KRONE Comprima CF 155 XC X-treme & CV 150 XC X-treme Round Baler Operating Instructions Manual 15000016608 – PDF Download

Description

KRONE Comprima CF 155 XC X-treme and CV 150 XC X-treme Operating Instructions Manual – PDF

This is the complete English operating instructions manual for the KRONE Comprima CF 155 XC X-treme and Comprima CV 150 XC X-treme round balers. It is identified by order no. 150 000 166 08 en and dated 14.11.2018, and it applies from serial no. 995 323. Across 386 pages, the manual documents the machine from initial commissioning and road transport through field operation, ISOBUS terminal menus, net and film wrapping, cutting system adjustment, maintenance, lubrication, hydraulics, troubleshooting, storage, and disposal. Whether you are running a Comprima CF 155 XC X-treme or a Comprima CV 150 XC X-treme, this Krone Comprima X-treme operating instructions manual is the reference for correct procedures, settings, and service intervals.

File Details

• Manual type: Original operating instructions for round baler
• Brand: KRONE
• Models: Comprima CF 155 XC X-treme, Comprima CV 150 XC X-treme
• Language: English
• Page count: 386
• File format: PDF
• Order no.: 150 000 166 08 en
• Date: 14.11.2018
• Serial range: from serial no. 995 323

Chapters Covered

• 1 Table of Contents
• 2 To this Document
• 3 Safety
• 4 Data memory
• 5 Machine Description
• 6 Technical data
• 7 Commissioning
• 8 Start-up
• 9 KRONE ISOBUS Terminal
• 10 Foreign Terminal ISOBUS
• 11 Terminal – Machine Functions
• 12 Terminal – Menus
• 13 Driving and Transport
• 14 Operation
• 15 Settings
• 16 Maintenance
• 17 Maintenance – lubrication
• 18 Maintenance – hydraulic system
• 19 Malfunctions – Causes and Remedies
• 20 Placing in Storage
• 21 Disposal of the machine
• 22 Appendix
• 23 Index

Safety

The Safety chapter is extensive and begins with purpose of use, intended use, and service life. It then sets out basic safety instructions covering personnel qualification, children in danger, safe coupling, structural changes, additional equipment and spare parts, workstations, operational safety, danger zones, safety devices, personal protective equipment, safety signs, traffic safety, parking, consumables, environmental dangers, overhead lines, noise, high-pressure liquids, hot surfaces, climbing, work on the machine, wheels and tyres, and accident behaviour. Safety routines explain how to stop and secure the machine, support lifted components, check oil and change filters safely, and run the actuator test. Safety stickers and their positions are also documented, along with the quick-stop switch, safety loops, parking brake, support jack, wheel chocks, tailgate shut-off valve, wrapping table rollers, ladder, and SMV emblem.

Machine Description and Technical Data

This part identifies the machine overview, type plate, and information required for questions and orders. The technical data section lists the main dimensions and capacities for both models, including pick-up width, track width, tyres, bale size, maximum bale weight, power requirement, PTO speed, hydraulic pressure and delivery, electrical supply, net and film roll dimensions, and overload protection. It also lists hydraulic connections, consumables, oil types and filling quantities, lubricating greases, and ambient temperature range.

Commissioning and Start-up

Commissioning covers the work required before initial start-up, including preparatory tasks, removing the transport tensioning device, checking the guide wheel support, adjusting drawbar height and hitch, PTO shaft length and machine-side mounting, hose support, wrapping material brake preparation, and tyre pressure. Start-up covers connecting the machine to the tractor, hydraulic hoses, hydraulic brake, PTO shaft installation, compressed air connections, KRONE ISOBUS terminal, external ISOBUS terminal, joystick, electrical connections, safety chain, running-in period, cam-type clutch engagement, wrapping table, bale cloth, and bale turner setup.

KRONE ISOBUS Terminal and Foreign Terminal ISOBUS

These chapters explain ISOBUS general information, the ISOBUS shortcut button, touch-sensitive display, switching the terminal on or off, display design, status line, keys, main window, and switching between terminals. The foreign terminal chapter covers ISOBUS operation when no KRONE terminal is used, including the shortcut button not being available and functions that differ from the KRONE ISOBUS terminal.

Terminal – Machine Functions

This section explains how machine and terminal functions work together. It shows how to call the working screen, read the status bale chamber screen, operate machine functions, set bale diameter, set baling pressure, switch working floodlights, and operate the hydraulic blade group control system. It also covers joystick operation, auxiliary functions, and auxiliary assignment of a joystick.

