Still RX20-15 RX20-16 RX20-18 RX20-20 Electric Forklift Spare Parts Catalogue 2012 – PDF

Description

Still RX20-15, RX20-16, RX20-18 and RX20-20 Electric Forklift Spare Parts Catalogue – 2012 Edition

This is the illustrated spare parts catalogue for the Still RX20-15, RX20-16, RX20-18 and RX20-20 four-wheel electric counterbalance forklift range. Issued through the Still Electronic Documentation System under document number 516210C00789 and dated 10.09.2012, the 727-page catalogue takes the truck apart group by group and lists every orderable component with its Still part number, quantity, description and validity period. It is the reference a parts counter, workshop or fleet owner works from when a component has to be identified, ordered or matched to a truck built inside a particular production window.

File Details

• Manual type: Illustrated spare parts catalogue (Ersatzteilliste)
• Brand and range: Still RX20 electric counterbalance forklift
• Models covered: RX20-15, RX20-16, RX20-18, RX20-20, including the RX20-16 Komatsu variant
• Document number: 516210C00789
• Document code: 0 170 022 – 08/2005
• Date: 10.09.2012
• Language: English and German (spare parts catalogue with multilingual cover and documentation index)
• File format: PDF
• Page count: 727 pages

Chapters Covered

• Documentation – operating instructions by battery brand, service booklet, check book, guidelines by language, spare parts list on CD-ROM
• Motor – traction motor assembly left and right, AT drive motor, GT drive motor, stator, rotor, bearing shield, terminal box
• Drive unit, complete – drive axle, pump motor, spring elements, guard plate, protective cover
• Drive wheel unit – left and right, radial seal rings, bearing bushes, sensor transmitter impulse, hydraulic service brake group
• Brake kit – pressure plate assembly, fit bolts, actuation assembly, tension spring
• Pump motor – drive bearing, shaft seal, rubber mounting, armature, terminal box
• Chassis – frame, floorplate, standard and signal-switch versions, travel sender
• Counterweight – counterweight, bolt assembly, spring cover, adhesive
• Panels – chassis covering, counterweight covering, cabin covering, protective cover, foot board, side panel
• Operator’s compartment – driver cabin, roof panel, mirror, door complete, sidewall assemblies
• Driver seat – MSG 65 seat, harness, pipe, cable clips, pin housing
• Overhead guard – standard and container versions, repair kits
• Steering system – key switch, steering wheel with steering column, operating elements, steering axle assembly
• Steering axle – steering box, tapered roller bearings, axle casing, wheel hub, rack rail, cylinder pipe
• Wheels and tyres – wheel assembly, superelastic tyres, solid tyres, disc wheels, wheel screws and nuts
• Braking system – hydraulic service brake, mechanical service brake, parking brake, handbrake control
• Controls – acceleration and braking control, one-pedal and two-pedal versions, ignition switch
• Display element – support console with and without card reader, control unit
• Electrics and electronics – power supply 24 V, CAN power port, relay plate, conversion kit
• Wiring – control cable looms for chassis and overhead guard, cable trees, electric cables, earth cables
• Lighting – lamp conversion kit 24 V to 48 V, headlights front and rear, wiring harnesses
• Electrical installation – roof, frame, counterweight, horn, fuse holder, solenoid, contactor, covering
• Hazard warning system – warning light, flashing lamp, transducer
• Battery and accessories – battery overview 48 V, battery connectors, water tank, appliance plug assembly, battery harness, retrofit kit
• Electronic controls – controller, converter SAC1 48 V, support
• Hydraulic – basic hydraulics, gear pump, valve, suction filter, return flow filter with breather filter, oil supply lines, high pressure hoses
• Pipes and tubes – lift cylinder connection pipes
• Working hydraulics – pump unit, pump motor, solenoid valve, control valve block, directional control valve block with ISO function
• Working hydraulic controls – series lever, direction switch, tilt lever, third lever, symbol plates
• Tilt cylinder – complete cylinder, cylinder pipe assembly, piston, piston rod, cylinder head, seal kits
• Additional hydraulics – in the truck and on the mast, one-function and pre-load valve versions, retrofit kits
• Attachment hose – triplex and triple configurations, hose guides, pulleys, hose lines by length
• Load lifting system – mast pivot, mast bearing assembly left and right, spherical bearings, lubricators
• Mast – outer mast, intermediate mast, inner mast, common parts, rollers, check valves, chain rollers
• Lift cylinders – right, left and centre, piston rods, cylinder barrels, cylinder head assemblies, seal kits
• Lift chains – outer mast chains and centre chains with lengths
• Load carrier – fork carriage, load support, screen grid, fork arms
• Fork arms – ISO fork tines, form A, fork retaining pin assembly
• Attachments – bale clamp, forkshift, clamp fork, double clamp, rotator, mandrel, crane jib, telescopic forks, bucket, snow remover, fork extensions
• Other accessories – load capacity plate, identification plate, product identification, warning and instruction stickers, inspection medallions
• Part number index – complete alphabetical listing of every Bestell-Nr. with its page reference

