Linde H12 H16 H18 H20 D-03 T-03 Series 350 Service Training Manual

Description

Linde H12 H16 H18 H20 D-03 T-03 Series 350 Service Training Manual

This Linde H12 H16 H18 H20 D-03 T-03 Series 350 Service Training Manual is a complete technical training document for the Linde IC engine truck range equipped with Linde Hydraulic Control (LHC). It covers the H 12, H 16, H 18 and H 20 models in both D-03 diesel and T-03 LPG configurations, series 350, and provides the detailed procedures, specifications and diagnostic information needed to service, maintain and repair these machines correctly.

Whether you are a workshop technician, fleet maintenance engineer or an operator responsible for keeping a Linde H-series truck running, this manual gives you the manufacturer-level training content in a single, searchable PDF file.

File Details

• Manual Type: Service Training Manual
• Brand: Linde
• Model Range: H 12, H 16, H 18, H 20
• Variants: D-03 (Diesel) and T-03 (LPG)
• Series: 350
• Control System: Linde Hydraulic Control (LHC)
• Language: English
• Page Count: 238
• File Format: PDF
• Document Number: 350 804 4701.0201

Chapters Covered

• 1. Diesel Engine
  • Engine Specifications
  • Crankshaft
  • Adjusting Alternator V-Belt Tension
  • Removing Toothed Belt
  • Fuel Injection Pump
  • Removing and Installing the Fuel Injection Pump
  • Removing and Installing the Crankshaft Sprocket
  • Check and Adjust Static Injection Pump Timing
  • Checking Engine Timing
  • Stop Leaks from the Adapter of the Injection Pump
  • Adjust the Idling Speed and the Governed Speed
  • Fuel Injectors
  • Remove and Install Fuel Injectors
  • Servicing Fuel Injectors
  • Fuel Injector Parts
  • Check Injector Needle Tip
  • Check of Fuel Pressure
  • Check for Leakages
  • Cylinder Head
  • Cylinder Head Removal
  • Check Cylinder Head for Distortion
  • Markings of Cylinder Head Gaskets
  • Check Piston at TDC
  • Fitting the Cylinder Head
  • Check Compression Pressure
  • Check Hydraulic Tappets
  • Glow Plug System
  • Checking the Glow Plugs
  • Glow Plugs with Burnt Electrodes
• 2. Transmission
  • Digital Electric-Hydraulic Control (LHC)
  • Electronic Control of Truck Speed
  • Schematic Diagram of the Drive Unit
  • Technical Data of the Travel Drive System
  • Hydraulic Circuit Diagram
  • View of the Variable Pump
  • Cross Sectional View of Drive Pump
  • Electric-Hydraulic Adjustment
  • Hydraulic Adjustment with Electronic Control
  • Electric-Hydraulic Control
  • Begin of Pump Control
  • Swash Angle of Variable Pump
  • Hydraulic Zero Position
  • Hydraulic Brake Valve
  • Towing Device
  • Drive Axle AH 20-01 with Wheel Drive, Multiple Disc Brake and Hydraulic Motor
  • Repairing the Reduction Gear, Multiple Disc Brake and Hydraulic Motor
  • Renewing the Radial Sealing Ring of the Planetary Gear
  • Removing and Installing the Multiple Disc Brake and Hydraulic Motor with Swashplate
  • Truck Diagnostics and Troubleshooting
  • Electrical System Diagnostics
  • Working with the Linde Test Module
  • Diagnostics with a PC and the Linde Interface Converter
  • Linde Diagnostic Program
  • Menu Windows in Detail – LHC Software Versions
  • Hydraulic System Diagnostics
  • Test Aids
  • Power-Assisted Steering
  • Hydraulic Brake System
  • Hydrostatic Travel Drive
• 4. Steering System
  • Schematic Diagram of the Steering System
• 5. Controls
  • Pedal Stroke Adjustment Instructions
  • Adjustment Instructions for the Speed Control
  • Engine Speed Sensor Adjustment Instructions
• 6. Electrical System
  • Basic Diagram Diesel Version
  • Basic Diagram LPG Version
  • Diagram for Optional Equipment
  • Layout of Electrical Installation
  • Composite Instrument
• 7. Hydraulic System
  • Schematic
  • Sealing of the Control Valve
  • Setting of the Pressure-Limiting Valve
• 9. LPG Model of IC-Engined Fork Truck H 12/16/18/20 T-03, Series 350
  • Engine Specifications
  • Toothed Belt
  • Overall View of Toothed Belt Guard
  • Removing, Installing, Tensioning the Toothed Belt
  • Adjusting the Alternator V-Belt Tension
  • Cylinder Head
  • Removing and Installing the Cylinder Head
  • Electrical System
  • Electronic Ignition
  • TSZ-H Ignition System
  • Safety Measures for TSZ-Hall System
  • Installation of Distributor
  • Checking and Adjusting the Ignition Timing
  • Checking the TSZ-H Ignition System
  • Switch Unit A1
  • Hall Generator
  • LPG Installation
  • LPG Mixer