Terminal – Menus

The menu chapter provides the full menu structure and step-by-step settings. It includes baler settings, number of net layers, number of film layers, advance signalling, tying start delay for net wrapping and film tying, bale diameter, electronic baling pressure adjustment, sensitivity of direction display, tying type selection, filling correction, wrapping device settings, number of film layers rear, correction for wrapping arm film wrappings, wrapping device mode, wrapping table mode, film width, film tear control, weighing device, manual operation, counters, customer counter, total counter, ISOBUS settings, diagnostics auxiliary, background colour, TIM software configuration, switching number of keys, switching between terminals, settings, sensor test, actuator test, software information, technician level, diagnostics, and manual operation without confirmation prompt. Error messages, query messages, alarms, physical messages, and acoustic warnings are also documented.

Driving and Transport

This chapter prepares the machine for road travel. It covers moving the support jack into transport position, checking the lighting system, attaching the bale cloth, folding in the bale turner, switching off the machine, disconnecting the PTO shaft and supply lines, preparing for transportation, raising the machine, securing side hoods, securing the twine box flap, securing the guide wheels of the pick-up, and mounting the transport tensioning device.

Operation

Operation covers adjustments before starting work, travelling speed, filling the bale chamber, reducing pressure on the side walls, mounting additional driver guide rails, removing sliding plates, mounting additional deflector sheets, tying and depositing round bales, before and after baling, overload protection, drive chain for pick-up with cam-type clutch, using the bale turner, disconnecting the hydraulic pump gearbox from the main drive, pick-up settings, bearing pressure relief, roller crop guide, baffle sheet, cutting system, cutting length, bale diameter, baling pressure, building minimum pressure, net wrapping, net and chamber film wrapping, checking tension springs, setting bale core density, wrapping device operation, inserting sheet, checking wrapping film, adjusting sheet brake, adjusting prestretching, adjusting gearbox on wrapping table, replacing stretch rolls, and removing crop blockages.

Settings

Settings includes brake force release during feeding, wrapping material brake adjustment for net and film tying, locking and releasing the clamping lever, setting the lock of the conical roller, checking the retaining comb for net tying and film tying, setting the retaining comb for film tying, checking the position of the feed rocker arm, and the central chain lubrication system including oil checking, bleeding, nozzle sizes, and lubrication point diagrams.

Maintenance, Lubrication, and Hydraulic System

Maintenance covers spare parts, maintenance table, tightening torques for metric threads and gearbox locking screws, scraper settings, sensor positions and settings, axial play of net brake, paint and welding residue removal, tandem axle brake setting, tyres, drawbar, gearbox oil level and changes, Novo Grip belt, safety rollers, rear floor conveyor, wrapping table chain, drive chains, blade changing, blade grinding, blade retaining shaft, and brake system maintenance. Lubrication covers lubricants, universal shaft, WALTERSCHEID cam-type clutch, and lubrication points. Hydraulic system maintenance covers the tailgate shut-off valve, on-board hydraulics, emergency manual operation, solenoid valves, hydraulic oil tank, hydraulic oil filter, and hydraulic circuit diagrams.

Malfunctions, Storage, Disposal, and Appendix

The malfunctions chapter lists general faults, causes, and remedies; central chain lubrication faults; wrapping mechanism faults; job computer faults; TIM faults; and KRONE operation terminal error messages. Storage covers end-of-season preparation and before the new season. Disposal explains metal, fluids, synthetic materials, rubber, and electronic scrap. The appendix contains hydraulic circuit diagrams for the Comprima CF 155 XC X-treme and Comprima CV 150 XC X-treme, with valve legends and icon meanings.

Why the KRONE Comprima CF 155 XC X-treme and CV 150 XC X-treme Operating Instructions Manual Is Essential

This manual gives you the procedures and reference values to run, adjust, and maintain the round baler correctly. You can set bale diameter and baling pressure, configure net or film tying, operate the ISOBUS terminal, troubleshoot error messages, service the wrapping device, adjust the cutting system, and follow maintenance intervals for chains, gearboxes, hydraulics, and brakes. Correct settings and service procedures protect bale quality, machine reliability, and safe operation.

IMAGES PREVIEW

Because it covers both Comprima CF 155 XC X-treme and CV 150 XC X-treme models from serial no. 995 323, it is a practical workshop and operator reference for the complete machine. The PDF is available for instant download after purchase, with no shipping and no waiting. Use it on a laptop, tablet, or phone in the workshop or field, and print only the pages you need for the job at hand.