 Filling flange gearbox with oil 64
2942 Filling rear axle with oil 64
295 Drain oil from flange gearbox and rear axle 65
296 Drain oil from flange gearbox and rear axle 65
210 Wheel drive 66
2101 Check oil level in front axle wheel reduction unit 66
2102 Change oil in front and rear wheel reduction hubs 67
211 Hydraulics 68
2111 Check the hydraulic oil level in the terminal 68
2112 Check the hydraulic oil level at the sight glass 69
2113 Drain hydraulic oil 69
2114 Replace suction line filter 71
2115 Clean high-pressure filter 72
21151 Remove the high-pressure filter 72
21152 Disassemble the high-pressure filter 73
21153 Install the high-pressure filter 73
212 Belt drives 75
2121 Check drive belts 75
2122 Check cracker drive belt 75
2123 Check and adjust fan drive belt 76
21231 Visual inspection of fan belt 76
21232 Check and adjust the belt tension 76
213 Wheels/tires 77
2131 Check and maintain tires 77
2132 Tire pressures 78
2133 Change wheels 81
214 Electrical system 83
2141 Interference with electrical system and troubleshooting 83
2142 Batteries 83
2143 Electric welding 84
2144 Fuse holder and fuse assignment (X1441 to 1445) 84
2145 Installation of additional electrical and electronic equipment 90
215 Compressed air system 92
2151 Draining condensation water from the air receiver 92
216 Air-conditioning system 93
2161 Clean air conditioning condenser 93
217 Central lubrication 94
2171 Filling 94
21711 Fill the pump with a commercially available grease gun 94
21712 Fill using filling station or filling gun 94
218 Cleaning 95
2181 Cleaning the machine 95
2182 Clean the terminal 96
3 Faults and remedy 97
31 Information and fault messages 99
311 Information and fault messages in the terminal 99
32 Fault code tables 100
321 Error code 01100 101
322 Error code 02100 104
323 Error code 03100 113
324 Fault code 04100 115
325 Fault code 05100 130
326 Fault code 06100 133
327 Fault code 07100 135
328 Fault code 08100 142
329 Fault code 09100 150
3210 Fault code 0A100 151
3211 Fault code 0B100 172
3212 Error code 0D100 174
3213 Error code 0F100 176
3214 Error code 11100 186
3215 Fault code 15100 187
3216 Error code 16100 189
3217 Fault code 18100 190
3218 Fault code 1D100 194
3219 Error code 1E100 203
3220 Fault code 1F100 230
3221 Error code 20100 231
3222 Error code 32100 236
3223 Error code 33100 242
3224 Error code 34100 252
3225 Fault code 35100 258
3226 Error code 36100 263
4 Technical specification 265
41 Technical specification 267
411 Technical data: general for Katana 65 S4 267
412 Technical data: Diesel engine R6 Katana 65 S4 269
413 Technical data: Gearbox 271
414 Technical data: Hydraulic system 271
415 Technical data: Rear axle (without suspension) 271
416 Technical data: Rear axle (with suspension) 272
417 Technical data: Cab/air-conditioning system 273
418 Technical data: Brakes 274
419 Technical data: Electrical system 274
4110 Technical data: Feed equipment 274
4111 Technical data: Cutting unit and corn cracker 274
4112 Technical data: discharge system 275
4113 Technical data: Central lubrication 276
42 Fuels and lubricants 277
421 General 277
422 Filling quantities 277
423 AdBlue® 279
5 Lubrication and maintenance plan 281
51 Lubrication chart 283
511 Filling points 283
512 Lubrication points and intervals 287
513 Central lubrication 295
52 Maintenance schedule 300
521 Tightening torques 300
522 Maintenance schedule 302
6 Vehicle registration 309
61 Vehicle registration on AGCO Net 311
611 Vehicle registration on AGCO Net 311
7 Index 313
Table of contents
Maintenance
IMAGES PREVIEW OF THE MANUAL:

VIDEO PREVIEW OF THE MANUAL:

PLEASE NOTE:

• This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
• The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes
• time!!
  Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer
  

s.m