This Linde H12 H16 H18 H20 D-03 T-03 Series 350 Service Training Manual is far more than a basic owner’s handbook. It is a full technical training resource that walks through the diesel engine (VW ADG, 1896 cm3, 27 kW at 2200 rpm) and the LPG engine (VW ADF, 1781 cc, 27 kW at 2300 rpm) in genuine workshop detail. You get the toothed belt removal and tensioning procedure, injection pump timing values, cylinder head bolt tightening stages, compression pressure limits, hydraulic tappet inspection, glow plug current draw testing, and injector pressure specifications. The transmission section covers the LHC digital electric-hydraulic control, the HPV 55-02 variable pump, the AH 20-01 drive axle with multiple disc brake and hydraulic motor, plus the complete diagnostic workflow using the Linde Test Module or a PC with the Linde Interface Converter. Steering, pedal adjustment, engine speed sensor setting, the full electrical diagrams for both diesel and LPG versions, and the hydraulic system pressure-limiting valve settings are all included. For anyone maintaining a Series 350 Linde truck, this manual provides the exact figures, sequences and diagnostic fault-code explanations that generic repair guides simply do not contain.

What This Manual Enables You To Do

With this Linde H12 H16 H18 H20 D-03 T-03 Series 350 Service Training Manual on hand, you can carry out scheduled maintenance, diagnose electrical and hydraulic faults, remove and refit major components, and verify every critical adjustment against the manufacturer’s own training data. The diesel engine chapter alone supports timing belt replacement, injection pump removal and static timing, cylinder head removal and refitting with the correct four-stage tightening sequence, compression testing, and hydraulic tappet assessment. The transmission and LHC chapters let you configure the variable pump, set the hydraulic zero position, adjust the begin of pump control, and interpret every diagnostic fault code shown in the Linde Test Module windows. The electrical diagrams cover the diesel and LPG variants plus optional equipment, so wiring faults can be traced accurately instead of guessed at.

Correct procedures and specified torque values matter because these trucks use a hydrostatic travel drive and an electronically controlled variable pump. An incorrectly timed injection pump, a misadjusted swashplate angle or a wrongly calibrated traction potentiometer will cause poor performance, fault codes or damage. This manual gives you the exact figures – 420 +15 bar maximum pressure, 17.5 +0.5 bar boost pressure, 34.0 bar specified compression, 130 +8 bar injection pressure, 45 Nm camshaft sprocket torque, 90 Nm + 90 degrees crankshaft sprocket torque, and many more – so the job is done right the first time.

IMAGES PREVIEW

Delivery is instant. After payment you receive a downloadable PDF that opens on any computer, tablet or smartphone. There is no shipping, no waiting for a physical book, and you can print only the pages you need for the workshop. Keep the full manual on your device for quick reference during diagnostics, or print the sections relevant to the job in front of you.