Read as a whole, the catalogue maps the complete RX20 truck from the traction motors and drive wheel units through the chassis, covering, operator station and steering, across to the electrical architecture with its controllers and converters, and then through the hydraulics out to the mast, lift cylinders, chains and load carrier. Each group is presented as an exploded illustration keyed to a parts table, so a technician can see how a component sits inside its assembly before ordering it, and can trace which neighbouring parts, seals, bearings, washers or fasteners have to be replaced at the same time. The document also carries the documentation chapter, which lists the operating instructions and service literature issued for these trucks by battery brand and language.

How the part lists are organised

Every parts table in this Still RX20-15 RX20-16 RX20-18 RX20-20 spare parts catalogue follows the same column layout: position number, Bestell-Nr. (order number), Menge (quantity), Name, Ausfuehrung (version or variant), Gueltigkeit (validity) and Fahrzeuge (vehicle applicability). The position number is the callout that ties the line to the drawing above it, so a part can be read straight off the exploded view and looked up in the table underneath. Where a component exists in several versions – a left and a right traction motor, a standard and a container overhead guard, a metal or plastic foot board, a standard or scratch-resistant polycarbonate sidewall – the Ausfuehrung column separates them so the correct variant is ordered the first time. Quantities are given per assembly, which is what makes the catalogue usable for planning a full rebuild rather than just a single replacement part.

Production cut-offs and superseded parts

One of the most valuable features of this catalogue is the Gueltigkeit column. Instead of presenting one flat list that pretends every truck was built identically, it shows where a part was used only up to a date and where a replacement took over. Cut-offs such as 30.01.2005, 05.09.2010, 05.10.2008, 15.03.2009, 12.05.2011, 02.08.2012 and 04.05.2012 appear against individual line items, and several entries explicitly state that an item is no longer available and point to the substitute. Vehicle applicability codes such as R6209, R6210 to R6217, R6311, R6313, R6315 and R7311 to R7316 run alongside them, separating which build of truck a line applies to. For anyone maintaining a mixed fleet, or trying to work out why the part on the bench does not match the drawing, this is the difference between ordering once and ordering three times.

The back of the file closes with a full part number index running across 27 pages, listing every Bestell-Nr. in numerical order together with the page on which it appears. That index turns the catalogue into a reverse-lookup tool: if a part number is known but the assembly it belongs to is not, the index sends you straight to the correct group instead of paging through the whole document.

What this catalogue lets you do

With this Still RX20 electric forklift spare parts catalogue on hand you can identify and order the correct component for an RX20-15, RX20-16, RX20-18 or RX20-20 without relying on guesswork or on a dealer looking it up for you. You can rebuild a traction motor or a drive wheel unit, replace brake components, seals and bearings in the drive axle, source the right solenoid valve or control valve block for the working hydraulics, match a lift cylinder or lift chain to the mast configuration actually fitted to the truck, and track down the small items – clamps, half clips, shim rings, detent rings, cable clips, oval head screws – that stop a repair halfway through. You can check whether the truck in front of you was built before or after a production change and order the version that actually fits. And you can put together a complete parts list for a scheduled overhaul rather than discovering the missing seal once the machine is already apart.

Getting the part number right the first time matters on an electric counterbalance truck: a wrong seal kit, bearing shield or valve body means a machine standing idle while a second order is placed. This catalogue removes that risk by showing the assembly, the variant and the validity window together on the same page.

IMAGES PREVIEW

The catalogue is supplied as an instant PDF download. There is nothing to wait for in the post, no shipping charge and no regional restriction. Open it on a workshop laptop, a tablet on the shop floor or a phone beside the truck, print the pages for the assembly you are working on and take them to the bench, or keep the whole 727-page file searchable on a shared drive so the whole team can reach the same part number. Once payment is complete the download is available immediately.